2016 Mercedes-Benz SLK300

Recalls

4 recalls name the 2016 Mercedes-Benz SLK300. Newest first.

• Communication

  Nov 1, 2019NHTSA 19V78700024,226 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…

  Risk and remedy

  Risk

  An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

  Remedy

  MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

  Full recall details →

• Suspension › Rear

  May 16, 2016NHTSA 16V306000327 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 SLK300 vehicles manufactured January 19, 2016 to April 19, 2016. In the affected vehicles, improperly manufactured lock nuts may have been used on the rear wheel tie rod connection, and as a result, the rear wheel alignment may change and the rear axle may steer independently.

  Risk and remedy

  Risk

  A change of the rear wheel alignment and independent steering of the rear axle may increase the risk of a crash.

  Remedy

  MBUSA will notify owners, and dealers will replace the lock nuts on the rear tie rods, free of charge. The recall began on June 24, 2016. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2016050008.

  Full recall details →

• Electrical system › Wiring

  Apr 13, 2016NHTSA 16V211000223 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 SLK300 vehicles manufactured June 2, 2015 to July 14, 2015 and equipped with a nine-speed automatic transmission. The backup power supply for the ignition switch in the affected vehicles may not have been properly connected. As a result, if the vehicle is being driven and there is a loss…

  Risk and remedy

  Risk

  In this situation, without the backup power supply, the only way to keep the vehicle from moving is to press the brake pedal. As soon as the driver attempts to exit the vehicle, the vehicle may roll, increasing the risk of injury.

  Remedy

  MBUSA will notify owners, and dealers will correct the ignition switch wiring and perform a software update, free of charge. The recall began on May 9, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Engine and engine cooling › Engine

  Oct 16, 2015NHTSA 15V662000857 vehicles

  Mercedes-Benz USA, LLC (Mercedes-Benz) is recalling certain model year 2015 CLA250, CLA250 4Matic, GLA250, GLA250 4Matic, and 2016 SLK300 roadster vehicles manufactured July 17, 2015, to August 31, 2015. The affected vehicles have intake or exhaust camshafts whose welds may fail and possibly cause engine damage.

  Risk and remedy

  Risk

  Engine damage may result in a stall, increasing the risk of a crash.

  Remedy

  Mercedes-Benz will notify owners, and dealers will replace the affected camshafts, free of charge. Interim notices were mailed to owners on December 9, 2015. The recall began on December 23, 2015. Owners may contact Mercedes-Benz customer service at 1-800-367-6372. Mercedes-Benz's number for this recall is 2015100006.

  Full recall details →

Owner complaints

What owners report most

1. Unknown or other2
2. Structure1

Latest complaints

• Aug 22, 2025MI
  Structure › Body · Unknown or other
  Sunroof panel detach and let glass panel loose on roadway. I fell that my model should also be part of this classified as 22v-954. However, since it was not on the list so there fore they refused to recognize it as being one of there problem. I believe this IS an over sight with them. I reported…

  Sunroof panel detach and let glass panel loose on roadway. I fell that my model should also be part of this classified as 22v-954. However, since it was not on the list so there fore they refused to recognize it as being one of there problem. I believe this IS an over sight with them. I reported it to them around july 31 2025 to the mercedes care people. They told me that since my car did not have a warranty or an extended warranty and that the car was over nine years old plus with the mileage on the car that this was not there problem. My insurance agent told me that this was a mechaical failure and thata they would not be cover under my policy. However after reading this article they knew that this could happen to any of there model. I'm asking for your assistant to resolve this issue.

• Jan 3, 2021TX25,000 mi
  Unknown or other

  Vapor canister fell of underside of vehicle. part number 171-470-00-59 at high speed this has the potential to be catastrophic as the part IS larger than the underside of the vehicle and could have punctured gas tank if tank IS in rear close to part. fortunately I was backing out of garage and I was able to stop and look. The image of it under car IS with car on an 8 inch block of wood

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
• 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
• 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 11005276Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2018 C300 | Model year 2016-2018 GLC300 and E300 | ALL model year SLK/SLC300 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2018 C300 and 2016-2018 GLC300 and E300 vehicles. Model year 2015-2017 C300 | Model year 2019 GLC300 and E300 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required.
• 11000623Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy Model year 2015-2018 (non-hybrid), and ALL model year 172 and hybrid variants Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for hybrid and model year 2015-2018 vehicles. Model year 2019 (Except model 172 and hybrid variants) Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
• 10253722Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Model year 2015-2018 Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. This LI will be updated once the software solution is available for model year 2015-2018 vehicles. Model year 2019 Perform software update for N3/10 Engine control unit. Replacement of intake line assembly is not required. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
• 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10241531In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the intake line assembly in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended,resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valvemight also increase exhaust gas emission. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has amalfunction. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Code(s): 0101D Solenoid valve, crankcase ventilation system Part(s): A 274 090 5600 80 Intake Line Assembly (inclusive of oil separator, partial load ventilation valve and full-load ventilationvalve.) Where applicable, an ECU software update will be provided for certain vehicle variants. Time Allowed: Intake Line Assembly : 5 hours 40 minutes Software Update: 1 hour Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty.
• 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
• 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
• 10205265Outside mirror fogged.
• 10205248"SOS mbrace service not activated".
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10199787Launch EW NCU - Low Pressure Fuel Hose MY 15-17 205 213 253 172
• 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
• 10178714Headlamps fogged
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10172683Information Label on Tire Sealant
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167557Water entry through front section of retractable hardtop with the following localization: - Partial water entry in the area of the side seals to the A-pillar (for area see Fig. 1) when accelerating/braking the vehicle.
• 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.

Every Mercedes-Benz SLK300 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.