2021 Mercedes-Benz AMG GT63S

Recalls

3 recalls name the 2021 Mercedes-Benz AMG GT63S. Newest first.

• Back over prevention › Sensing system › Camera

  May 14, 2021NHTSA 21V354000343,191 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…

  Risk and remedy

  Risk

  A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.

  Remedy

  The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.

  Full recall details →

• Air bags › Sensor › Occupant classification

  Apr 1, 2021NHTSA 21V2300008,634 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 C-Class, E-Class, E-Class Coupe and Convertible, GLC, CLS, AMG GT 4-door Coupe and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. A faulty electrical contact within the seat position switch may prevent the driver and passenger air bags and seat belt force…

  Risk and remedy

  Risk

  Air bags and seat belts that do not perform properly in a crash can increase the risk of injury.

  Remedy

  MBUSA will notify owners, and dealers will replace the seat position switches, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040016.

  Full recall details →

• Electrical system › Starter assembly

  Mar 26, 2021NHTSA 21V217000493 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2018-2021 E63S AMG, E63S AMG Wagon, 2019-2021 AMG GT63 4-door, and AMG GT63S 4-door vehicles. The starter motor positive cable may not have been installed correctly, potentially allowing the power supply harness wires to chafe.

  Risk and remedy

  Risk

  Damaged wires may cause a short circuit and result in a vehicle stall, increasing the risk of a crash. Also, a short circuit can increase the risk of a fire.

  Remedy

  MBUSA will notify owners, and dealers will inspect and, as necessary, correct the screw connections and position of the positive cable, free of charge. Owner letters were mailed May 18, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040013.

  Full recall details →

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11010445Complaint Rear spoiler sporadically remains in opened position or does not extend and a fault message appears in the instrument cluster. The rear spoiler can then no longer be retracted manually using the button. The function of the rear spoiler is re-established after an ignition reset and the fault message is no longer present in the instrument cluster. Cause Possible causes: Coding of the AMG DRIVE UNIT for recognition of Hall sensor when retracting rear spoiler. Hardware tolerances / hardware wear Remedy If new software for the AMG DRIVE UNIT is available, carry out the software update. If the vehicle already has the most current version of the AMG DRIVE UNIT software installed, conduct SCN coding of the AMG DRIVE UNIT. Software remedy: Up to YoM 19/2 -> AMG Drive Unit N145/1 Software A001 902 6208 As of YoM 20/1 up to YoM 20/2 -> AMG Drive Unit N145/1 Software A001 902 6108 As of YoM 21/1 -> AMG Drive Unit N145/1 Software A001 902 6008 Then check the currently learned actual values under the path "DRVU -> Actual values -> Rear wing sensor system": Are the actual values all in the specified range (green): --> Subject the vehicle to a final inspection/test drive and, if the findings report is OK, hand it over to the customer. If the actual values are outside of the specified range (red) or final inspection is not OK: --> Initialize the rear spoiler (if necessary up to 5x) until all values are in the target range (green). If subsequently OK: -> Subject the vehicle to a final inspection/test drive and, if the findings report is OK, hand it over to the customer. If still not OK: -> Check screw connection of rear spoiler adjuster (see attachment 1) for tight seating. If screws loose: -> Bond loose screw (see following steps and attachment 3 to 5). 1. Unscrew screw with Torx TX25 screwdriver from the housing guide. 2. Dip screw in Loctite 603 (at least 3 threads) 3. Screw the screw back into the housing guide with 2 Nm torque. (IMPORTANT: Loctite 603 finger-tight after 8 minutes and cured after 24 hours) 4. Initialize rear spoiler after the curing time. 5. Subject the vehicle to a final inspection/test drive and, if the findings report is OK, hand it over to the customer. If screws tight: -> Create a TIPS case with the following information: 1. When exactly does the fault message appear (at which speed, when accelerating or braking, automatic mode, etc.)? 2. Is the problem sporadic or continuous? 3. Does the fault message disappear following an ignition reset/BUS idle and is the function of the rear spoiler then (momentarily) restored? 4. Is the fault reproducible and if so, how? Attach the following files: 1. Quick test 2. Control unit log for AMG DRIVE UNIT + rear wing (DRVU + HFL) 3. IC event memory 4. Currently learned actual values prior to initialization 5. Currently learned actual values following initialization 6. Power consumption of rear spoiler (XENTRY: Configuration -> Coding -> Coding of power parameter) 7. Photo of the label on the rear spoiler drive (IMPORTANT: Production/manufacturing date of the rear spoiler must be easily readable, for an example see attachment 2)
• 11009205Complaint DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button. Vehicle will shift into park automatically at ignition off or with opening the driver door. Cause Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Note: This repair may not be covered by warranty due to outside influence. Remedy Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas. We recommend an electrical contact cleaner such as BW-100 or CRC QD Electronic Cleaner as example. 7. Assemble and check for proper function
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11009025Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
• 11008977Complaint Combustion engine could no longer be started, only electric driving possible. Cause High-voltage belt-driven starter-alternator faulty. Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the required HV qualification to work on HV system.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008007Complaint Message in the instrument cluster regarding rear axle steering In the short test, the fault > Actuator blocked < appears Cause Vehicle may detect high adjustment force in the rear axle steering. Remedy NOTE: If hardware and software numbers do not match exactly what is listed below, please follow DTC guided tests. Old Hardware: A 290 460 3300 / 3400 > SW A 290 902 7400 Caution! This hardware cannot be flashed with the new software version. Only the current hardware with the corresponding previous software release can be flashed. If the vehicle still has the old hardware installed, do not attempt to flash; instead, please create a TIPS case. Current Hardware: A 290 460 3900 / 4000 >> SW A 290 902 5101 This hardware can be flashed with A 290 902 1005. Flash control unit N68/3 and N68/4 with current software release A 290 902 1005 using XD.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007956Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2023 CLS (257 platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
• 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
• 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
• 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
• 11006595Complaint Customer states that either the yellow battery indicator lamp is illuminated in the instrument cluster OR a 4MATIC malfunction MIL is present, AND the subject vehicle is affected by the pending recall Replace Transmission Wiring Harness (NHTSA ID 24V445). The following DTCs may also be present in the initial quick test: In N45 - All-wheel drive (AWD): U103E00 Communication with the suspension FlexRay has a malfunction In N73 - Electronic ignition lock (EZS): U116000 A bus keepawake control unit has been detected Cause Possible water entry into connector X279x1 Remedy Immediately disconnect electrical connector X279x1 and create a TIPS case. Further instructions will be provided in case Please attach the following documents to the TIPS case: Initial quick test Instrument Cluster event memory Detailed photos of both ends of electrical connector X279x1
• 11006544Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and /or charging / or parking? If the complaint occurred while charging, how long after did the complaint/IC message occur? Which charging station was used, which provider (picture if possible)? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger
• 11005349Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and/or charging? If the complaint occurred while charging, how long after did the complaint/IC message occur? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below. Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger Test with different charging station
• 11005348Complaint Message in the instrument cluster regarding rear axle steering In the short test, the fault > Actuator blocked < appears Cause Vehicle may detect high adjustment force in the rear axle steering. Remedy Old Hardware: A 290 460 3300 / 3400 > SW A 290 902 7400 Caution! This hardware cannot be flashed with the new version. Only the current hardware with the corresponding previous software release can be flashed. If the vehicle still has the old hardware installed, do not attempt to flash; instead, please create a TIPS case. Current Hardware: A 290 460 3900 / 4000 >> SW A 290 902 5101 This hardware can be flashed with A 290 902 1005. Flash control unit N68/3 and N68/4 with current software release A 290 902 1005 using XD.
• 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
• 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11003209Complaint DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Cause Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Remedy Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- follow available guided test remedy.
• 11000624The customer complains of a check engine light (CEL) on. May also complain of the engine running roughly and/or a loss of power. Multiple Causes Remedy Please see the document "Remedy Instructions" in attachments. For MY19+ G63 there may be an alternate solution available. Please reference LI07.61-P-076755 before performing the steps in this LI.
• 11000543DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- open TIPS Case (send to Body/Chassis/Entertainment Inbox)
• 10253719DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- open TIPS Case
• 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10252773The following symptoms may be present in the instrument cluster: 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. First manually commission the already installed instrument cluster control unit N133/1 and then perform the special procedure to re-initialize ASSYST data in powertrain control unit N127. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
• 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
• 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
• 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
• 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
• 10248212In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the engine thermostat (including software update) installed in certain Model Year ("MY") vehicles (with engines M176, M177, M178) listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first), due to the following condition: In the affected vehicles, the sealing ring in the engine thermostat could detach, causing a delay in the heating of the engine coolant. This may also cause the check engine Malfunction Indicator Lamp ("MIL") to illuminate. Please follow the work instructions added to this NCU to remedy the issue. Please be advised that all repairs being claimed under this extended warranty must have a quick test uploaded with the following fault code information and may be audited. P012800 - Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 20102 - Insert, coolant thermostat o 52 - Does not operate correctly o 41 - Hard closing 20103 - Housing/cover, coolant thermostat o 73 - Electrical fault 2030T - Heating element, coolant thermostat o 53 - Insufficient effect/power o 73 - Electrical fault
• 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.

Every Mercedes-Benz AMG GT63S model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.