2021 Mercedes-Benz AMG GLC63 S

Recalls

3 recalls name the 2021 Mercedes-Benz AMG GLC63 S. Newest first.

• Fuel system, gasoline › Delivery › Fuel pump

  Jun 26, 2023NHTSA 23V445000143,551 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.

  Risk and remedy

  Risk

  A loss of drive power can increase the risk of a crash.

  Remedy

  Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.

  Full recall details →

• Exterior lighting › Headlights

  Apr 15, 2022NHTSA 22V261000129 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLC 300, GLC 300 4Matic, AMG GLC 63 4Matic, AMG GLC 63 S 4Matic, and AMG GLC 43 4Matic vehicles. The electrical connection for the headlights may not be watertight, which can result in headlight failure.

  Risk and remedy

  Risk

  Headlight failure can decrease visibility for both the driver and surrounding traffic, increasing the risk of a crash.

  Remedy

  Dealers will inspect and replace the headlight sealing plugs, as necessary, free of charge. Owner notification letters were mailed June 3, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022050005.

  Full recall details →

• Air bags › Sensor › Occupant classification

  Apr 1, 2021NHTSA 21V2300008,634 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 C-Class, E-Class, E-Class Coupe and Convertible, GLC, CLS, AMG GT 4-door Coupe and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. A faulty electrical contact within the seat position switch may prevent the driver and passenger air bags and seat belt force…

  Risk and remedy

  Risk

  Air bags and seat belts that do not perform properly in a crash can increase the risk of injury.

  Remedy

  MBUSA will notify owners, and dealers will replace the seat position switches, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040016.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
• 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
• 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11003212Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. 3. NOTE: Coding Parameter 'Shimmy' should be turned off and the actual value should read "Shimmy aus". With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11003205Complaint The driver's seat memory settings do not synchronize with the driver's user profile as described in the operator's manual. Driver's seat settings are not transferred to the vehicle. Cause The driver's seat does not support the profile synchronization feature on these vehicles. Remedy There is no remedy for this complaint. The vehicle is working as designed. Note: Do not replace any parts.
• 11000624The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19+ G63 there may be an alternate solution available. Please reference LI07.61-P-076755 before performing the steps in this LI.
• 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
• 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10252835Always use the latest XENTRY Diagnosis software release with all available add-ons. Make sure to follow the operation steps exactly as described in XENTRY Diagnosis. Use a battery charger to ensure sufficient power supply of the vehicle on-board electrical system battery (greater than 12.5 V). If XENTRY Diagnosis is already connected to the vehicle, start with operation step 2. If two or more software updates or SCN codings are performed during one workshop visit, operation items 02-4762 and 02-5058 may be invoiced only once for each workshop order. Work procedure 1. Connect XENTRY Diagnosis. 2. Update N129/1 - power electronics (SG-EM) control unit software. To do this, select menu item "Quick test view N129/1 - power electronics (SG-EM) Adaptations Control unit update Update of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
• 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
• 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
• 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
• 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
• 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
• 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
• 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
• 10248212In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year ("MY") vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition: In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ("MIL") to illuminate. Please follow the work instructions added to this NCU to remedy the issue. Please be advised that all repairs being claimed under this extended warranty must have a quick test uploaded with the following fault code information and may be audited. P012800 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 20102 - Insert, coolant thermostat o 52 - Does not operate correctly o 41 - Hard closing 20103 - Housing/cover, coolant thermostat o 73 - Electrical fault 2030T - Heating element, coolant thermostat o 53 - Insufficient effect/power o 73 - Electrical fault
• 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
• 10244748Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-23 C-Class, EQS, S-Class, SL, EQE, GLC (206, 296, 297, 223, 232, 294, 295, 254 platform) vehicles, the head unit software will be updated remotely to MBUX 2.4. With this update, customers will benefit from many new functions and features, such as video streaming (note that the Entertainment Package Plus is required for streaming and can be purchased from the Mercedes me Store by the end of 2023), Dolby Atmos, MBUX Voice Assistant (NewsFlash & Tourguide), a personal decorative image on the front passenger display, and more. Please see NCU issued on September 5th, 2023 from Product Management and Digital House team Additional New Connected Features Coming Soon. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. No customer letter will be mailed for this software update.
• 10244745Sliding sunroof panel of panoramic sliding sunroof reversed (temporarily, once, multiple times) during closing process without entrapment event. Sensitive parameterization of the automatic reversing function of the panoramic roof. Perform SW update of panoramic roof control unit (PSD, A98, TSSR254).
• 10244735Wheezing noises from the front shock absorbers when passing over surface undulations and rough road. The noises may become more conspicuous with warm damper oil. The flow noises of the damper oil are currently being analyzed. The wheezing noises are currently considered standard for the series. Replacing the shock absorbers will yield no benefit and will not remedy the problem. Please report complaints regarding these wheezing noises via TIPS.
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10241530Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year 2021 C-Class (205 platform), CLA (118 platform), G-Class (463 platform), GLC (253 platform), GLA (247 platform) and GLE/GLS (167 platform) vehicles, the installed ignition coils may not correspond to current specifications. As a result, a misfire could occur, followed by potentially reduced engine output, and illumination of the check engine Malfunction Indicator Lamp (MIL). This may also cause exhaust emissions to increase. MBUSA will conduct a voluntary Emissions Recall Campaign in which an authorized Mercedes- Benz dealer will replace the ignition coils.
• 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
• 10240250Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2021-2024 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the head unit software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as either Software Update MBUX 2.4 or Software Update Hermes 1.5 E522.8. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.

Every Mercedes-Benz AMG GLC63 S model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.