2021 Mercedes-Benz AMG G63
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › AMG G63 › 2021
These records cover every 2021 Mercedes-Benz AMG G63. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2021 Mercedes-Benz AMG G63. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2023 G 550 and 2019-2022 G63 AMG vehicles that received a replacement door latch during a service visit or prior recall repair. Components within the right-side rear door latch may prevent the rear doors from latching or opening properly.
Risk and remedy
Risk
The rear door may appear closed even when the latch is not fully engaged, allowing the door to open while driving and increasing the risk of injury or a crash. Damaged latch components may prevent the rear door from being opened while inside the vehicle, increasing the risk of injury.
Remedy
Dealers will replace the right-side rear door latches, free of charge. Owner notification letters were mailed October 11, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. Vehicles in this recall that were previously repaired under recall 21V-353 will need to have the new remedy completed.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 G550 and AMG G63 vehicles. The front axle wiring harness may chafe against an oil cooler and become damaged, which can cause a loss of anti-lock brakes (ABS) and electronic stability control (ESC).
Risk and remedy
Risk
A loss of anti-lock brakes or electronic stability control can increase the risk of a crash.
Remedy
Dealers will inspect and either install a protective sleeve or replace the front axle wiring harness, as necessary, free of charge. Owner notification letters were mailed April 10, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 CLS450, AMG E53, AMG CLS53, E350, E450, AMG GT43, AMG GT53, 2020 S450, S560, G550, AMG GLC63, 2020-2021 GLC300, and AMG G63 vehicles. The side crash sensor connectors may come loose, which could delay the activation of air bags and seatbelts during a side impact crash.
Risk and remedy
Risk
Air bags and seatbelts that don't function as intended can increase the risk of injury during a crash.
Remedy
Dealers will inspect and replace as necessary, the side impact crash sensors, free of charge. Owner notification letters were mailed on September 3, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021070032/33.
Mercedes-Benz, LLC (MBUSA) is recalling certain 2021 G550, AMG G63, E350, E450, AMG CLS53, AMG E53, AMG GT43, AMG GT53, AMG GT63, 2021-2022 CLS450, and AMG E63 vehicles. The rear seat belt automatic locking retractors may deactivate early, which can prevent the child restraint system from securing properly. As such, these vehicles fail to comply with the…
Risk and remedy
Risk
An unsecured child restraint system can increase the risk of injury during a crash.
Remedy
Dealers will inspect, and replace as necessary, the rear seat belt assemblies, free of charge. Owners notified of the voluntary recall campaign by an interim letter on August 13, 2021. A final letter was mailed on September 24, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 G550 and G63 AMG vehicles. Components within the door latch may prevent the rear doors from latching or opening properly.
Risk and remedy
Risk
The rear door may appear closed even when the latch is not fully engaged, allowing the door to open while driving and increasing the risk of injury or a crash. Damaged latch components may prevent the rear door from being opened while inside the vehicle, increasing the risk of injury.
Remedy
Dealers will replace the rear door latches, free of charge. Owner notification letters were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. Note: Vehicles repaired prior to this recall must return to dealers to have the remedy performed. MBUSA's numbers for this recall are 2021060007 and 2021060014.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 C-Class, E-Class, E-Class Coupe and Convertible, GLC, CLS, AMG GT 4-door Coupe and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. A faulty electrical contact within the seat position switch may prevent the driver and passenger air bags and seat belt force…
Risk and remedy
Risk
Air bags and seat belts that do not perform properly in a crash can increase the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the seat position switches, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040016.
Owner complaints
2 complaints
What owners report most
Latest complaints
- Electrical system · Engine · Unknown or other
Kept going in for repairs for the same concerns - nothing was found —- now its a recall on the 2022 model for the same issue that my 2021 model has —- Malfunction in the front/ rear differential lock system malfunction.
- Lane departure › Assist
The lane keeping assistance is WAY to sensitive. Several times at just the slightest move towards the shoulder the car will brake and swerve. Its very alarming and needs to be recalibrated.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010964Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that the software for the engine control unit in the subject vehicles may not meet current specifications. As a result, the diagnosis for monitoring the air fuel ratio might not be activated in low load operation as intended. Consequently, this may not meet local regulatory requirements for on-board diagnostics and/or exhaust gas emissions. An authorized Mercedes-Benz dealer will update the Engine Control Unit software in the affected vehicles.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010440Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 G-Class (463 platform) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that on-board diagnostics and/or exhaust gas emissions requirements may not be fulfilled. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform the ECU software update.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008072Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
- 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
- 11008006Complaint "Active Distance Assist currently unavailable" and "Active Brake Assist functions currently limited" are shown on the instrument cluster during startup or while driving AND stored DTC in quick test U0416FE - "Implausible data were received from control unit Traction system" in A108/1 (Distronic). Cluster messages will remain and mentioned system functionality is limited until key is cycled. Cause Under investigation. Symptom may occur with one or a combination of the following: 1. Low battery health 2. Battery state of charge 3. Repeated short drive cycles. Cluster messages will resolve after a vehicle key cycle. Remedy Please open a TIPS case with: Quick test A108/1 (Distronic) control unit log Instrument cluster message memory Driving Battery Cycle "Individual values while driving" Log (Front SAM) Battery health Battery state of charge
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007965Complaint When unpacking vehicles with magno night black paint (code 056U) from the full transportation packaging, the paintwork may exhibit white stains/shades on the hood. These are mainly present on the hood, fenders and the bumpers. Cause Moisture ingress under the full transportation packaging can lead to it penetrating the fresh paint thereby causing it to swell up. Easily visible, white stains/shades on the paint surface would be the consequence. Remedy Carefully heat any prominent areas using a heat gun (up-to 900F, at distance of approx. 3-5 inches), it may be necessary to repeat this process several times. Use a maximum of 120 C for component parts made of plastic, such as bumpers. If this method does not provide a remedy, the paint structure is irreversibly damaged and not repairable. In such instances, the component part must be repainted. IMPORTANT! Make sure that no seals or other heat-sensitive component parts in the working area or behind the component part are damaged.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005263Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2024 G-Class (463 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110 or FMVSS 120. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this non-compliance is inconsequential as it relates to motor vehicle safety.
- 11005252Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2024 G-Class (463 platform) vehicles, the B-pillar certification label might not contain the vehicles rim size, tire size, and cold tire inflation pressure information as required by FMVSS 110 or FMVSS 120. In this case, relevant regulatory requirements might not be met. Mercedes-Benz believes this issue has no impact on vehicle safety. Mercedes-Benz intends to submit a petition to NHTSA for exemption from the notification and remedy requirements of 49 U.S.C. chapter 301, pursuant to 49 CFR Part 556, on the basis that this non-compliance is inconsequential as it relates to motor vehicle safety.
- 11000624The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19+ G63 there may be an alternate solution available. Please reference LI07.61-P-076755 before performing the steps in this LI.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248212In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year ("MY") vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition: In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ("MIL") to illuminate. Please follow the work instructions added to this NCU to remedy the issue. Please be advised that all repairs being claimed under this extended warranty must have a quick test uploaded with the following fault code information and may be audited. P012800 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 20102 - Insert, coolant thermostat o 52 - Does not operate correctly o 41 - Hard closing 20103 - Housing/cover, coolant thermostat o 73 - Electrical fault 2030T - Heating element, coolant thermostat o 53 - Insufficient effect/power o 73 - Electrical fault
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10244752Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that the software for the engine control unit in the subject vehicles may not meet current specifications. As a result, the diagnosis for monitoring the air fuel ratio might not be activated in low load operation as intended. In addition, catalytic converter aging might not be immediately detected and so, may not illuminate a check engine Malfunction Indicator Lamp (MIL). After a cold start in the "catalytic converter heating" operating mode, misfires might occur and the check engine MIL would be illuminated. Consequently, these issues may not meet local legal requirements for on-board diagnostics and/or exhaust gas emissions. MBUSA will conduct a voluntary Emissions Recall Campaign in which an authorized Mercedes-Benz dealer will update the software in the affected vehicles.
- 10241530Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year 2021 C-Class (205 platform), CLA (118 platform), G-Class (463 platform), GLC (253 platform), GLA (247 platform) and GLE/GLS (167 platform) vehicles, the installed ignition coils may not correspond to current specifications. As a result, a misfire could occur, followed by potentially reduced engine output, and illumination of the check engine Malfunction Indicator Lamp (MIL). This may also cause exhaust emissions to increase. MBUSA will conduct a voluntary Emissions Recall Campaign in which an authorized Mercedes- Benz dealer will replace the ignition coils.
- 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
- 10240158Complaint. Customer complains that CEL is active in instrument cluster. May also report rough running. Cause. Software. Remedy. Please update the ME control unit software. The new software should include 177021216. Ensure that a sensor rotor adaptation is conducted afterwards per the instructions in Xentry. Assess the vehicle afterwards and if the complaint is remedied, release the vehicle. If the customer complaint is not remedied, process the vehicle via LI07.61-P-070707 and open a TIPS case with your findings. If the vehicle is already at this software level or if software is not available, process the vehicle via LI07.61-P-070707 and open a TIPS case with your findings.
- 10240156Complaint The customer may complain of the vehicle not starting after being turned off, a yellow 12v Battery Warning message in the instrument cluster and/or a CEL that upon investigation points towards one or more exhaust flaps not responding. The alternator charging management strategy in the software must be modified. Update the ME control unit software. The software should include 177021216. If the vehicle already has this software, stop and open a TIPS case. If there is no newer software available, stop and open a TIPS case. After updating a sensor rotor adaptation MUST be conducted. Once completed the vehicle can be released to the customer.
- 10231032Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead.
- 10228807Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams.
- 10222461Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10219259Complaint CEL on with Code P012800 "The Coolant Temperature is Below the Specified Temperature" Cause Under investigation. This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy Due to formatting issues please see "remedy instructions" in attachments
- 10217162Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10217157Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
Every Mercedes-Benz AMG G63 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.