2016 Mercedes-Benz S550 4MATIC

Recalls

1 recall names the 2016 Mercedes-Benz S550 4MATIC. Newest first.

• Communication

  Nov 1, 2019NHTSA 19V78700024,226 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…

  Risk and remedy

  Risk

  An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

  Remedy

  MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

  Full recall details →

Owner complaints

What owners report most

1. Unknown or other6
2. Vehicle speed control2
3. Visibility/wiper2
4. Wheels2
5. Visibility1
6. Service brakes1
7. Air bags1

Latest complaints

• May 21, 2024NJ
  Wheels
  I got this certified car from Mercedes Benz dealer. I have driven it sparingly for less than 10K miles without really any hitting any bumps or potholes . After a recent service [XXX] 2024 at a MB dealer, I was told that 2 wheels were cracked 1 front & 1 back . I took it to another MB dealer (MB…

  I got this certified car from Mercedes Benz dealer. I have driven it sparingly for less than 10K miles without really any hitting any bumps or potholes . After a recent service [XXX] 2024 at a MB dealer, I was told that 2 wheels were cracked 1 front & 1 back . I took it to another MB dealer (MB Morristown, NJ) to change the wheels & they advised that all 4 wheels were cracked, & one wheel had 3 cracks. These are premium AMG staggered wheels & without a doubt there is genuine design issue or defect to wheels which at high-speed could crack & crumble causing major injury & destruction to property. I have all the service records regarding this issue INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• Nov 24, 2020MA40,000 mi
  Wheels

  I have now experienced cracks on three separate tire rims. The car has less than 41,000 miles.the tires are low profile, run flat tires and the rims appear to be aluminum and faulty.

• Oct 24, 2020FL34,000 mi
  Unknown or other
  2016 mercedes cls550... I bought this car used and I've had it for about 6 months. I've already had a seizure in the car and was found slumped over by florida highway patrol at a dead stop with the car running and the air on and I woke up in the hospital. Something IS wrong with the air conditioner…

  2016 mercedes cls550... I bought this car used and I've had it for about 6 months. I've already had a seizure in the car and was found slumped over by florida highway patrol at a dead stop with the car running and the air on and I woke up in the hospital. Something IS wrong with the air conditioner causing carbon monoxide poisoning IS the only thing that I can put together. The hospital obviously would not think that it was because of my air conditioner. They did a cat scan everything fine . They did a covid test everything and I was cleared and out the door in 5 hours. I have put this together and figured it out myself. I've had nothing but a foul sour disgusting odor coming through my air conditioner and I have almost passed out on three other occasions same exact feeling up until I had my seizure. Something IS definitely wrong and I went ahead and replaced my cabin filter. I still have the one that was in the car. I want compensation for the damage that has become of my body because of this car. I heard that there has been many lawsuits for the air conditioner on this model and other models but never anything that would kill someone. I'm afraid to drive the car. I've had a tester used in my car and it picked up carbon monoxide. I am going to sue the balls off of mercedes and the dealership that sold me the car for not fixing this problem or any recalls that were put out. Anyways I can almost smell the exhaust fumes on top of a sour smell. Good thing I'm smart enough to put two and two together. I expect somebody to get back to me asap as I will be seeking legal representation and I will bring this public.

• Aug 14, 2020MI25,000 mi
  Visibility/wiper

  Heard a loud bang while driving down the highway and didn't know what it was until returning home and looked up and saw the rigid crack from front to the back on the panoramic glass. There are no indications of debris hitting the glass as there are no chips.

• Jun 18, 2020NY25,600 mi
  Visibility/wiper
  Vehicle's front windshield spontaneously cracked overnight while vehicle as parked in a locked private garage. crack originates at top of windshield frame where body torques the glass and continues through advanced driver assistance systems, ending up in driver's line-of-sight. no visible point…

  Vehicle's front windshield spontaneously cracked overnight while vehicle as parked in a locked private garage. crack originates at top of windshield frame where body torques the glass and continues through advanced driver assistance systems, ending up in driver's line-of-sight. no visible point of impact on damaged area of glass. driver assistance and safety systems are affected by the stress crack, rendering them non-functional. dealer investigated and determined that stress crack was due to a defect in manufacturing and installation of the glass, not due to any impact or road debris. however, manufacturer denied coverage under new vehicle warranty (4yr./50,000 mi), stating that glass defects are only covered for 1 yr/12,000 mi. *Tr

• Jun 13, 2020FL10,100 mi
  Unknown or other · Visibility › Sun/moon roof assembly

  Panoramic sunroof cracked with no known cause. *tr

• Jan 13, 2020NE
  Air bags

  TL* takata recall. The contact owns a 2016 mercedes benz S550 4matic. The contact stated that the recall notice for nhtsa campaign number: 19v01000 (air bags) was received. After contacting the local dealer (unknown), the contact was informed that the parts needed to repair the vehicle were not available. The contact had not experienced a failure. Vin tool confirms parts not available.

• Apr 3, 2016ME50 mi
  Service brakes · Unknown or other · Vehicle speed control
  From 2014 through 2016 the intelligent drive and the driver assistance package does not work. I keep saying the S550 thinks 200 feet IS 90 feet and 100 feet IS 30 feet. what I mean to say IS the systems think 90 feet distance IS 200 feet away and 30 feet IS 100 feet away. It does not measure the…

  From 2014 through 2016 the intelligent drive and the driver assistance package does not work. I keep saying the S550 thinks 200 feet IS 90 feet and 100 feet IS 30 feet. what I mean to say IS the systems think 90 feet distance IS 200 feet away and 30 feet IS 100 feet away. It does not measure the distance properly. It could be, and most likely, a programing issue. It IS the same on all the 2014 through 2016 s550's I have tried. The other thing it does with the distronic cruise control IS when it starts to brake, the distance set decreases and the car speeds up and again the distance set decreases and the car speeds up and so on. It changes the distance ( you can see it happen in the in the menu setting on the speed and tachometer screen) as soon as the car autonomously brakes. Set it at 200 feet and in reality it IS 90 feet and as soon as it brakes the distance to keep instantly drops to just under what it IS set at so the car thinks the danger IS over and speeds up again and then brakes again. And you keep getting closer and closer to the car in front because the set distanced keeps changing and you have to brake so you do not hit the car in front because the S550 won't. I hope this makes sense. It IS easier to show with the distance graphic up on the screen. The whole system IS completely screwed up. As IS the led lighting system in the snow and freezing rain and slush. Cannot drive it at night in a winter storm. It all happens around town to highway speeds. I was actually told by the service manager for the distronic cruise to work I have to be driving faster than 75 mph. My 2007 S550 4 matic's distronic and autonomous braking worked perfectly.

• Jan 14, 2016ME100 mi
  Unknown or other
  All the safety complaints in the past two forms happen in all the 2014,2015. And 2016 mercedes S550. The cars are suppose to practically drive themselves. It even has steering assist that keeps the car centered in the lane and will even steer around curves. it IS suppose to keep pre set distances…

  All the safety complaints in the past two forms happen in all the 2014,2015. And 2016 mercedes S550. The cars are suppose to practically drive themselves. It even has steering assist that keeps the car centered in the lane and will even steer around curves. it IS suppose to keep pre set distances from the car in front that you can set between 100 and 200 feet. It IS suppose to stop before hitting an object in front of the car. None work. What IS going to happen when in 2020 when the car mercedes build will actually drive itself. If they cannot get this simple safety features to work correctly in my car, how IS it going to work when it mass produces cars that totally drive themselves.. The driver assistance pkg. Works like it was never installed in my car, how will having the car take over more control work. If I do not feel safe in my car now god help us all. When all the cars drive themselvews. Sure the ones they are driving as test cars work. They were hand built. What happens when they are mass produced whith other countries making the parts. It sounds as if mercedes IS going to have a massive recall campaign with the safety features that do not work now.

• Jan 14, 2016ME45 mi
  Unknown or other
  Collision prevention assist plus does not work. It's suppose to work from 4 mph to 65 mph.it does not recognize stopped cars or objects in it's path.it's suppose to autonomously apply the brakes to help prevent collisions with other vehicles. It never intervenes.when a car cuts me off or pulls out…

  Collision prevention assist plus does not work. It's suppose to work from 4 mph to 65 mph.it does not recognize stopped cars or objects in it's path.it's suppose to autonomously apply the brakes to help prevent collisions with other vehicles. It never intervenes.when a car cuts me off or pulls out in front of me or stops in front of me,the safety features do not intervene.i have to brake hard to avoid a collision every time. A warning tone,the seat belts should pre-tension,place the seats in a more favorite position conclusive to an accident, close the windows & sunroof.brakes before you have time to put the brakes on. It does non of those things.i have had a 2007 S550 with all the safety options & they worked perfectly every time.it would put the brakes on hard before my feet had time to hit the brakes it would close the windows and sunroof and put the seats in a more favorite position for an accident it would bring it to a complete stop before hitting anything in front.i am a safe driver and keep a proper distance to cars in front. I have never been in an accident that was my fault. But other people do not drive like that. I have cameras in the front windshield and rear window that constantly record. It will show cars passing me and pulling in front with less than a car length away and my car never responds with any of the safety features.( autonomously braking, seat belts pre tightening etc.) it should do those things faster than humanly possible. The problem with the systems IS that it thinks 20 ft. Is100 feet and 60 ft. IS 200 ft.so it thinks there IS plenty of time to slow down. That IS the way the system IS suppose to detect vehicles in front and to the rear of the car. So the programing that IS controlling the distance IS programed wrong. My 2014 was bought back for that reason and I was given a 2016 replacement. All the 2014 & 2015 & 2016 did not work either.

• Jan 10, 2016ME30 mi
  Unknown or other · Vehicle speed control
  In 2015 mercedes bought back my 2014 S550 due to the reasons stated here.they also helped me buy a 2016 s,which came in around 12/18/2015 figured the problems would have been fixed by then.mercedes had enough time to fix them if they wanted to since I have been complaining since I first got my…

  In 2015 mercedes bought back my 2014 S550 due to the reasons stated here.they also helped me buy a 2016 s,which came in around 12/18/2015 figured the problems would have been fixed by then.mercedes had enough time to fix them if they wanted to since I have been complaining since I first got my 2014.i immediately complained, when my 2016 came in about the same issues as my 2014 head.the distronic plus.you choose the distance you want to keep from the car in front. Once that distance IS set, it does not keep that distance.the car thinks 200 feet IS 90 feet &100 feet IS 40.IT does not recognize a car that pulls in front of you that IS a car length away & does not slow down.if a car moves out from in front of you,the car does not recognize the car that was in front of the other car that left your lane, your car speeds up and does not slow down for that car in front and you have to sharply brake.my car slows down too late all the time and I have to apply the brakes when they should have been applied autonomously & bring the car to a full stop from the car in front maintaining the pre set distance.this happens using it on side roads and on the highway. The autonomous braking suppose to happen at all speeds.my car has the driver assistance pkg.none in that pkg work well, if at all. I had an audi Q7 with the same type of cruise control,i now have a 2015 audi Q7 with it.i have had 2 ford edge's , 2 lexus ls450's after the lexus I purchased a 2007 mercedes S-550 with it .in all those cars it worked exceptionally well. Autonomous braking and pre safe and distronic cruise and all of the driver assistance packages available then were amazing in the 2007 and I felt safe in that car. I do not feel safe at all now. If you have not gotten any other complaints it IS because they do not understand the systems or have the same experience as I do with the safety systems. Or mercedes lied.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10240203This NCU replaces the prior NCU issued on May 11, 2023, and clarifies replacement part information. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, is extending the warranty coverage on the catalytic converter system in certain Model Year (MY) vehicles fitted with the M278 8-cylinder engine listed below: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 13 years / 156,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 144,000 miles (whichever occurs first) - MY2013: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 132,000 miles (whichever occurs first) - MY2014 MY2020: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first)
• 10238430Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2014-2020 S-Class (217 and 222 platform) vehicles, the incorrect pilot bushings may have been installed in the front axle tension struts. It is possible that noises and an increased wear of the pilot bushings may occur. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will check the pilot bushings on the front axle tension struts, and replace if necessary.
• 10233794Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).
• 10233778In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below as follows: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 120,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 120,000 miles (whichever occurs first) - MY2013 MY 2016: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first) This extended warranty applies to the following condition that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinderhead) related to: Over time, increased lateral forces may lead to wear in the valve guide and/or seat ring. This issue could potentially cause combustion misfire for cylinder 1 through 8 (right and/or left cylinder head), resulting in an activation of the check engine Malfunction Indicator Lamp (MIL) .
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
• 10205803The mobile phone address book may not be transferred completely to the multimedia system COMAND, Audio 20, or MBUX. The contact list may not be fully populated and in some instances, the call list will display telephone numbers but no names.
• 10205154Gasket may settle causing a slight oil leak.
• 10202531Touch pad: Search lighting does not dim or does not turn on.
• 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
• 10178714Headlamps fogged
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10135628iPhone mobile phone: Various complaints after software update to iOS8

Every Mercedes-Benz S550 4MATIC model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.