2023 Mercedes-Benz E 450
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › E 450 › 2023
These records cover every 2023 Mercedes-Benz E 450. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2023 Mercedes-Benz E 450. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 CLS450, E450, E450 All-Terrain, AMG E53, AMG GT43, AMG GT53, and 2021 AMG CLS53 vehicles. The 48-volt ground cable connection located in the engine compartment may not be tightened properly and may result in the ground cable overheating.
Risk and remedy
Risk
An overheated ground cable increases the risk of a fire.
Remedy
Dealers will inspect the 48-volt ground cable connection and repair it as necessary, free of charge. Owner notification letters were mailed March 22, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024MMNNNN.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2024 GLE, GLS, C-Class, E-Class, S-Class, SL, GLC, CLS, AMG GT, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, causing a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 28, 2024. Owner notification letters will be mailed in phases, on February 23, 2024, April 19, 2024, June 28, 2024, August 9, 2024, October 1, 2024, and December 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 23V-445.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023 E450, E350, AMG E63 S, AMG E53, CLS450, AMG GT53, and AMG GT43 vehicles. Due to a software error, the exit warning system audio and visual warnings may fail to alert occupants about approaching vehicles.
Risk and remedy
Risk
Failure to alert occupants of an approaching vehicle can increase the risk of a crash or injury.
Remedy
Dealers will update the exit warning system software, free of charge. Owner notification letters were mailed September 8, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023080005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Owner complaints
17 complaints
What owners report most
Latest complaints
- Engine
The contact owns a 2023 Mercedes-Benz E-Class. The contact stated while driving at an undisclosed speed, the engine seized. The contact stated that the failure occurred while making a left turn. In addition, a malfunction error message illuminated. The contact stated while attempting to start the…
The contact owns a 2023 Mercedes-Benz E-Class. The contact stated while driving at an undisclosed speed, the engine seized. The contact stated that the failure occurred while making a left turn. In addition, a malfunction error message illuminated. The contact stated while attempting to start the vehicle, the vehicle failed to start with the push to start. However, the vehicle did start using the key fob. The vehicle was taken to the dealer, however the failure was not duplicated. The manufacturer was not made aware of the failure. The failure mileage was approximately 25,000.
- Electrical system · Vehicle speed control › Cruise control
The contact owns a 2023 Mercedes-Benz E450. The contact stated that while driving at various speeds with the cruise control activated, a yellow "Active Lane Keeping Assistance is Inoperable" message was displayed, followed by a red "Emergency Braking to Begin" message displayed on the instrument…
The contact owns a 2023 Mercedes-Benz E450. The contact stated that while driving at various speeds with the cruise control activated, a yellow "Active Lane Keeping Assistance is Inoperable" message was displayed, followed by a red "Emergency Braking to Begin" message displayed on the instrument panel. To prevent the failure, the contact immediately deactivated the cruise control. The dealer was notified about the failure on several occasions, and two separate cases were filed with the manufacturer. The dealer replaced the steering wheel, replaced several fuses, and performed several software updates to correct the failure under warranty; however, the failure persisted after each repair. The vehicle was not repaired. The failure mileage was approximately 15,500.
- Tires · Tires › Pressure monitoring and regulating systems
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if…
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if I were driving a little faster and fortunately there was no other damage to the car or other persons. In each case, I hit a small pothole, and the tire blew out, flat to the ground. Because these are run flat tires, on the first 2 incidents I was able to drive home and to the dealer for tire repair/replacement. The third one was so bad that I could not drive all the way home and had to get towed. But all 3 incidents were scary and dangerous because of the sudden blowouts. The tires were not repairable and had to be replaced. I believe that the Mercedes Tire inflation instructions is unsafe and they should put more air in the tires to protect from the rim cutting into the tire when hitting a pothole. The driver's door "B" pilar placard says the "cold tire pressure: Front 41 psi Rear 47 psi". Mercedes repair shop inflates the tires according to the Fuel Filler Door decal that says " Front 36 psi, Rear 36 psi." That is a big difference in pressure -- as much as possible 11 psi under pressure. I believe these run flat tires failed because of too low of tire pressure when hitting the pothole. If the tires were inflated with the higher pressures as on the door pilar, the wheel rim would not have been able to cut into and through the tire wall because the higher tire pressure would prevent the impact of the rim cutting through the tire sidewall. I believe this a serious safety issue and Mercedes should be inflating this type run flat MOE tires to a much higher pressure and should not use the low-pressure instructions that are on the fuel door label. There should be a recall and repair instructions to increase run flat tire pressure on Mercedes E class vehicles.
- Tires · Tires › Pressure monitoring and regulating systems
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if I…
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if I were driving a little faster and fortunately there was no other damage to the car or other persons. In each case, I hit a small pothole, and the tire blew out, flat to the ground. Because these are run flat tires, on the first 2 incidents I was able to drive home and to the dealer for tire repair/replacement. The third one was so bad that I could not drive all the way home and had to get towed. But all 3 incidents were scary and dangerous because of the sudden blowouts. The tires were not repairable and had to be replaced. I believe that the Mercedes Tire inflation instructions is unsafe and they should put more air in the tires to protect from the rim cutting into the tire when hitting a pothole. The driver's door "B" pilar placard says the "cold tire pressure: Front 41 psi Rear 47 psi". Mercedes repair shop inflates the tires according to the Fuel Filler Door decal that says " Front 36 psi, Rear 36 psi." That is a big difference in pressure -- as much as possible 11 psi under pressure. I believe these run flat tires failed because of too low of tire pressure when hitting the pothole. If the tires were inflated with the higher pressures as on the door pilar, the wheel rim would not have been able to cut into and through the tire wall because the higher tire pressure would prevent the impact of the rim cutting through the tire sidewall. I believe this a serious safety issue and Mercedes should be inflating this type run flat MOE tires to a much higher pressure and should not use the low-pressure instructions that are on the fuel door label. There should be a recall and repair instructions to increase run flat tire pressure on Mercedes E class vehicles.
- Tires · Tires › Pressure monitoring and regulating systems
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if…
RE: Continental Pro Contact GX SSR MOE 245/40 R19 98 H M+S Original factory installed Mercedes E450 tires. I had 3 blowouts from hitting small potholes on 3 different tires in 1.5 years. These are complete immediate blowout going completely flat on impact. It could have very dangerous if I were driving a little faster and fortunately there was no other damage to the car or other persons. In each case, I hit a small pothole, and the tire blew out, flat to the ground. Because these are run flat tires, on the first 2 incidents I was able to drive home and to the dealer for tire repair/replacement. The third one was so bad that I could not drive all the way home and had to get towed. But all 3 incidents were scary and dangerous because of the sudden blowouts. The tires were not repairable and had to be replaced. I believe that the Mercedes Tire inflation instructions is unsafe and they should put more air in the tires to protect from the rim cutting into the tire when hitting a pothole. The driver's door "B" pilar placard says the "cold tire pressure: Front 41 psi Rear 47 psi". Mercedes repair shop inflates the tires according to the Fuel Filler Door decal that says " Front 36 psi, Rear 36 psi." That is a big difference in pressure -- as much as possible 11 psi under pressure. I believe these run flat tires failed because of too low of tire pressure when hitting the pothole. If the tires were inflated with the higher pressures as on the door pilar, the wheel rim would not have been able to cut into and through the tire wall because the higher tire pressure would prevent the impact of the rim cutting through the tire sidewall. I believe this a serious safety issue and Mercedes should be inflating this type run flat MOE tires to a much higher pressure and should not use the low-pressure instructions that are on the fuel door label. There should be a recall and repair instructions to increase run flat tire pressure on Mercedes E class vehicles.
- Tires
The contact owns a 2023 Mercedes-Benz E450 Convertible equipped with Continental Tires, Tire Line: ProContact GX SSR, Tire Size: 245/40/R19, DOT Number: 16YOF989F4623. The contact stated that while driving at an undisclosed speed over a bumpy road surface, the front driver's side tire experienced a…
The contact owns a 2023 Mercedes-Benz E450 Convertible equipped with Continental Tires, Tire Line: ProContact GX SSR, Tire Size: 245/40/R19, DOT Number: 16YOF989F4623. The contact stated that while driving at an undisclosed speed over a bumpy road surface, the front driver's side tire experienced a blowout several times, requiring the vehicle to be towed to the dealer, where the front driver's side tire was replaced four times by the dealer. Additionally, the contact stated that the failure recurred while driving, and a tire was replaced. The vehicle manufacturer was notified of the failure, but no assistance was provided. The tire manufacturer was not notified of the failure. The vehicle failure mileage was approximately 50. The tire failure mileage was approximately 50. The VIN was not available.
- Electrical system
I am submitting this complaint regarding serious and repeated electronic failures in my 2023 Mercedes-Benz E 450 that pose a significant safety risk to myself and other drivers on the road. The vehicle has experienced complete dashboard failures on multiple occasions, including the loss of…
I am submitting this complaint regarding serious and repeated electronic failures in my 2023 Mercedes-Benz E 450 that pose a significant safety risk to myself and other drivers on the road. The vehicle has experienced complete dashboard failures on multiple occasions, including the loss of speedometer, fuel gauge, and gear shift indicators. Most critically, the vehicle recently shut down while in motion, displaying a “malfunction” warning and disabling the electronic steering system. I was unable to maneuver the vehicle off the road, creating an extremely dangerous situation. This vehicle has been brought to the dealership three or more times for the same issue, with no permanent resolution. I believe this constitutes a serious safety defect. I respectfully request that the NHTSA investigate this matter as a potential recall issue.
- Back over prevention › Sensing system › Camera
My vehicle is equipped with a camera system which, when in reverse gear, displays objects/people behind the vehicle and, when going forward to park, displays objects/vehicles ahead. For the first 11 months of ownership, the system has worked properly. For the last 6 months the system has worked…
My vehicle is equipped with a camera system which, when in reverse gear, displays objects/people behind the vehicle and, when going forward to park, displays objects/vehicles ahead. For the first 11 months of ownership, the system has worked properly. For the last 6 months the system has worked intermittently. The vehicle, purchased new, is under warranty and has been returned to the dealership 4 times for software updates and and part replacements. Two weeks after the last visit, the camera system was inoperative again. Shortly after I returned home and went out again the camera system worked properly. Several years ago, Mercedes recalled 347,000 vehicles for a similar problem. My vehicle was purchased after the recall and did not fall into the category of vehicles that were recalled but it seems that, with the Mercedes brand, the problem still persists. To the extent the camera system will alert you to the presence of a person when backing up, this is a safety issue which needs to be addressed. Thank you
- Engine · Power train
While driving, malfunction warning flashed on dash, followed by 48v malfunction warning, then engine coolant overheat warning. The car then went into limp mode and finally stopped completely. Luckily this occurred on a residential street and not on a high speed freeway - the car gave very little…
While driving, malfunction warning flashed on dash, followed by 48v malfunction warning, then engine coolant overheat warning. The car then went into limp mode and finally stopped completely. Luckily this occurred on a residential street and not on a high speed freeway - the car gave very little warning before drastically reduced speed and shutting down systems. A 48 volt battery problem should have a redundant system to prevent the engine from overheating and not shutting down the vehicle at speed. Very dangerous!
- Fuel/propulsion system
The fuel pump on my vehicle failed multiple times, including coming off start / stop at traffic lights, as well as when being started. When at a stop light turning from red to green, my car did not respond, putting me in danger of being hit from behind. The vehicle is being repaired under warranty…
The fuel pump on my vehicle failed multiple times, including coming off start / stop at traffic lights, as well as when being started. When at a stop light turning from red to green, my car did not respond, putting me in danger of being hit from behind. The vehicle is being repaired under warranty at a manufacturer dealership. It appears this is a known issue under NHTSA recall 23V445000, although my vehicle is not currently included in the recall after a VIN search of the NHTSA check for recalls page. My vehicle exhibited the same signs as others affected by this recall, including flashing "malfunction" when it occurred.
- Engine
This has happened once before and I reported it then. This time I was stopped at a stop light and when I pressed the accelerator to go when the light turned green, the engine was off and would not go. The screen only said "malfunction" and no error codes (as before). I pressed the start button to…
This has happened once before and I reported it then. This time I was stopped at a stop light and when I pressed the accelerator to go when the light turned green, the engine was off and would not go. The screen only said "malfunction" and no error codes (as before). I pressed the start button to turn the car off and then restarted it. It was fine after that. I have left a message with my service agent at my Mercedes dealership. I had previously told them that this had happened before. I am concerned about the safety of a car the stalls like this. Please investigate. I see other reports about this from E class car owners on line in various forums.
- Engine · Fuel/propulsion system
I purchased an E450 Mercedes before reaching my first service appointment while driving my two daughters home from school the car began to shake uncontrollably, lost power, and then the engine light and oil lights came on. The car was towed to the manufacturer dealership for repair. It was…
I purchased an E450 Mercedes before reaching my first service appointment while driving my two daughters home from school the car began to shake uncontrollably, lost power, and then the engine light and oil lights came on. The car was towed to the manufacturer dealership for repair. It was determined that the piston number four was broken and the engine needed to be completely replaced. Less than two months after having the entire engine replaced the car broke down again with a similar shaking. This time one of my children and their friend were in the vehicle with me. The car was towed back to the dealership where they said the fuel pump went out and needed to be replaced. When I arrived to pick up the car, the technician pulling the car around noticed the shaking and the engine light on again. I did not leave in the car. The dealer kept the car to further investigate why the engine light was on again. Two days later they called to say they’d been driving the car around to “air it out” as air must have been trapped in the fuel system and that nothing further needed to be done. I am not confident that this vehicle is safe to drive or properly repaired. I’m also not confident that this vehicle doesn’t have other unknown issues that will arise overtime. It’s unsafe to drive children in this car. I still have not even reached 10,000 miles on this car.
- Fuel system, gasoline
The contact owns a 2023 Mercedes-Benz E450. The contact received notification of NHTSA Campaign Number: 23V880000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall…
The contact owns a 2023 Mercedes-Benz E450. The contact received notification of NHTSA Campaign Number: 23V880000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. While the contact’s wife was driving and then stopped at a traffic light, the vehicle independently turned off. The contact stated that several unknown warning lights were illuminated. In addition, the contact stated that the failure caused a traffic back up on a busy roadway. The contact stated that after several attempts, the vehicle restarted. The vehicle was driven to the residence. The contact informed the dealer by phone of the failure and that the parts were not available. The dealer was made aware of the failure but confirmed that parts were not yet available. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 600.
- Electrical system · Engine · Power train
My 2023 Mercedes 450E car was purchased on June 11, 2023 and has 1,750 miles. On 2 to 3 different occasions, I was stopped at a light waiting to make a left turn, fortunately my light was red and not a green permitting turning, which would have meant I would have pulled up and into the cross…
My 2023 Mercedes 450E car was purchased on June 11, 2023 and has 1,750 miles. On 2 to 3 different occasions, I was stopped at a light waiting to make a left turn, fortunately my light was red and not a green permitting turning, which would have meant I would have pulled up and into the cross section to prepare to turn; I pushed the gas in the drive position and large red malfunction letters displayed across the dashboard and the car just revved. I put it in park and then drive postion a few times and had the same result. Finally, I turned the car off and back on, put it in drive, pushed the gas and it went. I live in Miami, with the serious traffic congestion. The issues that my stalled car caused blocking other drivers’ passage through a few lights, can only be imagined Fortunately, no accidents happened as other drivers attempted to get around my vehicle. The car was taken into service on October 9, 2023, many tests were performed, a diagnosis of the stalling problem was provided, however, I was told there no solution to the problem at this time, “maybe in the future” I was told. Turn off the Economy button, I was told. What if I forget? What if someone else is driving the car? As one can clearly read from the service record, attached hereto, the car is irreparable.The car was released to me anyway on October 28, 2023. After complaining to Mercedes corporate, they offered to repurchase my car. I said I wanted a replacement. They said my model had this problem and a replacement would not solve my problem. I asked about the safety of all other owners and drivers coming into contact with this model on the road and why a recall hadn't been issued and there was no response, nor concern from Mercedes. This model can stall in stop and go traffic on the nation's interstate highways and there will be fatalities. Mercedes, fix the car and give notice to owners of this model about the defect.
- Power train
My first incident was on July 17, 2023, the transmission shifted from drive to neutral, with out me touching the gear shift lever in any way. My safety and any passengers I have in this car, could be at risk, at this point I was going about 40 MPH, going into a gradual curve, entering a Entrance…
My first incident was on July 17, 2023, the transmission shifted from drive to neutral, with out me touching the gear shift lever in any way. My safety and any passengers I have in this car, could be at risk, at this point I was going about 40 MPH, going into a gradual curve, entering a Entrance to 95 north, I had slowed down to the entrance ramp speed, this is when the transmission went from Drive to Neutral, with out me touching the gear shift lever. I had a appointment at Quirk Auto Park, there service dept. in Bangor, Maine, no warning lamps came on the dashboard, they proceeded to put the diagnostic tool on the car, they came out maybe 15or20 minutes later, they didn’t find anything. The first incident I also reported to the NHTSA. The second incident took place on 10/20/23, I was going under 25 MPH, I was into a left hand turn, the transmission came out of drive, and went into neutral, I did not touch the gear shift lever at all. There was no warning lamps that came on after this second incident either.
- Engine
I had just left home and was about two blocks from my house when the engine stopped running and the word “malfunction” appeared on the display. It would not restart until I hit the off button and then I restarted it. Definite safety issue if I had been on the freeway or a busy street.
- Power train
The contact owns a 2023 Mercedes-Benz E450. The contact stated that while driving at an undisclosed speed and merging into traffic, the gear shifter inadvertently shifted into neutral (N). There was no warning light illuminated. The contact stated that the RPM was fluctuating. The vehicle was taken…
The contact owns a 2023 Mercedes-Benz E450. The contact stated that while driving at an undisclosed speed and merging into traffic, the gear shifter inadvertently shifted into neutral (N). There was no warning light illuminated. The contact stated that the RPM was fluctuating. The vehicle was taken to the dealer to be diagnosed; however, the mechanic was unable to duplicate the failure. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 300.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010744Complaint Engine cooling fan running for an extended time after switching off vehicle. Cause Optimized thermal management in latest PTCU software. Remedy This is a normal function in the latest PTCU software. Engine fan will operate for up to 20 minutes after ignition is switched off. Note: Repair work should only be performed if a clear malfunction is identified
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009025Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008072Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
- 11008058Complaint Engine does not restart from ECO start. Hybrid system malfunction (Gears symbol) in instrument cluster. Fault codes below may be stored in ISA control unit. P0A44B2- Drive motor "A" Position Sensor Circuit Overspeed. The speed is below the threshold value. P0AFB00- The power supply of high voltage on-board electrical system is too high. Cause Reduced current output to ISA during ECO start. Remedy If additional faults are stored for 48V system components, process these first. Update software of ISA control unit. New software numbers - A2569022304 A2569033903
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007964Complaint Surface-flush door handle fails to retract and/or extend Cause Under analysis Remedy Create a TIPS case and send to the Body/Chassis/Entertainment inbox. Please determine the following information: 1. Which complaint did the customer come into the workshop with? 2. Are fault codes stored in the control units A17/x? Please attach quick test to the TIPS case. Please also take pictures of the door handle from a distance of approx. 2 m (from outside), as well as a detailed picture with high resolution from close up. Then remove door handle and bearing bracket and check for any mechanical damage, if necessary take photos of damage. Keep damaged part for further analysis.
- 11007956Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2023 CLS (257 platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003212Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. 3. NOTE: Coding Parameter 'Shimmy' should be turned off and the actual value should read "Shimmy aus". With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11003205Complaint The driver's seat memory settings do not synchronize with the driver's user profile as described in the operator's manual. Driver's seat settings are not transferred to the vehicle. Cause The driver's seat does not support the profile synchronization feature on these vehicles. Remedy There is no remedy for this complaint. The vehicle is working as designed. Note: Do not replace any parts.
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 11000519Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023-2024 C-Class, CLE, E-Class, EQE, EQS, GLC, GLE, GLS, GT, S-Class, and SL vehicles (205, 206, 236, 213, 214, 238, 294, 295, 296, 297, 253, 167, 290, 223, 232 platform), the tire sealant bottle may not meet specifications. The possibility exists that the tire sealant bottle may leak within the installation location. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244735Wheezing noises from the front shock absorbers when passing over surface undulations and rough road. The noises may become more conspicuous with warm damper oil. The flow noises of the damper oil are currently being analyzed. The wheezing noises are currently considered standard for the series. Replacing the shock absorbers will yield no benefit and will not remedy the problem. Please report complaints regarding these wheezing noises via TIPS.
- 10243346Rear side window reversed when opening/closing soft top - Convenience closing 1. Rear side window setting 2. Damage to inner rear side window sealing rail (abrasion marks at sealing rail, see picture, folding of the sealing lip, 3. Window panel gap sidewall width too low. To this end, check the width of the side wall for dimensional accuracy; Note: Inner and outer sealing rail are removed 4. Window divider at rear side window, metal insert sticks out 1. Adjust the rear side window according to the specifications in the WIS. Note: Rear side window/center setting to center of window panel gap sidewall 2. Check inner sealing rail for damage. Replace in the event of damage 3. Enlarge width of side wall of window panel gap; see picture 4. Information: Measuring point 1 at 0 cm: Nominal dimension 37.7 mm Measuring point 2 at 22 cm: Nominal dimension 31.0 mm Measuring point 3 at 34 cm: Nominal dimension 33.5 mm 4. If side window continues to be inoperable -- open TIPS case
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
Every Mercedes-Benz E 450 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.