2020 Mercedes-Benz Glb 200

Owner complaints

What owners report most

1. Air bags1
2. Electronic stability control (esc)1
3. Structure1

Latest complaints

• Mar 17, 2020CA
  Air bags · Electronic stability control (esc) · Structure › Body
  Dealership first quoted us a lower price then at the time of selling charged us more I have the proves ,then showed us this particular vehicle which they sold us with a spare tyre but took out when they handed the key,, which we realized when we were driving on the road. 2ND the trunk where the…

  Dealership first quoted us a lower price then at the time of selling charged us more I have the proves ,then showed us this particular vehicle which they sold us with a spare tyre but took out when they handed the key,, which we realized when we were driving on the road. 2ND the trunk where the tyre was kept was handed over broken.3.first week the car had air bag warning on 4.THE sun roof was trembling and shaking making noises in the first week 5.THE trunk automatic foot opener never worked since first week .in the first week the warning for servicing also came up,so practically we have been taking this brand new vehicle to the repair service center every week ,kindly see the log book ,feel totally unsafe driving this car mercedes AMG glb 2020 bbought from beverly hills dealership,, la. We have all the proves pictures when required.thx

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008878Complaint Customer complains of wind noises. Cause The cause is being clarified. Remedy If wind noises can be clearly attributed to the roof railing, create a TIPS case with the following information: Detailed pictures of the roof railing in the actual state Detailed pictures of the roof railing in the taped-up state List of the work to pinpoint the cause Result of test to see whether the component part moves -> establish there is no rattle
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11003208Complaint Noise can be heard coming from the air conditioning system at higher blower motor speeds. Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Instructions for the installation of Retrofit Kit TOP598-MFA2 Bermuda foam for model series X243/X247 A2478351400 Sealing frame A2478351500 Sealing frame A2478351600 Sealing frame A2478351700 Sealing frame A2478351800 Sealing frame A2478351900 Sealing frame A2478300104 Housing cover A2478320200 Drainage fitting Steps: 1- Remove windshield wiper as per work instructions: AR82.30-P-6100MFA 2- Remove water baffle cover as per work instructions:AR83.10-P-1411MFB 3- Thoroughly clean body/body-in-white at marked positions and remove plastic cover to air inlet. Then extract air filter. 4- Attach body-in-white foam A2478351600 to cutout at body-in-white. If necessary, fix part in place with light pressure. 5- Attach foam mat A2478351400 to previously cleaned part of body-in-white. Ensure that hole of foam mat is over the hole in the body-in-white. 6- Attach sealing frame A2478351800 along edge as shown in picture. Ensure that the plastic strip is inserted flush with the offset in the previously attached foam mat. 7- Attach sealing frame A2478351700 as shown in the picture. Take care here as the strip should be attached flush to the foam strip positioned lengthwise and must run vertically on the body-in-white downward in the direction of the seam. 8- Attach sealing frame A2478351900 as shown in the picture. Ensure that the foam strip must run along the seam and must be curved outward along the running direction at the end. (As a guide, the curvature should run so that there is a space of approx. 1 cm between the foam strip and the threaded hole). Alternatively, if the corresponding foam in the right picture is present, place the sealing frame A2478351900 along the foam as shown in the picture. 9- Insert drainage fitting A2478320200. When doing so, ensure that the foam flap is aligned in the direction of the fender as shown in the picture and does not fold upward during insertion. Insert fitting with light pressure until it audibly engages. 10- Attach sealing frame A2478351500 to water baffle as in the picture and insert inlet sieve A2478300104 (see picture). 11- Insert water baffle. When doing so, ensure that sealing frame A2478351600 does not fall out of position. Also ensure that the foam frames A2478351700, A2478351800 and A2478351900 run between the body-in-white and the water baffle (see picture). 12 - Clean out the water drains of any debris and ensure proper water flow away from the blower area. 13- Reinstallation of water baffle and windshield wiper (see step 1).
• 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
• 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
• 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
• 10249731Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2021 GLA and GLB (247 platform) vehicles, the identification plate on the B-pillar does not correspond to current specifications.MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the identification plate on the B-pillar.
• 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
• 10249537Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
• 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
• 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
• 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
• 10241534In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first). This extended warranty applies to the condition described below that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinder head). The valve guide and/or seat ring may wear over time due to increased lateral forces during operation. This could potentially cause combustion misfire for cylinder 1 through 4, resulting in an activation of the check engine Malfunction Indicator Lamp (MIL). Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information, and may be audited. P030085 Combustion misfire has been detected P030x85 Cylinder x misfire detected. (x = the affected cylinder) P1CEF85 - Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at atleast one cylinder. P1CE577 - Injector injection quantity adjustment for uniform mixture formation has detected an excessively lean mixture at atleast one cylinder. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 01201 Cylinder Head 05202 Exhaust Valve 01205 Valve seat ring exhaust valve 01206 Valve Guide Exhaust Valve
• 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
• 10238424In the MBUX weather app, the temperature is displayed in the wrong unit (Fahrenheit instead of C, or vice versa). Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)
• 10235667Complaint Ambient lighting malfunctions sporadically, mainly in the Ocean Blue color value and with animation "ON". After the next ignition cycle, the ambient lighting functions again correctly. Cause Software in coupling elements (EKE) faulty. The coupling element software cannot be updated in After-Sales. Remedy In a complaint case, replace the respective wiring harness (coupling elements are installed on the wiring harness) for ambient lighting.
• 10233789Complaint Excessive resistance of door side windows when being raised/lowered, cracking and squeaking noises. Cause Sealing lip of inner sealing rail (see picture 1 and picture 2, pos. 40 and 130) folds down while side windows are being lowered (opened). When the side windows are raised (closed), the sealing lip is pulled back up again. Remedy Replace inner sealing rail. Then perform normalization of the window lifter system in the relevant door control unit.
• 10233782Complaint Squeaking noises from the front axle brakes when operating the brakes. The noise occurs regardless of the temperature. Cause The noise occurs due to friction between the lining and the brake caliper. Remedy Removal of brake linings Cleaning all contact points on brake lining and brake caliper/carrier Greasing contact points (green areas) between brake lining and guide of brake caliper with heat-resistant lubricating paste A001 989 87 51
• 10231032Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead.
• 10228824Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2021 GLA-Class and GLB-Class (156/247 platform) vehicles, the transmission bearing cap cover does not correspond to current specifications. Over time, the transmission bearing cover may loosen, which may result in minor oil loss. An instrument cluster transmission light will still alert the user if it falls below the threshold and alert the driver if the transmission oil overheated. The indicator light will alert the driver to drive with caution. A risk of fire can be ruled out. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the transmission bearing cover.
• 10228813Complaint Staining on door trim strips and top and bottom trim elements on rear side windows. See example pictures 1, 2 and 3. Cause Damage to protective coating of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the problem cannot be rectified by polishing the trim bars with the polishing paste. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
• 10228807Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams.
• 10227143Complaint Squeaking noise from area of input shaft of electric steering Cause Inadequate lubrication. Remedy Grease/lubricate sealing area of input shaft. The steering components can be greased/lubricated while they are still installed
• 10217163Complaint The Apple Carplay interface cannot be controlled via the center console touchpad or the right-hand steering wheel touchpad. Cause A setting on the iPhone may prevent control via the touchpad Remedy To remedy on the affected iPhone, navigate to "Settings" -> "Accessibility" -> "Touch" and turn the "BackTap" option OFF.
• 10217159Complaint - Vehicle cannot be unlocked/ vehicle does not start - Display message in instrument cluster "Battery - Start Engine - see Operator's Manual Cause Root cause is a bus keepawake in either the Headlight control unit or in one of the following: ALC, IC, SAM, PTCU, ESP. Additionally, the quick test will show U116000 "A bus keepawake control unit has been detected" in the electronic ignition switch (EZS) control unit for this root cause. Remedy Eliminate bus keep awake issue flash new software where available:
• 10217158Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. - Instrument panel support - Steering column switch module If the cause of the noise can be narrowed down to the steering column, create a PTSS case
• 10215016Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2020-2022 A-Class, C-Class, CLAClass, GLA-Class, GLB-Class, GLC-Class, GLE-Class, and GLS-Class (118, 167, 177, 205, 247, and 253 platform) vehicles, the mobile phone cradle control unit software does not correspond to the current series production specifications. It is therefore possible that the inductive charging function may not work as intended. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the mobile phone cradle control unit software.
• 10210929Complaint Volume and bass level too low Cause Current sound amp (N40/3) software release. Important: On vehicles with standard sound, the rear subwoofer (H21/35) emits the engine sound only (if equipped with M139 engine) On vehicles with code 853 (Advanced Sound) or 810 (Premium Sound), the rear subwoofer (H21/35) emits not only the engine sound, but also entertainment sound Remedy Perform a software update of the sound amp (N40/3) to the latest available version. Note: Do not replace any parts as this will not remedy the complaint.
• 10209877Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.
• 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
• 10205812The customer may note that the Dashcam feature is inoperable with one of the following complaints.
• 10205809The customer may note that the Dashcam feature is inoperable with one of the following complaints:
• 10205806Upon selecting navigation, the central display may show the following message: "Map data does not match with your system. Please insert a medium containing the corresponding map data". the navigation menu cannot be opened.