2008 Mercedes Benz C63

Recalls

3 recalls name the 2008 Mercedes Benz C63. Newest first.

• Air bags › Frontal › Passenger side › Inflator module

  May 26, 2016NHTSA 16V363000258,163 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2008-2011 C300 Sedan, C300 4matic Sedan, C350 Sedan, C63 AMG Sedan vehicles, 2010-2011 GLK350, GLK350 4-Matic and E350 Coupe vehicles, 2011 SLS AMG, E350 Convertible, E550 Coupe and E550 Convertible vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii…

  Risk and remedy

  Risk

  An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

  Remedy

  MBUSA will notify owners, and dealers will replace the passenger frontal air bag modules, free of charge. Owners were sent an interim notification October 2016. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

  Full recall details →

• Air bags › Frontal › Sensor/control module-inactive

  Oct 27, 2015NHTSA 15V711000127,504 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2008-2009 C300 Sedan, C300 4Matic, C63 AMG, and C350 vehicles, and 2010 GLK350 and GLK350 4Matic vehicles. Due to a manufacturing error, the air bag control unit may corrode and cause the control unit to malfunction.

  Risk and remedy

  Risk

  The malfunctioning air bag control unit may cause the air bags to unexpectedly deploy increasing the risk of injury and the possibility of a vehicle crash. Alternatively, the air bag control unit malfunction may cause the air bags to not deploy in the event of a crash necessitating air bag deployment, increasing the risk of occupant injury.

  Remedy

  MBUSA will notify owners, and dealers will inspect the air bag control unit and replace it, as necessary, free of charge. Mercedes-Benz issued an interim notification to owners on December 23, 2015. The recall began on March 14, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Exterior lighting › Tail lights

  Apr 11, 2014NHTSA 14V177000252,867 vehicles

  Mercedes-Benz USA, LLC (Mercedes) is recalling certain model year 2008-2011 C300, C300 4Matic, C350, and C63 AMG vehicles manufactured January 26, 2007, through July 13, 2011. In the affected vehicles, a poor electrical ground connection may result in the dimming or failure of the tail lights.

  Risk and remedy

  Risk

  Dimming or failure of the tail lights reduces the ability to warn other motorists of the driver's intentions of stopping or turning, increasing the risk of a crash.

  Remedy

  Mercedes will notify owners, and dealers will replace the bulb holders if not previously updated and replace any corroded connectors, free of charge. The recall began on August, 18, 2014. Owners may contact Mercedes at 1-800-367-6372.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system2
2. Exterior lighting2
3. Unknown or other2
4. Fuel/propulsion system1
5. Steering1

Latest complaints

• Jul 15, 2016TX135,000 mi
  Electrical system · Unknown or other
  The electronic steering control lock module went out on my car. This seems to be a reoccurring issue with any "W204" 2008/2009 mercedes benz model car. I've documented over a few hundred cases alone on the forums online. This IS a dealership only fix and should be recalled. Basically, security…

  The electronic steering control lock module went out on my car. This seems to be a reoccurring issue with any "W204" 2008/2009 mercedes benz model car. I've documented over a few hundred cases alone on the forums online. This IS a dealership only fix and should be recalled. Basically, security system in the car that lets the key communicate with the ignition system goes out and the car will not start. It's a $1200 fix minimum..

• Jun 17, 2016TN94,000 mi
  Steering · Unknown or other
  My 2008 mercedes AMG C63 had been operating without flaws until recently, I parked, went in the gym to work out for 45 mins. When I came out and tried to start the vehicle, there was no response. Steering wheel locked, wouldn't come out of park. Left me stranded. I have read dozens of complaints on…

  My 2008 mercedes AMG C63 had been operating without flaws until recently, I parked, went in the gym to work out for 45 mins. When I came out and tried to start the vehicle, there was no response. Steering wheel locked, wouldn't come out of park. Left me stranded. I have read dozens of complaints on the mercedes-benz forums about this specific issue happening to other owners of 2008-2009 mercedes C63 sedans. Mercedes has a technical service bulletin listing this as a common occurrence, and the entire steering column lock has to be replaced(usually between $1200-1500). This IS clearly a manufacturer defect, and should be replaced under recall, as it drastically effects the reliability as well as safety of the vehicle, even when not moving. At no fault of the owner, owner will be left stranded anywhere without warning, as no malfunction indicator displays, vehicle just dies suddenly.

• Dec 29, 2013IN67,200 mi
  Exterior lighting
  The passenger tail lamp bulb carrier, ground wire, and connecting plastic harness all melted causing my tail lamps to appear dim and eventually melted to the point the passenger brake lights, rear running lamps, rear passenger turn signal and rear fog lamp all completely quit functioning. I…

  The passenger tail lamp bulb carrier, ground wire, and connecting plastic harness all melted causing my tail lamps to appear dim and eventually melted to the point the passenger brake lights, rear running lamps, rear passenger turn signal and rear fog lamp all completely quit functioning. I contacted my local mercedes benz dealer and they would not fix the problem under warranty or good will even knowing it to be a common problem. I purchased the parts that they claimed have been updated (although they appear to be exactly the same) and had them replaced. Time will tell whether or not this IS a permanent fix to the problem. *tr

• Dec 29, 2013WA31,500 mi
  Electrical system · Exterior lighting

  Rear taillights started smoking. It was all burned out causing rear right taillight to malfunction. *tr

• Feb 11, 2013CA50,000 mi
  Fuel/propulsion system
  2008 C63 amg-every time fill up tank there very strong gas smell even out door. I tracked down smell from under back seat where gas tank IS. Open back seat you will see wet spot from gas leak. This IS extremely dangerous that car can get caught on fire. I research online and found many mercedes…

  2008 C63 amg-every time fill up tank there very strong gas smell even out door. I tracked down smell from under back seat where gas tank IS. Open back seat you will see wet spot from gas leak. This IS extremely dangerous that car can get caught on fire. I research online and found many mercedes has same issue and been told by dealer that it tear and wear, and user responsible for repair. my car IS 2008 C63 AMG, one of top c class model, with 50,000 miles. The gas tank should last much longer than 50,000 mile. This IS unacceptable for mercedes or even any brand. *tr

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Loss of rear lighting assembly

  EA13008Opened Dec 20, 2013Closed May 12, 2014Recall 14V177000
  The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish…

  The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of loss of rear lighting in model year (MY) 2008-2011 Mercedes Benz C-Class vehicles.Complainants alleged that one or both rear lighting assemblies fail to illuminate (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) or illuminate dimly.In some reports, complainants also alleged that the failure was accompanied by a burning smell emanating from the trunk of the vehicle.When examined, these vehicles showed evidence of overheating at the lighting assembly harness connector, including damaged (blackened) wiring and plastic.The rear lighting failures typically involved one side of the vehicle however in some cases both assemblies failed (although probably not simultaneously).ODI identified 5 fire and one injury allegations during the course of this investigation.Two fires occurred while the vehicles were parked.One originated in the vicinity of the driver?s side light assembly where the fire and associated damage was confined to the trunk area, and the fire self extinguished due to oxygen starvation.As a result of the fire, the vehicle was repurchased by Mercedes and salvaged.The second fire originated on the passenger's side and required fire department response to extinguish; the fire damaged the tail light and surrounding body panels as well as the trunk area and wiring.The vehicle was repaired and returned to service.Two firesoccurred while the vehicle was being driven.In the first instance, the driver detected an odor and pulled over to observe smoking and a small flame at the lighting assembly wiring in the trunk.The owner was able to extinguish the fire before any significant damage occurred.In the second instance, the driver smelled smoke, pulled over, and opened the trunk to find smoke and sparks emanating from the forward facing side of the tail light.The driver was able to extinguish the sparks and drive the vehicle to the dealer. A fifth fire was reported by a fleet manager who observed a vehicle with fire damage originating near one of the tail light assemblies.The injury incident occurred when a technician burned their hand while diagnosing a failed light.The technician touched the tail light wiring which was hot enough to burn him although the injury did not require medical attention.On April 10th, 2014, Mercedes notified ODI that it would conduct a safety recall to remedy the rear light assemblies in approximately 252,867 MY 2008 - 2011 C-Class vehicles including the C300, C350 and C63 AMG models.Each rear light assembly has separate bulbs that act as brake, tail lamp, backup and turn signal indicators.The bulbs are mounted in a bulb carrier which uses a common electrical ground circuit at the harness connection.According to Mercedes, oxidation due to the use of dissimilar metals on the harness and bulb carrier electrical connectors can result in increased resistance and a subsequent dimming or loss of lighting function.The heat caused by the increased resistance/oxidation can also lead to the melting of the surrounding plastic, or in some cases, present a fire hazard.In conducting recall 14V-171, Mercedes dealers will inspect the left and right bulb carriers and harness connectors for the presence of dissimilar electrical connectors and/or evidence of related thermal damage; affected bulb carriers and/or harness connectors will be replaced free of charge.Mercedes notes that service replacement bulb carriers produced from January 2012 eliminate the dissimilar metal condition and that these bulb carriers will not requ

• Loss of rear tail light functionality

  PE13026Opened Jul 11, 2013Closed Dec 30, 2013
  ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed…

  ODI initially received 21 reports of rear light assembly failure due to a melted electrical connector or housing.Since opening the initial , ODI has received a total of 114 complaints reflecting an ongoing and increasing trend.In each report, one or both rear light assemblies fail completely (i.e., all lights housed within the assembly extinguish, including the stop, tail, and turn signal functions) when the electrical ground connection is compromised as a result of high resistance and subsequent thermal over-heating.According to Mercedes-Benz, the over-heating of the ground wire is caused by corrosion between the connectors in the ground circuit to the tail light.ODI is aware of a total of 5 reports alleging fire including one injury allegation as a result of this issue.Analysis of subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.As a result of the evidence presented, this investigation has been upgraded to EA13-008.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10235983Daimler AG (DAG) has decided that a supplier production error in the SRS control unit could lead to a failure of the SRS control unit. This malfunction of the SRS control unit would illuminate the SRS warning lamp and subsequently deactivate the SRS components. Additionally, in the event one specific electrical connection is interrupted, several SRS components could inadvertently deploy, increasing the risk for injury.
• 10235978Recall Campaign announcement for Takata driver airbags.
• 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
• 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
• 10205265Outside mirror fogged.
• 10205239"Anti-theft protection activated".
• 10205237The COMAND unit does not start or the display remains dark.
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10205225Headlamps fogged.
• 10205150Engine sound change after recent software updates.
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
• 10181124Harsh engagement when changing gear range from P to D or R
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167560Fault message in display - Right rear turn signal light inoperative
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
• 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
• 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
• 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
• 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
• 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
• 10167510The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
• 10167489Noise: A rattling noise may be heard from the area of the chain drive for approx. 2-5 seconds after engine start. And/or: Fault code entries in engine control unit: SIM271DE20: P001177 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001762 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001192 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001195 The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001477 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. P001492 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The function or the instruction is faulty. P001495 The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The mechanical setup is not OK. P001600 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. P001662 The position of the intake camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft. The signal comparison is faulty. P001700 The position of the exhaust camshaft (cylinder bank 1) is implausible in comparison with the position of the crankshaft.

Every Mercedes Benz C63 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.