2022 Mercedes-Maybach S 680 4MATIC
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Maybach › S 680 4MATIC › 2022
These records cover every 2022 Mercedes-Maybach S 680 4MATIC. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2022 Mercedes-Maybach S 680 4MATIC. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2025 S 500 4MATIC, Maybach S 580 4MATIC, Maybach S 680 4MATIC, S 580 4MATIC, 2023-2025 S 580 E 4MATIC, and 2024-2025 AMG S 63 E Performance vehicles. The front brake hoses may rupture and leak brake fluid.
Risk and remedy
Risk
A brake fluid leak can extend the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the front brake hoses, free of charge. Owner notification letters are expected to be mailed November 27, 2026. Owners may contact MBUSA customer service at 1-800-367-6372. This recall expands previous NHTSA recall number 25V116. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 9, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 S 500, Maybach S 580 4MATIC, 2021-2023 S 580 4MATIC, 2022 S 680 4MATIC, and 2023 S 580e 4MATIC vehicles. The front brake hoses may rupture and leak brake fluid.
Risk and remedy
Risk
A brake fluid leak can extend the distance needed to stop the vehicle, increasing the risk of a crash.
Remedy
Dealers will replace the front brake hoses, free of charge. Owner notification letters were mailed April 25, 2025. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2025030007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 Maybach S580 and Maybach S680 vehicles. The 12-Volt ground connection in the trunk may not be secured properly, which can impair the electronic stability program (ESP) or result in the ground connection overheating.
Risk and remedy
Risk
Impaired electronic stability control can increase the risk of a crash. An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and repair the 12-Volt ground connection, as necessary, free of charge. Owner notification letters were mailed September 22, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023080008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Owner complaints
1 complaints
What owners report most
Latest complaints
- Electrical system · Service brakes · Steering
While driving a 2022 Mercedes-Maybach S680 at approximately 40 to 65 mph, multiple advanced driver assistance and safety systems suddenly became inoperative at the same time. The vehicle displayed warnings including Active Steering Assist Inoperative, Active Brake Assist Functions Limited, Active…
While driving a 2022 Mercedes-Maybach S680 at approximately 40 to 65 mph, multiple advanced driver assistance and safety systems suddenly became inoperative at the same time. The vehicle displayed warnings including Active Steering Assist Inoperative, Active Brake Assist Functions Limited, Active Distance Assist Inoperative, Blind Spot Assist Inoperative, Lane Change Assist Unavailable, and Emergency Stop Assist Unavailable. These warnings appeared while the vehicle was in motion and reduced steering support, braking assistance, and collision avoidance functionality. The failures occurred without warning and created a safety concern because critical driver assistance systems were disabled during highway driving. The problem has occurred more than once and affects multiple electronic safety systems simultaneously.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010435Complaint -Check engine light(MIL) is ON. -Current and stored fault code in DCCU and PTCU : P2E9873 The position sensor of the exterior socket flap of the vehicle socket (direct current) has an electrical fault. The actuator does not open. -Starting the vehicle or Charging the vehicle is normal without any issues. Cause Software in the "N116/5 - Direct current charge connection unit (DCCU)" control unit. Remedy SW remedy for N116/5(DC-Charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5 For this issue, the vehicle starting or charging functions are not typically affected. Do not replace any parts. Replacing parts will not bring a solution for this issue.
- 11009204Complaint The flush-mounted door handle could jam when it is pulled out and may move in a jerky manner when doing so. In the area of the paneling section of the door, paint damage could be present (picture 1) and/or an abrasion point could be present at the door handle (picture 2). Cause The door handle could be installed too low in the y direction and/or the z direction (picture 3); as a result, the door handle could brush the door at the paneling section of the door. Remedy 1.) Loosen screws from bearing bracket (picture 4, step 1). 2.) Remove bearing bracket (see picture 4, step 2) from door. The door handle must be in pulled-in position. Open the affected door and push the door lock's rotary tumbler into the main catch. Lock the vehicle using the transmitter key so that the door handle is pulled in. Detach plug connector from bearing bracket (center slot). 3.) Paint over paint damage at door paneling (see picture 1) according to manufacturer specifications, using spot repair procedure if necessary. 4.) Loosen old assembly frame (picture 5, step 3). The assembly frame is bonded. Remove adhesive residue at front door. Bonding surfaces must be free of dust, oil, grease, wax, dirt residues and other adhesive components. Otherwise, this can lead to bonding problems. See "Parts" for part number of cleaning agent. 5.) Position new assembly frame (picture 5, step 3) at door. Remove protective film of tape at assembly frame beforehand. The assembly frame (picture 5, step 3) must have the same clearance all around the flange. 6.) Replace door handle, if an abrasion point (picture 2) is present. 7.) Screw in WITOL fasteners (picture 6) completely at mounting points of bearing bracket (picture 7, step 1) and align screws so that they are flush (picture 7, step 2). 8.) Position bearing bracket (picture 4, step 2). The door handle must have the same clearance all around in relation to the paneling section of the door (picture 8). 9.) Press the bearing bracket firmly against the paneling of the door and tighten the screws (picture 4, step 1) (=> torque: 6 Nm). 10.) Check the positioning of the bearing bracket. If necessary, loosen the screws slightly, readjust the bearing bracket slightly, then retighten the screws (=> torque: 6 Nm).
- 11009139Complaint When driving on rough ground, there may be noises from the 4-way head restraint of the front seats. The fault profile is not present at the limit stops (head restraint entirely retracted or entirely extended). Cause Head restraint has increased play between the worm and gearwheel in the head restraint mechanism. Remedy Check play/noise (see video attachment, headrest OK/headrest not OK). Please exchange the head restraint in the event of a not OK result.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009121Complaint Following the software update of the MBUX, the tablet can no longer be connected with the rear seat unit. The tablet cannot be used as usual. Cause The Android software of the tablet is not up to date and cannot communicate with the latest software of the MBUX. Remedy Remedy for Gen1 and Gen2: Update the Android software of the tablet (see instructions in attachment) and head unit A26/17 to the latest version. If the complaint continues to occur after this, please create a TIPS case. Note: Information for Gen1: The tablet's Android software update can be started via the device's system settings (see instructions in attachment). Information for Gen2: To access the device's system settings, the device must be removed from the vehicle and connected to an external Wi-Fi network. (See instructions in attachment).
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11009025Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2018 - 2024 E-Class, S-Class & AMG GT (213, 217, 222, 223 and 290 platforms) vehicles, the low pressure fuel line does not meet current production specifications. Therefore, it is possible that accelerated aging in the area of connection could occur, resulting in a leak. A risk of fire can be ruled out. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will replace the braided hose of low-pressure fuel line and install a heat shield over the new braided hose.
- 11008977Complaint Combustion engine could no longer be started, only electric driving possible. Cause High-voltage belt-driven starter-alternator faulty. Remedy Requirement: Prior to the implementation of the test work, it must be ensured that the person carrying out this work has successfully completed the required HV qualification to work on HV system.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008080Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2024 S-Class and EQS (223 and 297 platform) vehicles, the DRIVE PILOT Supplemental Booklet does not correspond to current production specifications. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the DRIVE PILOT supplemental booklet.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007966Complaint Display dark (total or partial) of one or more ASCM (AMG) steering wheel button displays - see attachment. Note: There is no loss of vehicle functionality due to this complaint. Cause Software can cause a partial display on the ASCM. Remedy Please perform the following steps in the event of a total or partial display of the ASCM displays: 1. Perform a hard reset (disconnect power supply) of control unit A74/2 (ASCM) for 2 minutes. 2. Perform a software update of the A74/2 (ASCM), N145 (DRVU) and A26/17 (HU). 3. Reset the user profile via the head unit settings menu. (Full factory reset)
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 110077311. Connect XENTRY Diagnosis. 2. Update Fuel System Control Unit (FSCU10) software. To do this, select menu item "Quick test view . N118/3 Control unit Fuel pump (FSCU10) . Adaptations . Control unit update . Updating of control unit software". Then follow the user guidance in XENTRY Diagnosis. 3. Disconnect XENTRY Diagnosis.
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006710Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class (206 platform), EQE (294 and 296 platform), EQS (295 and 297 platform), GLC (254 platform), AMG GT (192 platform), S-Class (223 platform), and AMG SL (232 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The communication module will receive an OTA software update that includes product improvements. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers will be mailed a letter informing them of this software update.
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11006699Complaint Radio reception interference and the following DTCs are displayed in the A26/17 - MBUX multimedia system control unit as "active and stored": B19B313 - Antenna 1 open load B19B413 - Antenna 2 open load B19B513 - Antenna 3 open load B19B613 - Antenna 4 open load Cause Antenna amplifier Remedy Replace the antenna amplifier.
- 11006593Complaint The oil level is not correctly displayed while the instrument cluster display is in workshop mode. The oil level is reported in an inverted fashion when a correction is carried out. I.e. instead of an instruction to refill the oil quantity, an instruction to reduce the oil level is displayed, or vice versa. Cause Previous software release for instrument cluster control unit (N133/1) Boot software A2239049101, A2239046801, A2239040802 Remedy Update instrument cluster control unit (N133/1) software using XENTRY Diagnosis
- 11006547Complaint Customer states that wireless Apple Carplay does not initiate at start-up. The MBUX Display states "Apple Carplay could not be started. Your device has been connected as a bluetooth phone" Cause Previous MBUX Multimedia System (A26/17) software Remedy Update the MBUX Multimedia System (A26/17) software to version E330.x or newer.
- 11006545Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% a negative charge balance A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked).
- 11006544Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and /or charging / or parking? If the complaint occurred while charging, how long after did the complaint/IC message occur? Which charging station was used, which provider (picture if possible)? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger
- 11005350Complaint Child seat detected message is shown in the central display and no child seat is installed on the front passenger seat at the time the display message is shown. Cause In certain circumstances, the gesture recognition system may interpret the occupancy status as a child seat present. The following possible conditions may lead to this: 1. Front passenger seat occupied by passenger 2. Object on front passenger seat, e.g. bag or backpack 3. Front passenger seat not occupied The gesture recognition system uses optical imaging to assess the front passenger seat and whether it is occupied and is independent from the occupant classification system input used for airbag deployment. The gesture recognition assessment has no connection to the airbag system. As this is an optical measurement, in certain circumstances a child seat message may be displayed based on the results of the interpretation. There is no influence on airbag system. There is no connection to airbag system. Remedy Software update of control unit N168 - Gesture recognition system OMSH223
- 11005349Complaint Vehicle not AC charging. Check engine light on. PTCU/N127 with fault code P0D9100 "The lock for the charging cable has an open circuit". Cause Possible Hardware and/or Software. Investigation is ongoing. Remedy Please open TIPS case. TIPS case: Needed customer feedback: When did the complaint/IC message occur? While driving and/or charging? If the complaint occurred while charging, how long after did the complaint/IC message occur? Attach HV CUL and QT to the case Attach picture of label of AC charger to the case Attach screenshot of AV AC charger Provide the results of the test below. Test: Verify AC charging Erase fault codes and verify if fault code P0D9100 The lock for the charging cable has an open circuit returns Check AV of AC charger Test with different charging station
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005337Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B129C00 - Malfunction in control unit for telematics services" is active and stored - The head unit shows no internet connection Cause Under analysis. Remedy Please create a TIPS case, attach a RAMSES control unit log to the case.
- 11005336Complaint Digital light pop-up messages (warnings, notes, spotlight and dyn. low beam) appear in the instrument cluster (picture in attachment), even though the same digital light settings are stored in all MBUX profiles Note: The pop-up messages are intended to indicate different settings when changing MBUX profiles Cause - ECU software error Remedy - Reset MBUX to manufacturer default settings. Software update expected to be available YoM24/2 (Year of Modification - Code can be found in VeDoc): - A26/17 - MBUX multimedia system (head unit) -This document will be updated when the software is available.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005315Complaint The oil level is not correctly displayed while the instrument cluster display is in workshop mode. The oil level is reported in an inverted fashion when a correction is carried out. I.e. instead of an instruction to refill the oil quantity, an instruction to reduce the oil level is displayed, or vice versa. Cause Previous software release for instrument cluster control unit (N133/1) Remedy Update instrument cluster control unit (N133/1) software using XENTRY Diagnosis
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
Every Mercedes-Maybach S 680 4MATIC model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.