2007 Mercedes Benz S65

Owner complaints

What owners report most

1. Equipment1
2. Exterior lighting1
3. Suspension1
4. Visibility/wiper1

Latest complaints

• Sep 14, 2026MD
  Suspension

  Vehicle erratically adjusts suspension with the left dramatically higher then lower than the right side of the car all while in the middle of traffic. Received message of ABC Chip Malfunction.

• Feb 6, 2016TX
  Exterior lighting · Visibility/wiper
  The wiring harness inside the headlight assembly cracks causing a short, which in turn causes the headlights to stop working. this happened to us during a long distance trip at night. these headlight are not the type of headlights you can pick up at your local auto parts store and can only be…

  The wiring harness inside the headlight assembly cracks causing a short, which in turn causes the headlights to stop working. this happened to us during a long distance trip at night. these headlight are not the type of headlights you can pick up at your local auto parts store and can only be replaced with oem parts. a wire harness IS not currently available and at over $1,900 per light assembly, mercedes benz should be replacing the headlights with the defective wiring. the possibility of these lights going out at night (it happened to us) and causing an accident IS real. I have photos, but the website IS not allowing me to load. the browse button does not do anything...

• Feb 20, 2007GA500 mi
  Equipment

  TL*- the contact owns a 2007 mercedes benz E-350 and stated that the hands free motor function did not work properly. the contact can't receive incoming calls by pressing on the receiver of the steering wheel. the contact took vehicle to the dealer ,and they didn't have a solution for the failure. the current and failure mileage were both 500.*ak updated 03/19/07. *Jb

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10202531Touch pad: Search lighting does not dim or does not turn on.
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10181124Harsh engagement when changing gear range from P to D or R
• 10181123Harsh engagement when changing gear range from P to D
• 101766615 to 4 coasting downshift - shift quality concern with cold trans- mission oil on MODEL 217 or 222 in combination with ENGI- NE 278 and TRANSMISSION 722.9 without code 835/498
• 10167572If it is necessary to replace an HV battery, the return will only be accepted with the filled-out ?Analysis Sheet for Transportability of High-Voltage Batteries Form? accompanied by: , the removed part, the quick test printout, the BMS control unit log printout, the repair documentation and with all required documentation listed in Section E of the Form.
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10167006Engine diagnosis warning lamp active. Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.
• 10166978Engine diagnosis warning lamp lights up - Fault code entry (FC) 14A600 or 14A700
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
• 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
• 10166107Seat belt height adjustment nonfunctional
• 10166106Grinding noises can occur in the backrest on active multicontour seats with the backrest under load and the seat ventilation switched on
• 10166102No inflation of one or more air cushions on the massage/multicontour/dynamic seat modules (driver, front passenger and rear) Bubble formation in one or more seats with massage/multicontour/dynamic seat modules (driver, front passenger and rear)
• 10166100Dynamic seat (DS) pneumatic pump / multicontour seat pneumatic pump makes noises.
• 10166099Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
• 10166098Multicontour system fails during air release procedure. The system becomes operational again after an ignition change. Fault code 9E8900 is stored.
• 10166094Noises from lock of valuables/stowage compartment or from gap cover between seat and center tunnel.
• 10166086Squeaking/creaking noises from area of seat adjuster
• 10166079Creaking noises can occur when the side bolster bladders are inflated and deflated
• 10135628iPhone mobile phone: Various complaints after software update to iOS8
• 10135604Vehicle cannot be opened via Keyless-Go and radio remote control
• 10037986Mercedes benz- when doing a software update the update fails and the tuner goes to boot mode.
• 10037918Mercedes-benz: esp malfunction or bas malfunction light shows up in the instrument panel because of a wheel speed sensor problem. Updated 2/15/13.
• 10037917Mercedes-benze: there IS a leakage at the press-fit sleeve of a pulsation damper. This IS caused by high heat entering the system or tension in the line.
• 10037408Mercedes-benz: shock absorber procedure.
• 10036741Mercedes: mounting bolt of hv connection to hv battery broken during installation. The mounting bolt shears off when retightened at the hv connection to the hv battery. Excessive stress on mounting bolt due to failure to comply with tightening torque of 5NM. Models 221.095/221.195(hybrid). No model years listed.
• 10034609Mercedes: rattling or dull knocking noise coming from the area of the steering system when driving over rough road.
• 10034605Mercedes: seat belts, emergency tensioning retractors. Model series 204 (with codes 299 and 800), 207, 212. Seat belt can only be pulled out with great effort. At the same time a noise can be heard from the reversible reel tensioner gearing. Customer continuously pulled on seat belt strap while adjusting the fit of the belt after buckling up (to reduce the slack). This caused the drive of the reversible reel tensioner to remain engaged. Updated 4/26/12. Updated 5/22/2012.
• 10034151Mercedes: engine start/stop, engine starts up at random or 12 v on board electrical system voltage too low. The resistance of the electrical line from dc/dc converter control unit N83/1 to ground point W3/9 IS too high in the dc/dc converter control unit.
• 10033070Xentry (mercedes): engine warning lamp IS currently on or was on and a delay fault of the camshaft adjust to current or stored in the engine control unit. Models 171, 203, 209, 211, 219, 221, 216, 230, 164, 251, and 403. No model years listed.
• 10032727Mercedes: following fault codes are entered in the control unit and displayed-fc5320 drain valve:open circuit or insufficient valve current in models series 211, 219; fc5260 drain valve open circuit or insufficient valve current in model 221; fc5250 drain open circuit or insufficient valve current in model series 251, 164. Defective connecting cables to drain valve at airmatic compressor. This results in the setting of the fault codes. No model years listed.

Every Mercedes Benz S65 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.