2007 Mercedes Benz R500

Recalls

2 recalls name the 2007 Mercedes Benz R500. Newest first.

• Service brakes, hydraulic › Power assist › Vacuum

  Apr 26, 2024NHTSA 24V29800015,604 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML, GL, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.

  Risk and remedy

  Risk

  Reduced brake performance or brake failure can increase the risk of a crash.

  Remedy

  Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed on May 24, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MMUSA's number for this recall is 2024050001/2. This recall is an expansion of previous recall number 22V-315.

  Full recall details →

• Service brakes, hydraulic › Power assist › Vacuum

  May 9, 2022NHTSA 22V315000350,294 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML-Class, GL-Class, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.

  Risk and remedy

  Risk

  Reduced brake performance or brake failure can increase the risk of a crash.

  Remedy

  Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed June 30, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2022050014, 2022050015 2022090006, & 2022090007.

  Full recall details →

Owner complaints

What owners report most

1. Fuel system, gasoline1
2. Suspension1
3. Vehicle speed control1
4. Visibility/wiper1

Latest complaints

• May 8, 2017DC153,525 mi
  Suspension · Vehicle speed control · Visibility/wiper

  My air shocks keep going out this seems to be a known issue with mercedes it happen while I was driving almost had an accident. my car IS now park sitting sideways.

• Mar 26, 2010AE36,979 mi
  Fuel system, gasoline
  Mercedes R500 stalls without warning while driving on freeway. each time causing a total shut down of the car. this has happened 4 times in the last 7 months we have had the car. each time we are able to coast to the side of the freeway but IS just luck that we have not been in a accident yet.…

  Mercedes R500 stalls without warning while driving on freeway. each time causing a total shut down of the car. this has happened 4 times in the last 7 months we have had the car. each time we are able to coast to the side of the freeway but IS just luck that we have not been in a accident yet. each incident has been while on a family trip traveling on the interstate . All but one time, once it had been loaded onto the tow truck and delivered to the mercedes dearlership the car started and ran perfectly! we have taken it to the mercedes dearlership each time for service but they have been unable to diagnose the problem. we have had the fuel filter replaced, drive sensors replaced and the fuel line cleaned out but this just happened again yesterday again with my children in the car traveling at highway speeds!!

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10166978Engine diagnosis warning lamp lights up - Fault code entry (FC) 14A600 or 14A700
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
• 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
• 10166099Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
• 10166080The pneumatic 4-way lumbar support fails. Lumbar support pockets cannot be filled up or they drain.
• 10158329Oil in engine wiring harness
• 10135653Procedure in case of slight oil traces on TRANSMISSION 722.9
• 10135649Procedure in case of slight oil traces on TRANSMISSION 722.9
• 10135632Fault in particulate sensor
• 10135628iPhone mobile phone: Various complaints after software update to iOS8
• 10052151Xentry (mercedes): rattling noise coming from the area of the steering column tube system, when driving over rough road and when accelerating or braking, there would be cracking noises. Models 164, 251. No model years listed.
• 10041024Mercedes-benz: the fuel level indicator IS wrong.
• 10037408Mercedes-benz: shock absorber procedure.
• 10033074Xentry: outside door handle no longer returns to end position. Due to a bent pin in the dynamic balancer, the support spring of the bearing bracket can slide out of place or become unhooked. Models 164, 251, 166, 204, 212. No model years listed. Updated 2/1/12. Updated 10/3/12. Updated 10/21/13.
• 10033071Mercedes benz: adjusting wiper arms. If you receive reports on certain vehicles of wipers chattering/noisy, proceed as follows: inspect wiper blades/inserts for wear and replace; thoroughly clean windshield; verify use of correct washer fluid; check washer nozzle adjustment; check wiper arm angle adjustment; and record values per applicable model; if required, adjust wiper arm angle. Models 164/251. No model years listed.
• 10033070Xentry (mercedes): engine warning lamp IS currently on or was on and a delay fault of the camshaft adjust to current or stored in the engine control unit. Models 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, and 403. No model years listed.
• 10032727Mercedes: following fault codes are entered in the control unit and displayed-fc5320 drain valve:open circuit or insufficient valve current in models series 211, 219; fc5260 drain valve open circuit or insufficient valve current in model 221; fc5250 drain open circuit or insufficient valve current in model series 251, 164. Defective connecting cables to drain valve at airmatic compressor. This results in the setting of the fault codes. No model years listed.
• 10032707Mercedes: ensuring unobstructed movement for the fuel level sensor. When installing the left or right fuel level sensor, it IS essential for it to have unrestricted, unobstructed movement.
• 10032568Mercedes benz service campaign: see document search button for owner letter. Software calibration number (scn) coding; engine control module. The vehicles fuel tank leak diagnosis system may have been inadvertently deactivated during a visit to the workshop. This may cause the affected vehicles to fail to meet the statutory requirements for inspection and or maintenance (emissions inspection).
• 10030929Mercedes: corrosion protection coatings for brake components and hardware may be damaged and or stripped away if highly concentrated acid based cleaners are used. Once the corrosion protection IS damaged or removed the brake components and or hardware can begin to corrode. Include all models and model years.
• 10028686Mercedes: air matic visit workshop displayed within instrument cluster. Models 164, 211, 219, 221 and 251. Included 4matic, AMG (compressor) AMG, bluetec and wagon. Model years unknown. Updated 9/18/09.
• 10028668Mercedes: active head restraints activate for no reason. This may be caused by damage to the seat wiring harness causing a short circuit. Models 164 and 251. Model years unknown. Updated 9/18/09.
• 10028646Mercedes: groaning or dull, heavy cracking noises from steering shaft area. When turning steering wheel or moving off or braking. This may be emanating from the bearing and housing of upper steering shaft (firewall pivot point) or steering coupling (lower steering shaft). Models 164 and 251. Model years unknown.
• 10028645Mercedes: chrome plating peeling on decorative caps on the steering wheel spokes, this IS due to less than optimal adhesion between chrome plating and base material. Models 164 and 251. Model years unknown.
• 10028026Mercedes: replace v belt upper guide pulley. The v belt upper guide pulley optimized for noise reduction IS available. The dealer will replace upper guide pulley at the next workshop visit.
• 10028025Mercedes: stop/tail light not illuminating with dtcs 9102, 9103, 9106, 9107, 9126, 9127 or 9136. (Vehicles without led tail lamps) updated 5/13/09. Updated 4/20/11. Repair does not apply to led tail lamps.
• 10028024Mercedes: check air suspension compressor and replace if necessary. Insufficient air pressure in the air suspension system may result from damage to the pressure disk in the air suspension compressor.
• 10025648Rattling/thumping noise on rough roads and/or knocking noise when moving steering in both directions on all model 164 and 251 vehicles. Model years unknown.
• 10023791Models ml350, ml500, ML63, ml320, ml550, gl450, gl320, gl550, R350, R500, R63, R320 - my2007-2008. Install rear enterainment software.
• 10023784Models E320, E500, E55, E350, E550, E63, ml350, ml500, ML63, ml320, ml550, gl450, gl320, gl550 with diesel engine om 642 my 2006-2007 -- update engine control module software.
• 10023491Mercedes-benz - procedure for replacing fuel pump and fuel filter modules . Models ML63, ml320, ml350, ml500, ml550, gl320, gl450, gl550, R63, R320, R350, R500. Model year all.

Every Mercedes Benz R500 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.