2023 Mercedes-Benz EQE 500

Recalls

2 recalls name the 2023 Mercedes-Benz EQE 500. Newest first.

• Electrical system › Wiring › Fuses and circuit breakers

  Feb 16, 2024NHTSA 24V11500031,848 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 C300, AMG C43, S580e, S580, Maybach S580, Maybach S680, AMG SL43, AMGSL63, GLC300, EQE350, EQE500, EQS450, EQS580, AMG EQS, 2023 S500, AMG SL55, AMG EQE, 2024 E350, E450, AMG C63e S, CLE300 Coupe, CLE450 Coupe, and GLC300 Coupe vehicles. The 80-Amp fuses may have been manufactured incorrectly…

  Risk and remedy

  Risk

  An 80-Amp fuse that fails can result in a sudden loss of drive power or a loss of critical safety functions such as the restraint systems or instrument cluster, increasing the risk of a crash or injury. Additionally, there could be an increased risk of a fire.

  Remedy

  Dealers will replace the main fuse boxes, free of charge. Owner notification letters were mailed April 5, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024030008.

  Full recall details →

• Structure › Frame and members

  Aug 4, 2023NHTSA 23V55500010 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023 AMG EQE, EQE 500, and EQE 350 vehicles. The absorbers in the roof frame may not be secured properly and can detach during window air bag deployment.

  Risk and remedy

  Risk

  In the event of a crash with window air bag deployment, detached absorbers can strike vehicle occupants and increase their risk of injury.

  Remedy

  Dealers will replace the absorbers, free of charge. Owner notification letters were mailed September 1, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023080004.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system3
2. Service brakes2
3. Unknown or other2
4. Air bags1
5. Tires1
6. Power train1
7. Engine1
8. Forward collision avoidance1

Latest complaints

• Jul 6, 2025PACrash
  Service brakes
  I was in bumper-to-bumper traffic traveling West on Interstate 376 in Pittsburgh, PA. The weather was clear and cool, and the pavement where I was driving was dry. I was proceeding through the Fort Pitt tunnel outbound. Given that traffic was stop and go and moving very slowly, I switched my…

  I was in bumper-to-bumper traffic traveling West on Interstate 376 in Pittsburgh, PA. The weather was clear and cool, and the pavement where I was driving was dry. I was proceeding through the Fort Pitt tunnel outbound. Given that traffic was stop and go and moving very slowly, I switched my recouperation setting from “normal” to “strong” to enable one-pedal driving using the paddles on the sides of the steering wheel. Immediately after doing so, traffic was inching forward just West of the Fort Pitt tunnel, starting up Greentree Hill. I saw the truck in front of me starting to move forward so I took my foot off my brake (up to that point it had functioned correctly) and the car started moving forward slowly. When the brake lights of the truck in front of me illuminated, I placed my foot on my brake. The brake pedal depressed but the car brakes did not function. I immediately noted that the brakes had not functioned and as a result I pressed harder with my foot on the brake pedal. Nothing happened–the brakes did not function. I then used both feet and pressed as hard as I could against the brake pedal. Again, nothing happened–the brakes did not function. I continued to press as hard as I could with two feet as the car proceeded forward into the back bumper of the truck in front of me. The collision occurred at approximately two miles per hour and the damage to my car was mainly caused by the rear hitch on the truck, which went into my front bumper. Mercedes-Benz USA has inspected the car and stated it did not malfunction, but they did not perform any tests in a manner to recreate the settings of the car that were in place at the time of the incident. The car is currently in their control and that of my dealer. No warning lamps or other symptoms of the problem appeared prior to or during this incident.

• Jun 12, 2025MO5,000 mi
  Tires
  The contact owns a 2023 Mercedes- Benz EQE 500 equipped with Pirelli Tires, Tire Line: P-Zero All Season, Tire Size: 255/40/R20, and DOT Number: 1931H811J. The contact stated while driving at an undisclosed speed over a bump, the tires had either experienced a blow out or blisters. The contact…

  The contact owns a 2023 Mercedes- Benz EQE 500 equipped with Pirelli Tires, Tire Line: P-Zero All Season, Tire Size: 255/40/R20, and DOT Number: 1931H811J. The contact stated while driving at an undisclosed speed over a bump, the tires had either experienced a blow out or blisters. The contact stated that the failure had occurred on all four original tires and had recurred on several of the same replacement tires. The cause of the failures were not determined. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The vehicle failure mileage was approximately 5,000. The tires failure mileage was approximately 5,000.

• Sep 24, 2024MD
  Electrical system · Engine · Power train
  At 0820 AM on Monday, 23 SEP 24 while traveling South on interstate 95/495 in rush hour traffic the vehicle lost complete power and 3-4 messages appeared in the display. I recall one saying the rear differential is inoperable. I turned on the emergency flashers and was fortunate to allow the car to…

  At 0820 AM on Monday, 23 SEP 24 while traveling South on interstate 95/495 in rush hour traffic the vehicle lost complete power and 3-4 messages appeared in the display. I recall one saying the rear differential is inoperable. I turned on the emergency flashers and was fortunate to allow the car to coast to the highway’s left shoulder without causing an accident. I don’t remember the other warnings as I was preoccupied trying to get the car safely off the highway. I was able to restart the vehicle after allowing it to sit for a minute or two. I have an appointment to have it inspected on Thursday at Mercedes of Annapolis, MD. This is the second time the vehicle has lost power while traveling on the beltway. A recall was eventually issued a few weeks after the first incident. I convinced my wife to purchase this vehicle to replace her 20 year old car thinking it would provide safe, reliable transportation. To the contrary the car has had to be towed twice, has lost power on the highway and was in the shop almost a month for a noise complaint. I was told the noise issue was due to 3 bad tires, likely due to potholes, and charged $1741 to replace them. I am totally convinced the issue was not related to potholes but had no recourse other than to pay the $1741. My wife feels totally unsafe driving the car, particularly when I am out of town for work.

• Jun 5, 2024NJ2,500 mi
  Electrical system
  The contact owns a 2023 Mercedes-Benz EQE500. The contact stated that while driving approximately 45 MPH, the vehicle lost propulsion and stalled. Moments later, the contact was able to restart the vehicle and continued driving. The next day the vehicle was driven to the local dealer who determined…

  The contact owns a 2023 Mercedes-Benz EQE500. The contact stated that while driving approximately 45 MPH, the vehicle lost propulsion and stalled. Moments later, the contact was able to restart the vehicle and continued driving. The next day the vehicle was driven to the local dealer who determined that the failure was related to NHTSA Campaign Number: 24V372000 (Electrical System); but the part to do the recall repair was not yet available. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 2,500.

• Apr 21, 2024CA
  Forward collision avoidance › Automatic emergency braking
  There have been 3 instances of the same incident of the Automatic Emergency Breaking system failing, the 3 times has happened over the 8 months I have owned the car. Mercedes has aknowledged the failure of the automatic breaking system but they do not have any fixes for it. When I am driving, if…

  There have been 3 instances of the same incident of the Automatic Emergency Breaking system failing, the 3 times has happened over the 8 months I have owned the car. Mercedes has aknowledged the failure of the automatic breaking system but they do not have any fixes for it. When I am driving, if the safety system senses a police radar system a car may have installed (like an old school one on a civilian's car dashboard) the car's security system "shuts down" for a couple seconds and slams on the breaks nearly causing a crash. I have been driving at 15-20 MPH on a clear street and out of nowhere the car slams on the breaks because it detects someone's radar detector. As you can imagine, this is absolutley terrifying to be driving on a clear street and have the car slam on it's breaks. My heart rate goes up, I have been visibly shaken up. The feeling is as if I got into a car accident-but I didn't it was self-induced by the vehicle. I am worried if someone is driving behind me and is not prepared for the car to break, I will be rear-ended. Please help Mercedes owners fix this, it's horrible.

• Mar 24, 2024NVCrash1 injury
  Air bags · Service brakes · Unknown or other
  On [XXX] my wife was driving to a place of business here in Las Vegas, NV at approximately [XXX]. She proceeded to pull into a parking spot with her foot on the brake pulling up to the parking block. She never took her foot off the brake preparing to stop once she reached the parking block. Once…

  On [XXX] my wife was driving to a place of business here in Las Vegas, NV at approximately [XXX]. She proceeded to pull into a parking spot with her foot on the brake pulling up to the parking block. She never took her foot off the brake preparing to stop once she reached the parking block. Once she reached the parking block she applied the brakes firmly to bring the car to a stop, however, the car took off at a high rate of speed. The car then jumped over the parking block onto the sidewalk my wife continued to apply the brakes but they did not work the car tires kept spinning and eventually caused her to hit the wall of the building. At the time of the incident no warning lights came on the dash because everything went blank, no airbag deployed, no messages came on the car nor did it send any messages to me alerting me that my vehicle was involved in a accident. Due to this vehicle malfunctioning my wife has suffered a concussion, bruises to her breast and chest area and she also has a strain to her hips due to the seat belt malfunction. The seatbelt did not work properly it did not keep her restrained to the seat as designed. The building was of course damaged as a result of this vehicle malfunction. My wife unfortunately has suffered mental and bodily issues she has been traumatized due to this vehicle malfunction she has voiced over and over how this experience has affected her she also has repeatedly stated how this event took place and how it now makes her not ever want to ride in this car or any other electric car ever again. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Feb 6, 2024FL
  Unknown or other
  On 01/12/2024 the driver profile on my vehicle was remotely wiped with no authorization. This profile has settings for multiple automated driver functions including a creep function that I have always left off (On is the default). Once the driver profile was wiped, when I lifted my foot off the…

  On 01/12/2024 the driver profile on my vehicle was remotely wiped with no authorization. This profile has settings for multiple automated driver functions including a creep function that I have always left off (On is the default). Once the driver profile was wiped, when I lifted my foot off the accelerator expecting the vehicle to come to a stop it did not. It continued traveling forward without any accelerator input.

• Aug 6, 2023WA
  Electrical system

  Electrical interference with USB audio. There are loose connections that travel on the headliner all the way to the back of the car rear top speakers. Audio source suddenly gets disconnected and make a huge buzzing sound on the rear left speaker mounted to headliner. A potential fire hazard.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010648Complaint Transfer of selected user-defined scene/ animation (Mercedes-Benz Phone App) from HU to ECU software fails to start. Charging bar stops at 0%. (Picture in attachment) Cause Communication between headlight control unit and HU. Remedy Update the software of the following control units to the latest version: - A26/17 - MBUX multimedia system (head unit) - E1n14 - Front left digital headlight control unit (DHLS-CU-VL) - E2n14 - Front right digital headlight control unit (DHLS-CU-VR)
• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11009204Complaint The flush-mounted door handle could jam when it is pulled out and may move in a jerky manner when doing so. In the area of the paneling section of the door, paint damage could be present (picture 1) and/or an abrasion point could be present at the door handle (picture 2). Cause The door handle could be installed too low in the y direction and/or the z direction (picture 3); as a result, the door handle could brush the door at the paneling section of the door. Remedy 1.) Loosen screws from bearing bracket (picture 4, step 1). 2.) Remove bearing bracket (see picture 4, step 2) from door. The door handle must be in pulled-in position. Open the affected door and push the door lock's rotary tumbler into the main catch. Lock the vehicle using the transmitter key so that the door handle is pulled in. Detach plug connector from bearing bracket (center slot). 3.) Paint over paint damage at door paneling (see picture 1) according to manufacturer specifications, using spot repair procedure if necessary. 4.) Loosen old assembly frame (picture 5, step 3). The assembly frame is bonded. Remove adhesive residue at front door. Bonding surfaces must be free of dust, oil, grease, wax, dirt residues and other adhesive components. Otherwise, this can lead to bonding problems. See "Parts" for part number of cleaning agent. 5.) Position new assembly frame (picture 5, step 3) at door. Remove protective film of tape at assembly frame beforehand. The assembly frame (picture 5, step 3) must have the same clearance all around the flange. 6.) Replace door handle, if an abrasion point (picture 2) is present. 7.) Screw in WITOL fasteners (picture 6) completely at mounting points of bearing bracket (picture 7, step 1) and align screws so that they are flush (picture 7, step 2). 8.) Position bearing bracket (picture 4, step 2). The door handle must have the same clearance all around in relation to the paneling section of the door (picture 8). 9.) Press the bearing bracket firmly against the paneling of the door and tighten the screws (picture 4, step 1) (=> torque: 6 Nm). 10.) Check the positioning of the bearing bracket. If necessary, loosen the screws slightly, readjust the bearing bracket slightly, then retighten the screws (=> torque: 6 Nm).
• 11009138Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause Older software release, HLI control units Remedy Update of HLI control units (E1n9 / E2n9)
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
• 11008883Complaint Play/noise at height adjuster or in seat guide rail on front seats Cause Tolerances and variations in the manufacturing process Remedy Review of barcode adhesive label on air intake pipe of height adjuster. The seat frame base with the height adjuster motor can be replaced if the production status is lower than E105 (pic.1: seat label) If the production status is higher than or equal to E105, please create a TIPS case with videos and photos and send to B/C/E inbox. In isolated cases, the label may be located on the inside of the air intake pipe; for this, the seat cushion must be removed.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008875Complaint Sliding sunroof panel of panoramic sliding sunroof reversed (temporarily, once, multiple times) during closing process without entrapment event. Cause It is not possible to save the relearning process for force progression after each actuation. A, e.g. mechanical sluggishness caused by aging cannot be compensated for here. Remedy Perform commissioning of panoramic roof control unit (PSD, A98, TSSR223). Reference to escalation closing during reversing processes (also described in Operators Manual), if vehicle in customer possession (see Video_1): If the panoramic roof blocks up when closing and then opens again slightly (reversing process): Immediately after automatic reversing, wipe forwards on the control panel of the overhead control panel and hold until the panoramic roof is closed. The panoramic roof is closed with greater closing force. If the panoramic roof blocks up again and then opens again slightly (reversing process): repeat previous step. The panoramic roof is closed again with greater closing force.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008062Complaint The electric range does not meet customer's expectations. Cause The following information is being provided for educational purposes only: At Mercedes-Benz, we believe that our vehicles should display to the driver a range that in all probability can actually be achieved. These ranges are predictions - the range actually achieved may therefore differ from the range shown. The calculation for the predicted range takes into account the current outside temperature, the set temperature of the air conditioning system, the battery capacity and the characteristics of previous journeys (sporty/anticipatory driving style). Where previous journeys are concerned, factors given particular consideration are individual driving style and the use of other power consumers (seat heating, lights, charging function for smartphones, etc.). It is therefore possible that data from the last few hundred kilometers driven is also used in the calculation. Consequently any change in usage behavior will only slowly affect the predicted range. If active navigation or active commuter route is used, additional information about the route ahead (for example elevation profile, traffic volume) can be included in the range calculation. Remedy The customer's individual input to the range can be reset. Depending on the vehicle, the reset can be done in the instrument cluster or the head unit. For plug-in hybrid vehicles of model series 166 (all), 205 (up to modification year 18/1), 213 (up to modification year 17/2), 222 (up to modification year 17/2), 253 (up to modification year 19/1), the range can be reset by resetting the trip computer ("From reset", "From start" and "Day cycle counter"). After the reset, a value based on the certified range will be shown. For electric and plug-in hybrid vehicles of model series 205 (from modification year 18/2), 213 (from modification year 18/1), 222 (from modification year 18/1), 253 (from modification year 19/2) and model series 118, 167, 177, 206, 223, 247, 293, 295, 297 a reset is only possible by resetting the head unit to the factory settings. This will delete all saved customer data and any settings made (e.g. radio settings, navigation destinations). If necessary, therefore, back up the customer data onto a USB flash drive using the Backup function before performing a reset. As from vehicles with NTG 7, Mercedes me is used for the making the backup. After the reset, an empirical value is displayed that is based on normal use of the vehicle and the current climatic conditions (set temperature and outside temperature - commensurately higher values will be achieved if the air conditioning system is switched off). Depending on driving style, outside temperature and which power consumers are actually switched on, the achieved range may significantly exceed this range, but likewise may also fall significantly short of it. Further information on battery capacity and aging can be found in document SI47.70-P-0070A.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007966Complaint Display dark (total or partial) of one or more ASCM (AMG) steering wheel button displays - see attachment. Note: There is no loss of vehicle functionality due to this complaint. Cause Software can cause a partial display on the ASCM. Remedy Please perform the following steps in the event of a total or partial display of the ASCM displays: 1. Perform a hard reset (disconnect power supply) of control unit A74/2 (ASCM) for 2 minutes. 2. Perform a software update of the A74/2 (ASCM), N145 (DRVU) and A26/17 (HU). 3. Reset the user profile via the head unit settings menu. (Full factory reset)
• 11007964Complaint Surface-flush door handle fails to retract and/or extend Cause Under analysis Remedy Create a TIPS case and send to the Body/Chassis/Entertainment inbox. Please determine the following information: 1. Which complaint did the customer come into the workshop with? 2. Are fault codes stored in the control units A17/x? Please attach quick test to the TIPS case. Please also take pictures of the door handle from a distance of approx. 2 m (from outside), as well as a detailed picture with high resolution from close up. Then remove door handle and bearing bracket and check for any mechanical damage, if necessary take photos of damage. Keep damaged part for further analysis.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11007752Complaint Transfer of selected user-defined scene/ animation (MeApp) from HU to ECU software fails to start. Charging bar stops at 0%. (Picture in attachment) Cause Communication between light control unit and HU Remedy Software update to latest version: - A26/17 - MBUX multimedia system (head unit) - E1n14 - Front left digital headlamp control unit (DHLS-CU-VL) - E2n14 - Front right digital headlamp control unit (DHLS-CU-VR)
• 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
• 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
• 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
• 11006699Complaint Radio reception interference and the following DTCs are displayed in the A26/17 - MBUX multimedia system control unit as "active and stored": B19B313 - Antenna 1 open load B19B413 - Antenna 2 open load B19B513 - Antenna 3 open load B19B613 - Antenna 4 open load Cause Antenna amplifier Remedy Replace the antenna amplifier.
• 11006688Complaint Red warning message in instrument cluster: "Towing not allowed, see Operator's Manual, consult workshop without starting the engine again". Cause Missing diaphragm on high voltage PTC (interior heating) N33/14 component part results in moisture buildup in the installation space for the heater and causes an insulation fault. The entry of moisture into the high voltage PTC (interior heating) N33/14 in the high voltage wiring harness to the DC/DC converter N83/1 causes a slow-acting insulation fault. This may occur sporadically only to start with before actively developing over time. Remedy Exchange high voltage PTC (interior heating) N33/14 with new part with diaphragm (production date as from 22T231, see component part label). If necessary, and after further testing/measurement, replace wiring harness for DC/DC converter N83/1 to high voltage PTC (interior heating) N33/14. Note: According to the Replacement Parts Department only high voltage PTCs (interior heating) with a diaphragm and with production date as from 22T231 are available!
• 11006686Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that certain MY 2023-2024 EQE Sedan, EQS Sedan, and EQS SUV (295, 296, and 297 platform) vehicles may not start. In this case, the fault message Cannot Start Vehicle See Operator's Manual may appear in the instrument cluster. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the battery management system control unit software.
• 11005350Complaint Child seat detected message is shown in the central display and no child seat is installed on the front passenger seat at the time the display message is shown. Cause In certain circumstances, the gesture recognition system may interpret the occupancy status as a child seat present. The following possible conditions may lead to this: 1. Front passenger seat occupied by passenger 2. Object on front passenger seat, e.g. bag or backpack 3. Front passenger seat not occupied The gesture recognition system uses optical imaging to assess the front passenger seat and whether it is occupied and is independent from the occupant classification system input used for airbag deployment. The gesture recognition assessment has no connection to the airbag system. As this is an optical measurement, in certain circumstances a child seat message may be displayed based on the results of the interpretation. There is no influence on airbag system. There is no connection to airbag system. Remedy Software update of control unit N168 - Gesture recognition system OMSH223
• 11005337Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B129C00 - Malfunction in control unit for telematics services" is active and stored - The head unit shows no internet connection Cause Under analysis. Remedy Please create a TIPS case, attach a RAMSES control unit log to the case.
• 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11005265The vehicles were visible and flagged in VMI as OPEN on March 15, 2024. Unrepaired affected vehicles will be removed from VMI on July 15, 2024.
• 11003213Complaint USB port data storage medium is not recognized, but charging function is still available. We are only aware of this complaint in a few isolated cases and it only occurs intermittently (not in every driving cycle). Cause Multimedia connection unit Remedy Replace the multimedia connection unit. Affected item numbers: A 214 820 81 00 A 223 820 14 05 Manufactured before 10/2023 modified parts have been manufactured since 10/2023.
• 11003090Service Campaign 2024010013: The powertrain control unit software may not meet current production specifications where the authentication for charging via plug and charge may not function as intended. An authorized Mercedes-Benz dealer will update the powertrain control unit SCN coding.
• 11000740An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk of your vehicle, free of charge. The bottle may potentially leak and may not be available for use in case of a flat tire. Your vehicle must be brought to a dealer to complete this campaign. Please schedule an appointment by contacting our Customer Assistance Center at 1-800-367-6372, or locate your nearest dealer using the QR code and Find a Dealer section.
• 11000541Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11000534Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 22-24 C-Class, EQE, EQS, GLC, S-Class, SL (206, 294, 295, 296, 297, 254, 223, 232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11000531Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY23-24 CLE, E-Class, EQE, EQS, and S-Class vehicles (236, 214, 294, 295, 296, 297, 223 platform), the communication module SCN coding does not correspond with the latest series production configuration. The communication module will receive an OTA update that updates the SCN coding to the latest series production configuration. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 11000519Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2023-2024 C-Class, CLE, E-Class, EQE, EQS, GLC, GLE, GLS, GT, S-Class, and SL vehicles (205, 206, 236, 213, 214, 238, 294, 295, 296, 297, 253, 167, 290, 223, 232 platform), the tire sealant bottle may not meet specifications. The possibility exists that the tire sealant bottle may leak within the installation location. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the TIREFIT bottle in the trunk.
• 10253716Complaint Wheel trim element grazes against fixed caliper Cause Tolerance between wheel trim element and fixed caliper Remedy Rework wheel trim element as described in the instructions with a suitable tool 2-3 mm.
• 10253714The update of the RAMSES 1.1 module to the SW version E139.4 results in a fault in the vtime of the module and therefore to the following possible connection problems: Remote status: The time stamp of the last update that is displayed on the side of the sheet with the vehicle status contains the wrong information. Geofence: Geofence notifications are not sent if vtime is invalid. Programming of charging settings: The update timestamp on the side of the sheet with the loading settings features an incorrect timestamp. The timestamp for the end of the charging process would contain the wrong information. The status and end of the charging process are not displayed. The function itself is not affected; only the timestamps are incorrect. Pre-entry climate control: The time stamp of the last update that is displayed on the side of the sheet with the vehicle status contains the wrong information. The next departure time would be affected. The function itself is not affected; only the timestamps are incorrect. NOTE: The functionality of the eCall system is not affected. RAMSES 1.1 software E139.4. Perform a SW update of the RAMSES 1.1 module to the latest E139.5 software.
• 10253712The display in the Lower Multifunction Steering Wheel Button Group (A74/2) may be completely or partially inoperable (see attached picture). Note: There is no loss of vehicle functionality due to this complaint The complaint may occur when a new user profile is created in MBUX. The cause of the problem may be a fault in the DRVU software (N145/1). Please update the software in the AMG drive unit (N145) to the following level or newer. Software A0019024902. If a fault profile still occurs in the ASCM (A74/2) even with the correctly installed software (N145), please create a TIPS case and reference this LI.
• 10253696This is to notify you of the Service Campaign OTA software update of the AMG Chassis Controller (ACC) in 1,349 Model Year (MY) 22-24 EQE, EQS (295, 297 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY22-24 EQE, EQS vehicles (295, 297 platform), the AMG Chassis Controller (ACC) software does not correspond with the latest series production configuration. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.

Every Mercedes-Benz EQE 500 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.