2017 Mercedes-Benz GLS350D
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLS350D › 2017
These records cover every 2017 Mercedes-Benz GLS350D. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2017 Mercedes-Benz GLS350D. Newest first.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205835Model series 167 noise on B/C/D pillars.
- 10205257Model indicator index.
- 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10195220For plug in hybrid and electric variants: Complaints about the electric range
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10181203Replace tank filler recess and information labels
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10172683Information Label on Tire Sealant
- 10170531167 GLS headlight low beam fault
- 10167487Minor leaks at the oil duct of the left or right cylinder head of engines 157, 276 and 278. 1. Left cylinder head: Oil passage plug hole on left beside mechanical vacuum pump. 2. Right cylinder head: Oil passage plug hole below high-pressure pump housing.
- 10158372Vehicle does not start, battery discharged.
- 10157080Correct Torque of Front Left and Right Torsion (Stabilizer) Bar Linkage Nut
- 10157079Correct Torque of Front Left and Right Torsion (Stabilizer) Bar Linkage Nut
- 10157078Replace Fasteners for Rear Axle Camber Adjustment