2000 Mercedes Benz CL500

Recalls

1 recall names the 2000 Mercedes Benz CL500. Newest first.

• Exterior lighting › Headlights › Switch

  Aug 1, 2001NHTSA 01V247000613 vehicles

  Vehicle description: passenger vehicles. these vehicles fail to conform with the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment." when the low beam headlamps are activated, the xenon lamps are aimed to illuminate the road surface. in the high beam mode the light from the xenon bulbs are redirected and additional…

  Risk and remedy

  Risk

  Drivers in incoming vehicles may experience increased glare from the high beam lighting which could result in the potential for a crash.

  Remedy

  Dealers will modify the aim of the halogen headlamp bulbs in the high beam mode. owner notification began october 15, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact mercedes-benz at 1-800-367-6372.

  Full recall details →

Owner complaints

What owners report most

1. Suspension3
2. Electrical system2
3. Engine1
4. Interior lighting1

Latest complaints

• Nov 25, 2015OR116,000 miFire
  Suspension

  TL* the contact owns a 2000 mercedes benz cl500. The contact stated that while driving at 60 mph, the suspension system nearly caught fire. The contact stated that there was a considerable amount of smoke coming from the vehicle. The vehicle was taken to a dealer to be diagnosed and repaired. The manufacturer was made aware of the failure. The failure mileage was 116,000.

• Jul 8, 2015NY
  Electrical system
  TL* the contact owns a 2000 mercedes benz cl500. While traveling approximately 40 mph, the instrument cluster failed to work and went completely blank several times. The vehicle was taken to an authorized dealer where it was diagnosed that the instrument cluster needed to be replaced. The contact…

  TL* the contact owns a 2000 mercedes benz cl500. While traveling approximately 40 mph, the instrument cluster failed to work and went completely blank several times. The vehicle was taken to an authorized dealer where it was diagnosed that the instrument cluster needed to be replaced. The contact replaced the fuses multiple times but the failure recurred. The vehicle was not repaired. The manufacturer was notified of the failure and provided no remedy. The failure mileage was not available.

• Sep 23, 2014MA74,000 mi
  Suspension
  TL* the contact owns a 2000 mercedes cl500. The contact stated that while driving at 30 mph, the vehicle dropped to the ground. In addition, the contact stated that the active body control IS too low please stop vehicle warning indicator illuminated. The failure occurred on several occasions. The…

  TL* the contact owns a 2000 mercedes cl500. The contact stated that while driving at 30 mph, the vehicle dropped to the ground. In addition, the contact stated that the active body control IS too low please stop vehicle warning indicator illuminated. The failure occurred on several occasions. The vehicle was taken to a dealer where it was diagnosed that fluids was leaking through seals of the vehicle. As a result, the abc high pressure hose and the hydraulic pump needed to be replaced. The vehicle was repaired but the failure recurred. The manufacturer was notified of the failure. The failure mileage was 74,000. The vin number was unavailable.

• Jul 8, 2013MI96,000 mi
  Engine
  TL* the contact owns a 2000 mercedes benz cl500. The contact stated that while driving 80 mph, the vehicle overheated. The contact stopped and restarted the vehicle however, the vehicle later stalled. The vehicle was taken to a private mechanic, who stated that the vehicle overheated and the crank…

  TL* the contact owns a 2000 mercedes benz cl500. The contact stated that while driving 80 mph, the vehicle overheated. The contact stopped and restarted the vehicle however, the vehicle later stalled. The vehicle was taken to a private mechanic, who stated that the vehicle overheated and the crank shaft position sensor was damaged. The vehicle was not repaired. The failure was reported to the manufacturer. The failure and current mileage was 96,000.

• Jun 25, 2010NJ15,000 miFire
  Suspension › Rear
  TL* the contact owns a 2002 mercedes benz cl500 (n/a). While traveling at 55 mph, the contact heard a loud, unusual pop coming from the rear of the vehicle. Within seconds, there was smoke coming from the vehicle rear. The vehicle was taken to a local mechanic where the contact was informed that…

  TL* the contact owns a 2002 mercedes benz cl500 (n/a). While traveling at 55 mph, the contact heard a loud, unusual pop coming from the rear of the vehicle. Within seconds, there was smoke coming from the vehicle rear. The vehicle was taken to a local mechanic where the contact was informed that the suspension hose had failed. The vehicle was taken to a second mechanic where the suspension hose was replaced. The failure mileage was 78,000 and the current mileage was 90,000.

• Oct 16, 2006WA54,118 mi
  Electrical system · Interior lighting
  Dt*: the contact stated the instrument cluster did not illuminate properly on two occasions. the vehicle was taken to the dealer, who determined the instrument cluster needed to be replaced. there was a nhtsa recall #06v028000 regarding interior lighting. the vehicle was not included in the…

  Dt*: the contact stated the instrument cluster did not illuminate properly on two occasions. the vehicle was taken to the dealer, who determined the instrument cluster needed to be replaced. there was a nhtsa recall #06v028000 regarding interior lighting. the vehicle was not included in the recall due to the vin. the vehicle was not repaired due to the part availability. the contact has been waiting over a month for the part to be available for repair.*ak updated 10/31/2006 - the instrument cluster blacked out plus there were additional electrical faulures. the new cluster that the dealer cclamed was needed was not covered under recall. *nm

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Engine crankshaft pulley failure

  PE03058Opened Dec 17, 2003Closed Apr 22, 2004
  The office of defects investigation (odi) opened this preliminary evaluation to investigate allegations of engine crankshaft pulley harmonic balancer failure that could result in loss of power-steering assist.odi has received a total of 546 non-duplicative reports that allege engine crankshaft pulley harmonic balancer…

  The office of defects investigation (odi) opened this preliminary evaluation to investigate allegations of engine crankshaft pulley harmonic balancer failure that could result in loss of power-steering assist.odi has received a total of 546 non-duplicative reports that allege engine crankshaft pulley harmonic balancer failure on all mercedes-benz vehicles using the subject component.the subject component failures are progressive in nature and only a small percentage of the complaints and warrant claims involved a failure that had progressed far enough to effect power steering performance (6 of 55 odi complaints reference increased steering effort).there have been no crashes or injuries related to the alleged defect.a safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.accordingly, this investigation IS closed.the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.the agency will take further action if warranted by the circumstances.see summary report attached for further detail.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10181124Harsh engagement when changing gear range from P to D or R
• 10181123Harsh engagement when changing gear range from P to D
• 10167545During disengagement from D to N and/or from R to N some slight jolting could be experienced.
• 10166982During disengagement from D to N and/or from R to N some slight jolting could be experienced.
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
• 10166099Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
• 10166091Front seat backrest locks at folded-forward position
• 10165844Possible minor leakage at described components or oil transfer from assembly plant.
• 10165839Shift quality complaints on TRANSMISSION 722.9 (7G-TRONIC and 7G-TRONIC PLUS)
• 10151959Seat belt extender toothed rack sluggish or makes noises
• 10135635Message in instrument cluster "ESP Malfunction - Service Required"
• 10044181Xentry: rattling/thumping noises from the area of the steering on rough roads or when driving over road undulations. No model years given. Also included models 168 and 172.
• 10037917Mercedes-benze: there IS a leakage at the press-fit sleeve of a pulsation damper. This IS caused by high heat entering the system or tension in the line.
• 10028686Mercedes: air matic visit workshop displayed within instrument cluster. Models 164, 211, 219, 221 and 251. Included 4matic, AMG (compressor) AMG, bluetec and wagon. Model years unknown. Updated 9/18/09.
• 10028684Mercedes: esp service required displayed in instrument cluster. Also includes 4matics, bi turbos and kompressors. Models 215 and 220. Model years unknown.
• 10028665Mercedes: warning message right low beam- check bulb; or left low beam-check bulb in instrument cluster. Due to the fact that the xenon burner may not be ignited on first attempt due to tolerances in ignition voltage. Model years unknown.
• 10028627Mercedes: display in instrument cluster "air suspension" or "abc service required" IS displayed in the instrument cluster, the engine wiring harness may have been damaged by the wiper linkage. Models 215.3 and 220. Model years unknown.
• 10028626Mercedes: the vehicle's suspension level randomly lowering while driving and/or rapid sporadic level changes shortly after stopping the vehicle, replace the body acceleration sensors. Models 215.3, 220, and 230. Model years unknown.
• 10020460Play in the rack and pinion steering system. Models 203, 209, 210, 211, 215, 220, 230. Mercedes benz. Updated 5/13/09.
• 10016687Abc visit workshop displayed in instrument cluster and hydraulic fluid leakage. Updated 5/14/09. Models 215, 220 and 230. Model years unknown.
• 10016670Mercedes: the fuel level indicated in the instrument cluster does not match the actual fill level. This may be caused by a fault in the fuel level sensor function chain: hydraulic and electrical lines and their connections, rear sam or instrument cluster. Updated 2/23/09. Updated 9/18/09. Model years unknown.

Every Mercedes Benz CL500 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.