2024 Mercedes-Benz AMG GLC63 S E

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11010188Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY24-25 C-Class, CLE, E-Class, GLC (206, 236, 214, 254 platform) vehicles, the infotainment system does not correspond with the latest series production configuration. The infotainment system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008977Complaint Combustion engine could no longer be started, only electric driving possible. Cause High-voltage belt-driven starter-alternator faulty. Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the required HV qualification to work on HV system.
• 11008885Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023 2024 C-Class (206 platform) and GLC (254 platform) vehicles, the door control unit software does not correspond to current production specifications. In this case, the 12V starter battery may sporadically discharge. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the door control unit software.
• 11008879Complaint This document applies to vehicles of model series 206 and 254 from SOP (start of production) with NTG7, that do not have SA code 367: The Live Traffic Information Digital Extra is missing, is not available or does not work, even though the license has been purchased from the Mercedes me Store. Cause Problem with the store's offer provision for Digital Extras. Remedy Remedial action is currently being prepared. For the time being, do not undertake any work (SW updates, commissioning, hardware exchanges and similar). These are not effective, as an adaptation of the back end needs to be carried out first. For now, please do not add (arrange to add) SA code 367 manually. As soon as the adaptation has been implemented, this document will be modified accordingly and the necessary steps added. If a customer does not wish to wait for the fix, please direct them to contact the CAC for a refund of the Live Traffic service.
• 11008877Complaint Sliding sunroof panel of panoramic sliding sunroof reverses (temporarily, once, multiple times) during closing process without entrapment event: a) from tilt position b) from sliding position Cause a) Sensitive parameterization of the automatic reversing function of the panoramic roof b) Sluggish operation through tolerances of various component parts in the roof mechanism, in particular, at higher temperatures Remedy a) Leave the sliding sunroof panel of the panoramic roof in the rear sliding position (fully open position) for at least 30 minutes (or overnight if necessary), then perform commissioning of the panoramic roof control unit (PSD, A98, TSSR254) b) Perform commissioning of panoramic roof control unit (PSD, A98, TSSR254) Reference to escalation closing during reversing processes (also described in Operators Manual), if vehicle in customer possession (see Video_1): If the panoramic roof blocks up when closing and then opens again slightly (reversing process): Immediately after automatic reversing, wipe forwards on the control panel of the overhead control panel and hold until the panoramic roof is closed. The panoramic roof is closed with greater closing force. If the panoramic roof blocks up again and then opens again slightly (reversing process): repeat previous step. The panoramic roof is closed again with greater closing force.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008062Complaint The electric range does not meet customer's expectations. Cause The following information is being provided for educational purposes only: At Mercedes-Benz, we believe that our vehicles should display to the driver a range that in all probability can actually be achieved. These ranges are predictions - the range actually achieved may therefore differ from the range shown. The calculation for the predicted range takes into account the current outside temperature, the set temperature of the air conditioning system, the battery capacity and the characteristics of previous journeys (sporty/anticipatory driving style). Where previous journeys are concerned, factors given particular consideration are individual driving style and the use of other power consumers (seat heating, lights, charging function for smartphones, etc.). It is therefore possible that data from the last few hundred kilometers driven is also used in the calculation. Consequently any change in usage behavior will only slowly affect the predicted range. If active navigation or active commuter route is used, additional information about the route ahead (for example elevation profile, traffic volume) can be included in the range calculation. Remedy The customer's individual input to the range can be reset. Depending on the vehicle, the reset can be done in the instrument cluster or the head unit. For plug-in hybrid vehicles of model series 166 (all), 205 (up to modification year 18/1), 213 (up to modification year 17/2), 222 (up to modification year 17/2), 253 (up to modification year 19/1), the range can be reset by resetting the trip computer ("From reset", "From start" and "Day cycle counter"). After the reset, a value based on the certified range will be shown. For electric and plug-in hybrid vehicles of model series 205 (from modification year 18/2), 213 (from modification year 18/1), 222 (from modification year 18/1), 253 (from modification year 19/2) and model series 118, 167, 177, 206, 223, 247, 293, 295, 297 a reset is only possible by resetting the head unit to the factory settings. This will delete all saved customer data and any settings made (e.g. radio settings, navigation destinations). If necessary, therefore, back up the customer data onto a USB flash drive using the Backup function before performing a reset. As from vehicles with NTG 7, Mercedes me is used for the making the backup. After the reset, an empirical value is displayed that is based on normal use of the vehicle and the current climatic conditions (set temperature and outside temperature - commensurately higher values will be achieved if the air conditioning system is switched off). Depending on driving style, outside temperature and which power consumers are actually switched on, the achieved range may significantly exceed this range, but likewise may also fall significantly short of it. Further information on battery capacity and aging can be found in document SI47.70-P-0070A.
• 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006636Complaint Combustion engine can no longer be started, only electric driving possible Cause High-voltage belt-driven starter-alternator has a failure Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the qualification "T1716F Diagnosis at high voltage level 4" and the vehicle-specific training. Note: In order to check whether the high-voltage belt-driven starter-alternator has a failure, please carry out the test below. If the fault "P0E2F00 The electrical fuse B for the high voltage has a malfunction" is stored in the N82/10 BMS control unit, the HV protocol must be checked to see whether the fuse for the auxiliary consumers has a failure. In this case, the high-voltage battery must be replaced after the short circuit has been eliminated. (See attachment) The faulty component high-voltage belt-driven starter-alternator must always be sent back via the existing return delivery process for analysis. Check: Please disconnect the high-voltage plug at the high-voltage belt-driven starter-alternator and connect test adapter 000 589 94 63 00. Measure resistance HV+ to HV-. If the final measurement result is between 01 ohm, the high-voltage belt-driven starter-alternator with the short circuit must be replaced. If either one of or both the fault codes P0C0B16 and P0C0B17 are saved in the high-voltage belt-driven starter-alternator control unit G2/3, please replace the high-voltage belt-driven starter-alternator, since no short circuit can be measured here and this therefore concerns a hardware failure. Please check the serial number on the silver adhesive label below the SW number on the front of the high-voltage belt-driven starter-alternator. Example: 2314300044 (the first 10 digits, see attachment) Important note: If the number is small or greater than 2329100027, a TIPS case must be created. In this instance, please attach the following documents to the TIPS case: Quick test High-voltage event log Picture of the silver adhesive label on the front of the high-voltage belt-driven starter-alternator (serial number) Attach the measurement results with pictures approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11003095Complaint Sliding sunroof panel of panoramic sliding sunroof reverses (temporarily, once, multiple times) during closing process without entrapment event: a) from tilt position b) from sliding position Cause a) Sensitive parameterization of the automatic reversing function of the panoramic roof b) Under analysis Remedy a) Leave the sliding sunroof panel of the panoramic roof in the rear sliding position (fully open position) for at least 30 minutes (or overnight if necessary), then perform commissioning of the panoramic roof control unit (PSD, A98, TSSR254) b) Perform commissioning of panoramic roof control unit (PSD, A98, TSSR254)
• 11000740An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk of your vehicle, free of charge. The bottle may potentially leak and may not be available for use in case of a flat tire. Your vehicle must be brought to a dealer to complete this campaign. Please schedule an appointment by contacting our Customer Assistance Center at 1-800-367-6372, or locate your nearest dealer using the QR code and Find a Dealer section.
• 11000544Sliding sunroof panel of panoramic sliding sunroof reversed (temporarily, once, multiple times) during closing process without entrapment event. Cause remains open. For analysis, the information from the control unit log of the panoramic roof control unit (TSSR254) is required via a TIPS case. Further analyses Requirement: The teach-in run for the automatic reversing function of the panoramic roof via XENTRY has still NOT been carried out SW-SNR is A254 902 9702 with parameter data set A254 903 2902 or A254 903 4802 Please perform the following steps: 1. Create a TIPS case 2. Create control unit log of panoramic roof control unit (TSSR223, A98, PSD) (prerequisite: add-on 25071) and attach to TIPS case
• 11000541Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11000534Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 22-24 C-Class, EQE, EQS, GLC, S-Class, SL (206, 294, 295, 296, 297, 254, 223, 232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11000519Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023-2024 C-Class, CLE, E-Class, EQE, EQS, GLC, GLE, GLS, GT, S-Class, and SL vehicles (205, 206, 236, 213, 214, 238, 294, 295, 296, 297, 253, 167, 290, 223, 232 platform), the tire sealant bottle may not meet specifications. The possibility exists that the tire sealant bottle may leak within the installation location. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.
• 10253704TEMPORARY DEACTIVATION OF CAMPAIGN DUE TO DIFFICULTY WITH THE SOFTWARE UPLOAD. AN UPDATED NCU WITH WORK INSTRUCTIONS WILL BE PROVIDED ONCE AVAILABLE. The vehicles were visible and flagged in VMI as "OPEN" on March 28, 2024. The affected vehicles will be removed from display in VMI on April 12, 2024, due to difficulties with the software upload. An update NCU with WI will be posted once available.
• 10252837Check right tailgate, rework if necessary Check/test procedure 1. Remove top center rear spoiler. For basic data, see AR72.20-P-4000WT. 2. Check outer top right of rear-end door for constriction and crack formation (Figure 1). a. No crack or sheet metal constriction present on outer right of rear-end door: End measure. b. Crack or sheet metal constriction present on outer right of rear-end door: Carry out work procedure. Work procedure 1. Remove side spoiler on right rear-end door. For basic data, see AR72.20-P-4000WT. The right side spoiler must be replaced. 2. Drill off crack/sheet metal constriction on outer right of rear-end door at ends using a 23 mm drill bit. 3. Clean rear-end door in processed area, apply anticorrosion protection, and rework/seal the crack with seam sealant. Ensure cavity preservation according to manufacturer's specifications. 4. Assemble in reverse order.
• 10252747This is to notify you of the Service Campaign Launch to update the digital and replace the printed operators manual in 39 Model Year (MY) 2024 GLC, GLS, and AMG GT vehicles (167, 254, 192 and 290 platform). The vehicles will be visible and flagged in VMI as OPEN on March 22, 2024. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2024 GLC, GLS, and AMG GT vehicles (167, 254, and 290 platform), the digital and printer operators manual may not correspond to current production specifications. Customers may have received the description of certain functions that are not applicable to their vehicle. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the digital and replace the printed operators manual.
• 10252710Mercedes-Benz AG, the manufacturer of Mercedes-Benz, has determined that on certain MY 2024 C-Class, GLC, and S-Class (206, 223, 254 platform) vehicles, the electronic ignition lock control unit software does not meet current production specifications. Therefore, it is possible that the free access function (code 871) may not be available. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the N73/3 electronic ignition lock control unit software.
• 10249539No audio is output either in radio mode, or with media playback via app, Bluetooth or USB. In such cases, "Playback not active" is shown in the display. Mute line between communication module N112/2 and sound control unit N40/3. Check mute cable (violet) between control units for communication module N112/2 and sound N40/3, including plug contacts, and repair or replace as necessary. If the plug contact is deformed, it is imperative that its counterpart at the control unit is also checked.
• 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
• 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
• 10248167Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023 GLC (254 platform) vehicles, the panoramic sliding sunroof control unit software does not correspond to the latest series production configuration. In rare cases, the sensitivity of the automatic reversing function may prompt an incorrect reversal of the sliding sunroof panel. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the Panoramic Sliding Sunroof Control Unit software.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10244745Sliding sunroof panel of panoramic sliding sunroof reversed (temporarily, once, multiple times) during closing process without entrapment event. Sensitive parameterization of the automatic reversing function of the panoramic roof. Perform SW update of panoramic roof control unit (PSD, A98, TSSR254).
• 10244735Wheezing noises from the front shock absorbers when passing over surface undulations and rough road. The noises may become more conspicuous with warm damper oil. The flow noises of the damper oil are currently being analyzed. The wheezing noises are currently considered standard for the series. Replacing the shock absorbers will yield no benefit and will not remedy the problem. Please report complaints regarding these wheezing noises via TIPS.
• 1024330612V message in IC when starting the vehicle. SW updates need to be performed. Follow the guided test for FC U116000 in N73/3*1 EIS CU. Perform the SW checks and updates. Fully charge both 12V and 48V batteries. After, perform a few drive/park cycles with at least 1 overnight park cycle. If the 12V message is no longer present, release the vehicle.
• 10241536Phone call log is not shown in the MBUX display. If the telephone connects with the head unit again, the call log may not be sent. Current software release for the A26/17 - MBUX multimedia system (Head unit) Currently there is no remedy available. Replacing the hardware will not resolve the symptom. New software for the A26/17 - MBUX multimedia system (Head unit) will be made available with software version E444.x (scheduled for Q4/2023)
• 10241519Noise at front seats between seat-back lining and function carrier. Noise is caused by friction of the two component parts. Remove the seat-back lining (back panel) of the front seat concerned using a special tool. Via adhesive bonding, affix 2 pieces of felt at the lower seat backrest structure (see pic. 1). Via adhesive bonding, affix 2 pieces of felt in the upper area of the seat backrest at the function carrier (see pic. 2). Pic. 3 shows the function carrier from behind: Begin applying the adhesive bonding of the felt at the edge (see red arrow). Ensure that the adhesive bonding is applied in the center. Then fold the felt forward. Pic. 4 shows the function carrier from the front: Continue to apply the adhesive bonding to the forward fold. Ensure that the adhesive bonding is applied in the center.
• 10241515When operating a control point to open the trunk lid or the tailgate, the trunk lock unlocks, but there is no actuation of the trunk control/tailgate control drive unit (M51/3). Faulty microswitch signal of trunk lock. In the event of a problem, the status of the trunk lock (picture 1) does not change during opening/closing of the trunk lid or tailgate. The function of the interior trunk release is not affected. Replace trunk lock (A85/5).
• 10241510In the instrument cluster, the symbol for "12 V battery" and the message "Switch on vehicle" may sporadically be displayed. As a consequence of this, the fault codes B 1 FCB97 (=> N73/3) and U 116000 (=> N73/3*1) are stored in the fault memory. In the subsequent analysis of the 12 Von-board electrical system data, the following parameters are conspicuous (see picture 1 in the attachment): Charge balance negative when stationary. Interior CAN bus is awake for an unusually long time. 12 V battery SOC (state of charge) during subsequent engine start is 45% or less. NOTE: Once the 12 V battery SOC has exceeded 50% for the first time, the symbol and the message in the instrument cluster disappear again. The door control unit (N69/x) may sporadically keep the interior CAN bus awake. NOTE: Exclusively door control units with the HW item numbers A2239019917 and A2239010018 can be affected. Open a TIPS case and include the following: 1. Initial Quick Test 2. N73/3 EZS CUL 3. N73/3*1 EZS CUL 4. Date and time of occurrence

Every Mercedes-Benz AMG GLC63 S E model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.