2014 Mercedes-Benz S550
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › S550 › 2014
These records cover every 2014 Mercedes-Benz S550. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2014 Mercedes-Benz S550. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 SL550, 2013-2014 SL63 AMG, 2014-2016 E350, 2014 E350 Cabriolet, E350 Coupe, 2014-2015 S550, 2015 E350 Bluetec, 2015-2016 E400, 2016 E550 Coupe, and Maybach S600 vehicles manufactured August 23, 2012, to August 14, 2015. The affected vehicles use an electric power steering system that…
Risk and remedy
Risk
If the control unit pins lose connection, there would be a loss of electric power steering assist, increasing the risk of a crash. The increase in pin contact resistance can also increase the risk of a fire, even while the vehicle is parked and ignition is off.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering control unit, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (Mercedes-Benz) is recalling certain model year 2014 S550 vehicles manufactured April 11, 2013, through October 14, 2013. In the affected vehicles, the front seat belt anchor might not be installed correctly allowing it to come loose in a crash.
Risk and remedy
Risk
If the seat belt anchor comes loose, in the event of a crash, the occupant may not be properly secured, increasing the risk of injury.
Remedy
Mercedes-Benz will notify owners, and dealers will inspect and correct the front seat belt anchor fitting, as necessary, free of charge. The recall began on December 20, 2013. Owners may contact Mercedes-Benz at 1-800-367-6372. Mercedes-Benz's recall number is 2013110008.
Owner complaints
24 complaints4 involved a crash2 injuries
What owners report most
Latest complaints
- Seat belts
We almost got into crash the other day, our 8-year-old kid got our attention that rear seatbelt got very loose and did NOT retract back at all. he almost hit his head. when I asked him if it has been like this he said no, it was tight when I buckled it in. We tried several times to retract it…
We almost got into crash the other day, our 8-year-old kid got our attention that rear seatbelt got very loose and did NOT retract back at all. he almost hit his head. when I asked him if it has been like this he said no, it was tight when I buckled it in. We tried several times to retract it manually with no luck. I checked online and I have seen people complaining about the same thing. we have been lucky we didn't hit the other car then my child will be seriously injured. This is a very serious safety requirement. I hope Mercedes Benz will take this very seriously as well, before others get hurt.
- Engine and engine cooling
The contact owns a 2014 Mercedes Benz S550. The contact stated that while the vehicle was idling, there was an abnormal ticking sound coming from the vehicle. There was no warning light illuminated. The contact became aware of oil spots on the driveway after parking the vehicle. The vehicle was…
The contact owns a 2014 Mercedes Benz S550. The contact stated that while the vehicle was idling, there was an abnormal ticking sound coming from the vehicle. There was no warning light illuminated. The contact became aware of oil spots on the driveway after parking the vehicle. The vehicle was taken to a dealer where an inspection indicated that the oil filter housing was defective and needed to be replaced. The contact was then given a list of other parts associated with the oil filter housing that also needed to be replaced. The manufacturer was notified of the failure and was informed the contact that the VIN was not under recall. The vehicle was not repaired. The failure mileage was 89,677.
- Unknown or other
Unknown
- Service brakes, hydraulic › Foundation components › Disc › Pads
The contact owns a 2014 Mercedes-Benz S550. The contact stated while the vehicle was parked, the contact became aware that the brake pads were corroded. There was no warning light illuminated. The vehicle was taken to an independent mechanic where it was confirmed that the brake pads were severely…
The contact owns a 2014 Mercedes-Benz S550. The contact stated while the vehicle was parked, the contact became aware that the brake pads were corroded. There was no warning light illuminated. The vehicle was taken to an independent mechanic where it was confirmed that the brake pads were severely corroded. The contact was informed that the brake pads needed to be replaced. The vehicle was not repaired. The vehicle was taken to the dealer where the same diagnostic was provided to the contact. The contact was informed that the brake pads needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 70,000.
- Seat belts
Rearvpassenger seat just stopped working. Won't retract.
- Suspension
The vehicle dropped at front axle areas on both sides. The next message stated "Vehicle to Low". Vehicle is available for inspection upon request. Could not drive regular speed limit almost got rear ended. Reproduced i am not sure, there is however about 3 manufacturer communications on this…
The vehicle dropped at front axle areas on both sides. The next message stated "Vehicle to Low". Vehicle is available for inspection upon request. Could not drive regular speed limit almost got rear ended. Reproduced i am not sure, there is however about 3 manufacturer communications on this issue. There have not been any inspections relating to this issue with insurance. The manufacturer Mercedes previously inspected and replaced several issues relating to suspension on this vehicle type. There are at least 40-60 product model vehicle types that have this issue. The vehicle i drive is one of them. The warning lamp came on when starting the car, the front end did not rise as it was expected to , warning lamp stated Vehicle level too low
- Fuel/propulsion system · Power train · Steering
What component or system failed or malfunctioned, and is it available for inspection upon request? -Steering :Electrical Power Assist , Drive Shaft
- Forward collision avoidance › Adaptive cruise control · Forward collision avoidance › Automatic emergency braking · Lane departure › Blind spot detection
Pre safe disabled then Blind spot disabled then cruise control disabled this occurs in heavy rain had the dealer check it told they could not duplicate the problem told them this is a dangerous problem in heavy weather as you do have blind spots in the s class and you do need the system to work.once the weather improves or the heavy rain subsides the system restores itself
- Unknown or other
At approximately 0030 friday august 07, I was travelling 65 mph north bound on the ca215/60 freeway, there was little traffic. I heard what sounded like a gunshot, then a crincling glass sound and finally a whooshing of air I would soon see was a gaping hole where my closed panoramic sunroof use to…
At approximately 0030 friday august 07, I was travelling 65 mph north bound on the ca215/60 freeway, there was little traffic. I heard what sounded like a gunshot, then a crincling glass sound and finally a whooshing of air I would soon see was a gaping hole where my closed panoramic sunroof use to be. I exited the freeway at the next exit and pulled into a gas station, got out of the car and upon inspecting the car found a huge hole where my panaramic sunroof use to be. I also made a video available at request.
- Latches/locks/linkages › Doors › Latch
TL* the contact owns a 2014 mercedes-benz S550. The contact stated that the doors failed to lock manually or with keys. The contact called mercedes-benz of cutler bay (10701 sw 211 st, cutler bay, fl 33189, (786) 232-0364) to inform the dealer of the failure. The vehicle was not diagnosed nor…
TL* the contact owns a 2014 mercedes-benz S550. The contact stated that the doors failed to lock manually or with keys. The contact called mercedes-benz of cutler bay (10701 sw 211 st, cutler bay, fl 33189, (786) 232-0364) to inform the dealer of the failure. The vehicle was not diagnosed nor repaired. The manufacturer was notified of the failure but offered no additional assistance. The approximate failure mileage was 55,000.
- Air bags
TL* the contact owned a 2014 mercedes-benz S550. While the contact's vehicle was idling at a red light, another vehicle ran a stop sign and t-boned his vehicle. None of the frontal air bags deployed. The police was present and filed report number: 190911002273. The fire department was also present.…
TL* the contact owned a 2014 mercedes-benz S550. While the contact's vehicle was idling at a red light, another vehicle ran a stop sign and t-boned his vehicle. None of the frontal air bags deployed. The police was present and filed report number: 190911002273. The fire department was also present. There were no injuries; however, medical attention was sought later. The vehicle was towed to a body shop. The dealer was not contacted. The manufacturer was notified of the failure. The insurance company deemed the vehicle destroyed. The vehicle was not diagnosed. The approximate failure mileage was 50,000. *Dt *as
- Wheels
This past thursday evening (december 13, 2018) around 10:00 pm, I was driving (with my wife in the passenger seat) down a curvy stretch of road on sunset boulevard in beverly hills, when I suddenly heard a loud thumping sound and immediately felt violent vibrations through the steering wheel.…
This past thursday evening (december 13, 2018) around 10:00 pm, I was driving (with my wife in the passenger seat) down a curvy stretch of road on sunset boulevard in beverly hills, when I suddenly heard a loud thumping sound and immediately felt violent vibrations through the steering wheel. since we were traveling at a relatively low speed of 30 mph, I was immediately able to re-gain the control of my vehicle and was able to pull over safely. once I got out of my vehicle, I immediately noticed that the front right wheel rim had completely broken into two halves. I was shocked and very surprised because nothing could have possibly explained why this wheel completely broke in the manner that it did. we were extremely fortunate that there were no other vehicles around us at the time the wheel broke, or that we were not on the highway traveling at much higher speeds, otherwise the results would have been fatal with even a possibility of significant injury or even loss of life. a complete report with pictures and cause of rapid fracture of the rim as a complaint was provided to mercedes dealership and corporate, they are refusing to admit to any material defect and liability.
- Steering
According to the recall nhtsa campaign ID number: 16v899000 and the vehicle inspection report from the local mercedes dealership show as an identical issue. however, my vehicle IS not identified as apart of the recall. the recall states the issue IS due to the steering control unit not being…
According to the recall nhtsa campaign ID number: 16v899000 and the vehicle inspection report from the local mercedes dealership show as an identical issue. however, my vehicle IS not identified as apart of the recall. the recall states the issue IS due to the steering control unit not being soldered properly. difficult to think this falls under normal wear and tear. I will get the repair done begrudgingly, though it would be nice if mercedes would have stood behind its recall.
- Exterior lighting › Headlights · Visibility/wiper
TL* the contact owns a 2014 mercedes-benz S550. While driving various speeds, the headlights failed to illuminate the roadway. The vehicle was taken to mercedes-benz of north palm beach (9275 fl a1aalt, north palm beach, fl 33403) where it was diagnosed that the headlight assembly and control…
TL* the contact owns a 2014 mercedes-benz S550. While driving various speeds, the headlights failed to illuminate the roadway. The vehicle was taken to mercedes-benz of north palm beach (9275 fl a1aalt, north palm beach, fl 33403) where it was diagnosed that the headlight assembly and control module needed to be replaced. The vehicle was not repaired. The vehicle was previously repaired, but the failure recurred. The manufacturer was made aware of the failure and stated that the issue needed to be handled between the contact and the dealer. The failure mileage was approximately 18,497. The vin was not available.
- Visibility › Sun/moon roof assembly
TL* the contact owns a 2014 mercedes-benz S550. While driving 50 mph merging on the interstate, the sun roof shattered without warning. The vehicle was taken to the local dealer (mercedes-benz of mobile, 3060 dauphin st, mobile, al, 36606) where it was confirmed that the sun roof failed. Due to the…
TL* the contact owns a 2014 mercedes-benz S550. While driving 50 mph merging on the interstate, the sun roof shattered without warning. The vehicle was taken to the local dealer (mercedes-benz of mobile, 3060 dauphin st, mobile, al, 36606) where it was confirmed that the sun roof failed. Due to the failure, the vehicle also sustained body damage to the hood and trunk. The manufacturer was stated that they would give the contact a call back and send an investigator. The contact was referred to the dealer. The vehicle was not repaired. The contact also sustained a cut on the right side of the face due to the shattered glass. The contact did not receive medical attention. The failure mileage was approximately 70,000.
- Service brakes
Rear brake pads incorrectly installed from the factory. Both inside brake pads were installed on the rear caliper found that pads on the right rear were worn down to 4-5MM also found that right rear rotor has uneven grooves from brake pads.
- Steering
When making turns both left and right, there IS a moaning noise heard. Cause: lower engine compartment center and rear, steeering coupling, rubber bellows on steering.
- Unknown or other
Backup lights on this car are totally useless. Dealer says no brighter bulbs are available. dangerous situation. Backed into a mailbox and did $700.00 in damage. Please advise what I should do.
- Tires
I have had three run flat goodyear tires blow outward side walls rendering the vehicle in operable. All three occurred while driving on interstate highways within normal speeds of 70 to 75 mph. the first tire was replaced in fl in may - left front, the second on august 9TH in nj same left front…
I have had three run flat goodyear tires blow outward side walls rendering the vehicle in operable. All three occurred while driving on interstate highways within normal speeds of 70 to 75 mph. the first tire was replaced in fl in may - left front, the second on august 9TH in nj same left front, and the third on august 12TH in waterbury ct right front. all three tires had outward sidewall lateral destruction of 4 to 6 inches. the decompression was instantaneous the tires were 1, oem, and 2 and 3 replacement for oem all same make and model goodyear. the vehicle IS a mb 2014 S550 sedan with 20 inch rims. there IS noi defect on any of the rims. the serial or vin IS [xxx] net wgt 4,773 lbs.. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr
- Power train · Service brakes · Suspension › Rear · Visibility › Rearview mirrors/devices › Exterior
TL* the contact owns a 2014 mercedes benz S550. While driving approximately 10 mph, the vehicle downshifted and suddenly there was a hard shift when the accelerator pedal was depressed or when stopped at a traffic light. The contact also noticed that there was a loud noise near the rear of the…
TL* the contact owns a 2014 mercedes benz S550. While driving approximately 10 mph, the vehicle downshifted and suddenly there was a hard shift when the accelerator pedal was depressed or when stopped at a traffic light. The contact also noticed that there was a loud noise near the rear of the vehicle. The contact also noticed that the tilt function feature on the right passenger mirror failed. When functioning properly, the right passenger mirror tilted downward and to the right when the vehicle was placed in reverse; therefore, the driver could see all objects to the rear passenger side of the vehicle and in the vehicle's blind spot. The mirror failed to return to the driver's setting after shifting the vehicle into drive after being in reverse. The failure recurred multiple times. The dealer stated that the rear suspension system and the rear brakes needed to be replaced. The dealer also stated that they were unable to locate a failure with the mirror. The rear suspension system and the rear brakes were replaced; however, the failure with the mirror persisted. The manufacturer was notified of the failures. The approximate failure mileage was 2,000. The vin was unavailable.
- Unknown or other · Visibility/wiper
This vehicle was purchased new in 2014. the vehicle has a reverse tilt function feature on the right passenger mirror. when functioning properly, the right passenger mirror tilts downward and to the right when the vehicle IS placed in reverse so that the driver can see all objects to the right…
This vehicle was purchased new in 2014. the vehicle has a reverse tilt function feature on the right passenger mirror. when functioning properly, the right passenger mirror tilts downward and to the right when the vehicle IS placed in reverse so that the driver can see all objects to the right rear of the vehicle (in the vehicle's blind spot). once the vehicle IS shifted into drive, the right mirror IS supposed to return to the driver's (memory) setting position for the mirror so that the driver IS able to see out of the right mirror when driving on the highway. the mirror on this vehicle fails to return to the driver's (memory) setting after shifting the vehicle into drive after being in reverse. the mirror remains in the downward and to the right position thus leaving the driver completely unable to see out of the mirror when driving on the highway. the driver IS forced to take his/her eyes off of the road, and the surrounding vehicles, to manually adjust the mirror thus placing the driver and all passengers at a significant risk of injury. while it IS unconfirmed, this vehicle was involved in a side-swipe type motor vehicle accident, and it IS suspected that this mirror defect was a contributing cause to the accident. mercedes-benz USA IS aware of this defect and IS aware that at least two cases have been reported in the united states in the 2014 S550 model. Mercedes-benz USA IS also aware that this defect exists in the 2015 S550 model. mercedes-benz USA has been given numerous opportunities to cure this defect and it has failed/refused to make the repair, thus exposing all 2014 and 2015 S550 drivers, and their passengers, to a significant risk of injury.
- Fuel/propulsion system
Aggravating noise associated with high pressure fuel pumps, tick, tick, ticking noise at any speed. Complained to dealer, but despite exchanging pumps, noise persists. Complained to mbusa, was told this was a 'normal noise'. Sounds like an oxymoron to me. Very disappointed with car noise and response to my plea for help. *tr
- Equipment adaptive/mobility · Vehicle speed control
I was on a test drive. cruise control was on. speed was 55mph. van pulled in front of me and decelerated. mercedes maintained speed and was closing rapidly. applied brakes hard to avoid rear ending van. *tr
- Air bags · Electrical system · Structure › Body
I purchased a new 2014 mercedes S550 and the day after purchase, the airbag malfunction light came on. I set up an appointment to have this corrected, and was told it was fixed. a couple of weeks later, I was traveling at approximately 20mph, approaching an intersection where I did not have a…
I purchased a new 2014 mercedes S550 and the day after purchase, the airbag malfunction light came on. I set up an appointment to have this corrected, and was told it was fixed. a couple of weeks later, I was traveling at approximately 20mph, approaching an intersection where I did not have a stop sign. I noticed a large SUV traveling east bound at excessive speeds (guessing 35-40), which did not appear to be stopping, but could not stop in time to avoid the collision. the SUV impacted the driver's side of my vehicle at full speed. my vehicle spun and was hit again at the side and rear driver's side. I was pushed over the curb and into a snow bank where I eventually stopped after hitting the yield sign. I was trapped in my vehicle as I had carved thru the snow and all doors were blocked. the damage to the vehicle was on the driver's side front, side and back. the hit was hard enough to cause frame damage to the vehicle, needing frame repair. there were no airbags deployed during the crash and given the previous malfunction with the airbag system, this was a major concern for me. I notified mercedes benz of the issue, and it wasn't until several requests that they responded. they sent someone to the body shop to look at the car and confirmed there IS frame damage; however, stated it was not hard enough of a hit to trigger airbag deployment. I have a hard time understanding how it can be hard enough to cause frame damage yet not trigger airbag deployment? this IS a completely redesigned vehicle and mine was one of the first on the road. I am fearful that this IS a larger issue that IS not being addressed, or uncovered, since this IS a recently released model. as a result of the impact, I sustained injuries to my neck, back and left elbow. I am hoping this could get address to avoid future injuries, or death, to other drivers and passengers. thank you. *tr
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10240203This NCU replaces the prior NCU issued on May 11, 2023, and clarifies replacement part information. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, is extending the warranty coverage on the catalytic converter system in certain Model Year (MY) vehicles fitted with the M278 8-cylinder engine listed below: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 13 years / 156,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 144,000 miles (whichever occurs first) - MY2013: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 132,000 miles (whichever occurs first) - MY2014 MY2020: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first)
- 10238430Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2014-2020 S-Class (217 and 222 platform) vehicles, the incorrect pilot bushings may have been installed in the front axle tension struts. It is possible that noises and an increased wear of the pilot bushings may occur. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will check the pilot bushings on the front axle tension struts, and replace if necessary.
- 10237240This extended warranty applies to the following condition that may necessitate the repair or replacement of the catalytic converter system and is related to: A check engine Malfunction Indicator Lamp (MIL) may illuminate due to sulfur contamination in the catalyst.
- 10233794Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).
- 10233778In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below as follows: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 120,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 120,000 miles (whichever occurs first) - MY2013 MY 2016: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first) This extended warranty applies to the following condition that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinderhead) related to: Over time, increased lateral forces may lead to wear in the valve guide and/or seat ring. This issue could potentially cause combustion misfire for cylinder 1 through 8 (right and/or left cylinder head), resulting in an activation of the check engine Malfunction Indicator Lamp (MIL) .
- 10209877Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does not necessarily need to be replaced. A discharged battery may be recovered with no permanent damage. Remedy Follow guided tests as described.
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205803The mobile phone address book may not be transferred completely to the multimedia system COMAND, Audio 20, or MBUX. The contact list may not be fully populated and in some instances, the call list will display telephone numbers but no names.
- 10205266Map pocket on front seat backrest trim does not close.
- 10205263Trunk lid closes too quickly.
- 10205252High voltage battery warning message in instrument cluster.
- 10205242Navigation system permanently displays "Activating".
- 10205241Navigation system permanently displays "Activating".
- 10205233Mobile phone cotacts are not transferred completely.
- 10205154Gasket may settle causing a slight oil leak.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179956Xentry Battery Tester results disagree with workshop assessment
Every Mercedes-Benz S550 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.