2018 Mercedes-Benz E 300
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › E 300 › 2018
These records cover every 2018 Mercedes-Benz E 300. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2018 Mercedes-Benz E 300. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 C300, C300 Coupe, CLS450, E450 Coupe and S450, 2017-2019 E300, 2018 E400 Coupe, E400 Stationwagon, and 2018-2019 S560 vehicles that have previously had the instrument cluster replaced. The software in the replaced instrument cluster may cause the seat belt warning system to not operate properly…
Risk and remedy
Risk
Without the audible tone and blinking warning light to remind the front seat occupants that their seat belts are not buckled, they may forget to buckle their seat belt, increasing their risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will update the instrument cluster software, free of charge. The recall began September 8, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020080015.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2018 E400 Wagon 4MATIC, E400 4MATIC, E43 AMG 4MATIC, 2018-2019 E63S AMG 4MATIC Wagon, E63 AMG 4MATIC Wagon, E300, E300 4MATIC, GLC63S Coupe AMG 4MATIC, 2019 CLS450, CLS450 4MATIC, CLS53 AMG 4MATIC, E450 Wagon, E53 AMG 4MATIC, GLC300, GLC63 AMG Coupe 4MATIC, G550 4MATIC, G63 AMG, GLC300 Coupe 4MATIC…
Risk and remedy
Risk
The electric PRE-SAFE®-function and the seat belt pretensioners may not deploy during a crash, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the front seat belt buckles, replacing them as necessary, free of charge. The recall began March 13, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020020017.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 Mercedes Benz C300, 2017-2019 C300 Cabrio, C300 Coupe, C63 Cabrio, 2015 C63S AMG, 2018-2019 C300, C350e, C63 AMG, C63S AMG Cabrio, 2018 C63 AMG Cabrio, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, E300, E400 Cabrio, E400 Coupe, 2019 CLS450, E450 Cabrio, and E450 Coupe rear-wheel drive vehicles. A…
Risk and remedy
Risk
A car that cannot be properly steered has an increased risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019080012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 Mercedes-Benz C300 4Matic Coupe, C300 4Matic Cabrio, E300, E300 4Matic, C300, C300 4Matic, C300 Coupe and C300 Cabrio vehicles. The cover for the starter battery may not cover the live positive electrical wire, and in certain crashes, the vehicle's strut brace may deform and short circuit the battery.
Risk and remedy
Risk
If the battery is shorted, the emergency door unlocking would be deactivated for an outside responder and the short circuit could increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will replace the positive pole cover, free of charge. The recall began November 27, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018110002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 Mercedes-Benz E300, E300 4Matic, E43 AMG 4Matic, E400 4Matic, E63S AMG 4Matic+, and 2019 CLS450 4Matic vehicles. The Occupant Classification System (OCS) may not be properly calibrated, resulting in the front passenger air bag not being deactivated if a child seat is in the front seat.
Risk and remedy
Risk
If a child seat is in the front seat and the passenger air bag is not deactivated, in the event of a crash, it can increase the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger seat cushion, free of charge. The recall began November 26, 2018. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
32 complaints1 involved a crash2 injuries
What owners report most
Latest complaints
- Power train
The contact owns a 2018 Mercedes Benz E Class. The contact stated that while driving stopped at a residential gate, the gear was shifted and skipped from g1 to g3., shifting itself to neutral. In another incident, when at a stop light or stop sign, the vehicle stalled. The vehicle was taken to the…
The contact owns a 2018 Mercedes Benz E Class. The contact stated that while driving stopped at a residential gate, the gear was shifted and skipped from g1 to g3., shifting itself to neutral. In another incident, when at a stop light or stop sign, the vehicle stalled. The vehicle was taken to the dealer for a recall repair for software update however the issue that was experienced with the vehicle stalling was not diagnosed or repaired. The contact stated that he thought the recall had to do with the issue he was experiencing but was informed by the dealer that it was a separate issue. The manufacturer was notified of the issue. the approximate failure mileage was 112,000.
- Engine
Variable Valve Timing Camshaft KNOWN DEFECT rendering the car unusable at only 100K miles.
- Air bags
The contact owned a 2018 Mercedes-Benz E300. The contact stated that while driving 30 MPH, another vehicle leaving the parking lot pulled in front of the contact's vehicle, and the contact's vehicle crashed into the side of the other vehicle. The air bags failed to deploy. The contact's face and…
The contact owned a 2018 Mercedes-Benz E300. The contact stated that while driving 30 MPH, another vehicle leaving the parking lot pulled in front of the contact's vehicle, and the contact's vehicle crashed into the side of the other vehicle. The air bags failed to deploy. The contact's face and chest hit the steering wheel. The contact sustained soreness on the face, and from the shoulders down to the lower back and legs. The contact was currently dragging one leg while walking. The contact had received dental and medical assistance. Additionally, the contact underwent an MRI. The contact was informed that the third and fourth vertebrae were damaged. The vehicle was towed and totaled. A police report was filed. The dealer was notified of the failure. The manufacturer was notified of the failure and informed the contact that the vehicle operated as designed. The failure mileage was unknown.
- Electrical system · Engine · Power train
The car did not give any warning before this issue came about. A matter of fact when I took it to the mechanic they were unable to do a diagnostic test because there were no error messages and check engine light never came on. After taking it to the dealership they were able to check the history…
The car did not give any warning before this issue came about. A matter of fact when I took it to the mechanic they were unable to do a diagnostic test because there were no error messages and check engine light never came on. After taking it to the dealership they were able to check the history and saw that the error code P061b00 shows that the clutch position switch module needs to be replaced. While driving in traffic the car went into N (neutral) and wouldn’t not go back in D (drive). It took several minutes of me trying to change gears but it eventually went into P (park). The vehicle is unable to change gears sometimes and this is unsettling because the safety of myself, my children and others is affected if I’m driving and the car goes into neutral all of a sudden with no warning or goes into park and is unable to move. This occurred several times within a two week span while my children were in the car and this could have ended very differently. I took it to a certified mechanic who provided an explanation based on the error code received and stated that this was a huge safety issues that needed to be addressed.
- Unknown or other
Sunroof shattered.
- Engine
Check Engine Light, running fault code P052E71 - needs software update for N3/10 Engine control unit.
- Seat belts
Passenger seatbelt does not latch to the buckle. Therefore I am unable to have passengers in my vehicle. And when I do it becomes a huge safety issue. No mechanic can seem to figure out what is wrong with it.
- Electrical system · Seats · Wheels
In April 2022, I purchased a 2018 Mercedes-Benz E300 4MATIC from CarMax in Tinley Park, Illinois. After the purchase, I discovered several unresolved issues that compromised the vehicle's safety and reliability. Key components, including the battery and alternator, were defective. Mercedes-Benz…
In April 2022, I purchased a 2018 Mercedes-Benz E300 4MATIC from CarMax in Tinley Park, Illinois. After the purchase, I discovered several unresolved issues that compromised the vehicle's safety and reliability. Key components, including the battery and alternator, were defective. Mercedes-Benz confirmed the battery had not been replaced since 2018, despite CarMax’s assurance that it was new. This defect contributed to electrical system malfunctions, affecting the vehicle’s performance. Additionally, CarMax conducted substandard repainting on the backseat. The peeling paint transferred to my clothing while driving, causing financial losses and embarrassment. Issues with the rims were also mishandled, further compromising the vehicle's quality. CarMax failed to disclose unresolved safety recalls affecting critical vehicle systems, and their inadequate repairs and omissions put my safety at risk. These defects have caused significant inconvenience, financial loss, and concerns about the vehicle’s reliability. Despite requests, CarMax has not adequately addressed these issues. CarMax acquired the vehicle in 2021 from its first owner, who had purchased it in 2018. At the time of acquisition, the vehicle had been driven 45,069 miles. When I purchased it in 2022, the odometer read 57,925 miles, indicating that CarMax operated the vehicle for 12,856 miles. This period of use was later discovered to involve its usage as a loaner vehicle, a fact not disclosed during the transaction. Upon taking possession of the vehicle, I became aware of several safety issues that were not disclosed, including unresolved recalls affecting key components of the vehicle. Despite the critical nature of these recalls, CarMax sold the vehicle without addressing these defects or informing me of their existence. Omission of Material Safety Information: CarMax failed to disclose the vehicle’s use as a loaner car and any associated wear and tear, which likely exacerbated the safety risks.
- Engine
added information: the issue is the piston, it went off due to a bad part. Mercedes Benz knew about the issue with the type of engine M247. there is a class action lawsuit pending. But I'm reporting this because i didn't know and it happened to me just a month out of warranty. Now, the dealership…
added information: the issue is the piston, it went off due to a bad part. Mercedes Benz knew about the issue with the type of engine M247. there is a class action lawsuit pending. But I'm reporting this because i didn't know and it happened to me just a month out of warranty. Now, the dealership is asking me to pay for the labor. the dealership is House Of Imports in Buena Park. This has to do with the piston failure.
- Power train
Vehicle went into limp mode at 83,000 miles and it was due to the electronic valve body failing within the transmission. Dealership mentioned it shouldn’t happen in a vehicles lifetime, this includes maintenance at the right interval (60,000 miles), which mine was. I was quoted roughly $3,800 by the dealership but after speaking with corporate it was brought down to $2,600.
- Power train
The contact owns a 2018 Mercedes-Benz E300. The contact stated while attempting to shift into drive, the transmission independently shifted to neutral. The contact attempted several times to shift into drive however, the transmission failure persisted. The vehicle was towed to the local dealer. The…
The contact owns a 2018 Mercedes-Benz E300. The contact stated while attempting to shift into drive, the transmission independently shifted to neutral. The contact attempted several times to shift into drive however, the transmission failure persisted. The vehicle was towed to the local dealer. The vehicle was diagnosed with transmission failure. The vehicle was not repaired. The manufacturer was notified on the failure. The approximate failure mileage was 154,000.
- Electrical system
The back-up camera failed while in the middle of reversing. Screen went completely black and unresponsive. Putting the car in Park then back to Reverse didn't work, screen still black. Tried turning off the car and turning it back on, screen still black and no back-up camera when I put the car…
The back-up camera failed while in the middle of reversing. Screen went completely black and unresponsive. Putting the car in Park then back to Reverse didn't work, screen still black. Tried turning off the car and turning it back on, screen still black and no back-up camera when I put the car in Reverse. I tried turning on / off the infotainment system and no change, screen still black. Later in the day when I got back in the car, the screen came up MUCH slower than usual, but did eventually come back up. This has happened multiple times and I've taken it to the dealer multiple times for this, but they've not been able to fix it.
- Fuel/propulsion system · Power train
Mercedes Benz use low quality PCV regulator valve , it is a common failure problem, warranty will not be covered, Benz sells part replacement for around 350 USD and it require about 2000 in labor to be fixed on average
- Electrical system · Steering · Unknown or other
When taking curves the vehicle is making a cracking noise but, mechanic said they don’t see anything. My W213 Mercedes Benz E300 just like all other Mercedes is have a “Crankcase” issue, it failed the engine keep revving but, not catching speed. I’ve seen multiple Mercedes is having that issues…
When taking curves the vehicle is making a cracking noise but, mechanic said they don’t see anything. My W213 Mercedes Benz E300 just like all other Mercedes is have a “Crankcase” issue, it failed the engine keep revving but, not catching speed. I’ve seen multiple Mercedes is having that issues and it’s very common. My vehicle computer communication system failed to communicate with the key sometimes won’t start and will run out of power overnight mainly happen during winter times and when it rains.
- Electrical system · Engine
According to the Mersedes dealer it is Engine Harness it is possible manufacture defect. Car has only 38900 miles on it.
- Engine
yellow check engine light came on and a few days later the car stalled on the road potentially causing an accident. took it to a shop and it has a p052e (crankcase valve issue), then took it to mercedes and theyve confirmed that oil has been leaking and it needs a new cvp ($3000) AND oil has leaked…
yellow check engine light came on and a few days later the car stalled on the road potentially causing an accident. took it to a shop and it has a p052e (crankcase valve issue), then took it to mercedes and theyve confirmed that oil has been leaking and it needs a new cvp ($3000) AND oil has leaked into the engine harness ($4000) but a few other indie shops have mentioned that id probably also have to replace the thermostat because thats usually damaged as well. You can google this issue and see that its insanely common, dangerous, and a huge financial burden on mercedes owners. There should be an immediate recall. See the inspection here: https://app.mykaarma.com/service-cart/mpi/8RlVgZhzCNsvpezrI1ZEEtxKAPluMxrUUivaOkycfRg/detail
- Engine
Recurrent crankshaft ventilation valve failures. Replaced 14 months ago and has failed again. This is a common and known issue with vehicles in E class from 2017 through 2019 and Mercedes has not issued a recall. Perhaps because it costs $3500 to replace it if out of warranty. Entire system replaced Feb 17, 2022 and has failed again (April 6th, 2023)
- Unknown or other
While the vehicle was parked, at approximately 6:15 pm on June 11, 2022 while I was retrieving my iPod that was on the cupholder of my wife’s car, I got cut on the back of my right hand by the chrome plating lining the top part of the cupholder. The cut was painful and was one centimeter long.…
While the vehicle was parked, at approximately 6:15 pm on June 11, 2022 while I was retrieving my iPod that was on the cupholder of my wife’s car, I got cut on the back of my right hand by the chrome plating lining the top part of the cupholder. The cut was painful and was one centimeter long. After I got cut I noticed that the chrome plating around the cupholder was peeling off and was sharp to the touch. The peeling off was mainly on the middle to the left-hand side of the center console cupholder, it is razor sharp and very dangerous. Please warn other drivers about this danger. It would be especially dangerous if someone gets cut while driving the car. It seems other Mercedes Benz owners have had this issue too: Here - https://mbworld.org/forums/c-class-w205/724605-interior-chrome-trim-flaking.html And here - https://mbworld.org/forums/w213-amg/810641-ashtray-cup-holder-trim.html This problem is similar to one I had experienced years ago on the door handle of a Hyundai Sonata I used to own, with peeling sharp chrome edge on interior drivers door handle - https://www.autoblog.com/amp/2009/05/26/hyundai-recalling-over-91-000-sonata-sedans-due-to-sharp-chro/
- Visibility › Sun/moon roof assembly
The contact owns a 2018 Mercedes-Benz E300. The contact stated that while driving at an undisclosed speed, wind was entering through the passenger’s side sunroof. There were no warning lights illuminated. The vehicle was taken to the local dealer where they informed the contact that the vehicle was…
The contact owns a 2018 Mercedes-Benz E300. The contact stated that while driving at an undisclosed speed, wind was entering through the passenger’s side sunroof. There were no warning lights illuminated. The vehicle was taken to the local dealer where they informed the contact that the vehicle was working as designed. The vehicle was not repaired. The manufacturer was not notified. The failure mileage was approximately 34,000.
- Engine · Steering · Suspension
Mb 2018 E300 would stop with me in the middle of traffic the stop and start system malfunctions and dealership refused to fixed the problem until I almost got killed. Car stop in the middle of traffic around (nov 2020 off commercial blvd fort lauderdale fl between 4 to 6PM rainy day rush hour…
Mb 2018 E300 would stop with me in the middle of traffic the stop and start system malfunctions and dealership refused to fixed the problem until I almost got killed. Car stop in the middle of traffic around (nov 2020 off commercial blvd fort lauderdale fl between 4 to 6PM rainy day rush hour about to make a right turn to get on I95 and care died on me and I had to wait 3 yours because onstar button wasn't working and had to call tow using my phone ) I been having issues starting back up and other problems with the pistines in the engine and car finally breaks down and needs new engine feb 2 mercedes never honors their warranty and fixed my issue . One driver with 2018 E300 mercedes benz like mine after 23K miles needs a new engine also . Below I past the link to the forum with other mb customers complaining about the safety issues of their e-class mb all of which experience familiar engine and car start up failure. https://mbworld.org/forums/e-class-w213/798120-2018-mercedes-w213-e300-needs-new-engine-23k-miles-2.html confirmation code: [xxx] date and time: jan 6, 2021 9:00:00 am vehicle: 2018 mercedes-benz E300 vin: [xxx] advisor: [xxx] arrangement: loaner vehicle repair services: engine performance concern (hesitation, lack of power, poor mileage, etc.) ' customer states that the vehicle stalls at regular period confirmation code: [xxx] date and time: nov 25, 2020 10:00:00 am vehicle: 2018 mercedes-benz E300 vin: [xxx] advisor: [xxx] arrangement: loaner vehicle repair services: tell us more ' client states the vehicle IS having issues when she turn the car on, there are some weird noises coming fron engine information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr
- Latches/locks/linkages › Doors › Latch
TL* the contact owns a 2018 mercedes-benz E-300. The contact stated while the vehicle was stationary, the front driver's and passenger's doors failed to remain open. The contact stated that the doors closed independently. The contact stated there was no warning light illuminated. The vehicle was…
TL* the contact owns a 2018 mercedes-benz E-300. The contact stated while the vehicle was stationary, the front driver's and passenger's doors failed to remain open. The contact stated that the doors closed independently. The contact stated there was no warning light illuminated. The vehicle was taken to calstar motors (700 s brand blvd, glendale, ca 91204) where it was diagnosed however, nothing was repaired or replaced. The contact related the failure to the door hinges. The vehicle was not repaired. The manufacturer was informed of the failure but provided no assistance. The failure mileage was approximately 18,034.
- Electrical system · Engine · Wheels
TL* the contact owns a 2018 mercedes-benz E-300. The contact stated that while driving at 80 mph, the vehicle vibrated uncontrollably. The contact also stated that the vehicle experienced unknown electrical and engine failures. On numerous occasions the vehicle was taken to mercedes-benz of seattle…
TL* the contact owns a 2018 mercedes-benz E-300. The contact stated that while driving at 80 mph, the vehicle vibrated uncontrollably. The contact also stated that the vehicle experienced unknown electrical and engine failures. On numerous occasions the vehicle was taken to mercedes-benz of seattle located at (2025 airport way s, seattle, wa 98134) however, the mechanic was unable to duplicate the failure. The contact was also concerned that there was carbon monoxide leaking into the vehicle after the contact was diagnosed with carbon monoxide poisoning. The vehicle was taken to the same dealer for another diagnostic test to be performed. While inspecting the vehicle, the two front tires experienced blowouts. The manufacturer was notified on numerous occasions of the failures but offered no assistance. The approximate failure mileage was 25,000.
- Steering
TL* the contact owns a 2018 mercedes-benz E300. The contact received a recall notification for nhtsa campaign number: 18v850000 (steering). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called mercedes-benz of georgetown (7401 I-35…
TL* the contact owns a 2018 mercedes-benz E300. The contact received a recall notification for nhtsa campaign number: 18v850000 (steering). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called mercedes-benz of georgetown (7401 I-35, georgetown, tx 78626, (512) 930-6150) and was informed that the parts were not available. The vehicle was not diagnosed or repaired. The manufacturer was contacted and did not assist. The contact had not experienced a failure. Vin tool confirms parts not available.
- Steering
TL* the contact owns a 2018 mercedes benz E300. The contact received a recall notification for nhtsa campaign number: 18v850000 (steering) and stated that the manufacturer had exceeded the reasonable amount of time to repair the vehicle. The dealer mercedes benz of sarasota (4754 clark rd…
TL* the contact owns a 2018 mercedes benz E300. The contact received a recall notification for nhtsa campaign number: 18v850000 (steering) and stated that the manufacturer had exceeded the reasonable amount of time to repair the vehicle. The dealer mercedes benz of sarasota (4754 clark rd, sarasota, fl 34233) confirmed that parts were not available to perform the recall repair. The manufacturer was notified of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Forward collision avoidance · Service brakes
The car activated its emergency braking function unexpectedly. I was driving on a community college campus street. no cars no bags no wind no anything at about 20-25 mph. all clear air temp 83 degrees f. sunshine. No adverse conditions. car suddenly slammed on brakes without any warning or…
The car activated its emergency braking function unexpectedly. I was driving on a community college campus street. no cars no bags no wind no anything at about 20-25 mph. all clear air temp 83 degrees f. sunshine. No adverse conditions. car suddenly slammed on brakes without any warning or reason whatsoever. seatbelt tightened per procedure. fortunately there's was no one behind me to rear end me. took car straight to dealer. Scanned for codes. none found. car IS performing as designed. no. there are other documented cases on line in the mercedes forums. pleas investigate.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009025Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005276Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2018 C300 and 2016-2018 GLC300 and E300 vehicles. Model year 2015-2017 C300 | Model year 2019 GLC300 and E300 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required.
- 11003218Complaint Complaints about shift quality in vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2. Cause If the shift adaptation is not performed as described under "Remedy", the adaptation values may not be saved correctly under certain circumstances. Remedy In vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2, it must be ensured that the adaptation of the shifts is performed only as described below. Acceleration upshifts may only be adapted in transmission mode "S" Acceleration downshifts may only be adapted in transmission mode "S" Coast down shifts may only be adapted in transmission mode "E"
- 11000623Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model year 2015-2018 vehicles. Model year 2019 (Except model 172 and hybrid variants) Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
- 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10238424In the MBUX weather app, the temperature is displayed in the wrong unit (Fahrenheit instead of C, or vice versa). Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)
- 10233783Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
- 10227148Complaint The trunk lid is not latching into the closed position with the help of the trunk lid power closing function after the electric closing process. There is a loud rattling from the trunk or from the trunk lid power closing unit (M14/31). Cause Under Analysis Remedy Please create a PTSS case to MBUSA before attempting repair on the vehicle
- 10222481Complaint Customer states after a bus sleep the SiriusXM category changes from "My Favorites" to "All Stations" or a different category. Sometimes, the "My Favorites" category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be updated once the software is released.
Every Mercedes-Benz E 300 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.