2010 Mercury Milan
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercury › Milan › 2010
These records cover every 2010 Mercury Milan. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
13 recalls name the 2010 Mercury Milan. Newest first.
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy
Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Ford Motor Company (Ford) is recalling certain air bag inflator and/or module replacement service parts that may have been used as part of a collision repair. The parts include certain driver-side air bag inflators and/or modules, designed to fit 2005-2014 Ford Mustang and Mustang GT500. It also includes certain passenger-side air bag inflators and/or…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Ford will notify dealers that purchased the affected parts, and dealers will provide replacement parts to purchasers, free of charge. The recall began March 18, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Risk and remedy
Risk
If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket that secures the air bag inflator to the module housing may…
Risk and remedy
Risk
If the air bag does not inflate as intended, there is an increased risk of injury in the event of a crash.
Remedy
Ford will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began November 21, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S34.
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not operate properly resulting in abnormal pressure changes in…
Risk and remedy
Risk
The pressure changes may cause the tank to crack and leak fuel. A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Ford will notify owners, and dealers will update the vehicle powertrain control modules and inspect the vehicle for any diagnostic trouble codes (DTCs) for this issue and perform a leak test on the Canister Purge Valve (CPV). The fuel tank will be inspected for cracks. The CPV and fuel tank will be replaced as necessary. These repairs will be performed free of charge. The recall began on January 15, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S34.
Ford Motor Company (Ford) is recalling certain all weather driver side accessory floor mats sold for use in model year 2006-2011 Ford Fusion and Mercury Milan, 2006 Lincoln Zephyr, and 2007-2011 Lincoln MKZ vehicles manufactured November 9, 2007, through October 31, 2010. The affected floor mats may move and possibly interfere with the accelerator pedal.
Risk and remedy
Risk
The floor mat could shift such that it could interfere with the accelerator pedal, preventing its return to an idle position, which could result in unintended vehicle speeds, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will install new replacement mats, free of charge. The recall began in July 2014. Owners may contact Ford's customer service at 1-800-392-3673. Ford's number for this recall is 14S07. NOTE: Vehicles built after October 31, 2010, while potentially equipped with the same floor mats, are equipped with a Brake Over Accelerator (BOA) feature that prevents simultaneous accelerator and brake application, allowing the vehicle to be safely stopped by pressing firmly and steadily on the brake pedal.
Ford IS recalling certain model year 2010-2011 ford fusion and mercury milan vehicles equipped with 17 inch steel wheels and built from april 1, 2009, through april 30, 2009, and from december 1, 2009, through november 13, 2010. the wheel studs may fracture, potentially causing a wheel to separate.
Risk and remedy
Risk
While driving, multiple stud fractures could occur at the wheel location, and the operator may experience vehicle vibration and/or wheel separation, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will inspect the rear brake disc surface for flatness and replace the discs as necessary. Additionally, the wheel lug nuts will be replaced on all four wheels. the safety recall IS expected to begin on or about january 24, 2012. owners may contact the ford motor company customer relationship center at 1-866-436-7332.
Ford IS recalling certain model year 2010 fusion, milan, and escape vehicles manufactured from february 27, through march 26, 2010. the park rod guide retention pin may not have been properly installed which fails to conform to the requirement of federal motor vehicle safety standard no. 114, "theft protection and rollaway prevention".
Risk and remedy
Risk
A vehicle parked without an engaged park pawl and without an applied parking brake may have unintended movement which may cause a crash.
Remedy
Ford will notify owners and dealers will repair the vehicles free of charge. the safety recall began on may 28, 2010. owners may contact ford motor company customer relationship center at 1-866-436-7332 and for the hearing impaired call 1-800-232-5952 (tdd). representatives are available monday through friday: 8:00am - 5:00pm.
Ford IS recalling certain model year 2010 fusion, explorer, explorer sport trac, and mercury milan and mountaineer vehicles manufactured between december 15, 2009 through february 3, 2010 equipped with front seat manual recliners. these vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 202, "head restraint." the…
Risk and remedy
Risk
In the event of a crash, the seatback and head restraint may move rearward, increasing the risk of injury.
Remedy
Dealers will replace the manual recliners for both power and manual seats free of charge. the safety recall IS expected to begin on or before april 30, 2010. owners may contact ford at 1-866-436-7332.
Owner complaints
1,003 complaints40 involved a crash1 involved a fire22 injuries
What owners report most
Latest complaints
- Electrical system · Power train · Steering
While driving my 2010 Mercury Milan, the steering suddenly went out, making the vehicle extremely difficult to control. I almost hit another car because I could not steer properly. This was a serious safety concern, and I believe the steering issue needs to be investigated immediately.
- Air bags
The contact owned a 2010 Mercury Milan. The contact stated that while driving at an undisclosed speed, the vehicle was involved in a crash. The contact stated that the vehicle flipped over and landed on its roof of the vehicle. The air bags did not deploy. The vehicle was towed to a local tow yard.…
The contact owned a 2010 Mercury Milan. The contact stated that while driving at an undisclosed speed, the vehicle was involved in a crash. The contact stated that the vehicle flipped over and landed on its roof of the vehicle. The air bags did not deploy. The vehicle was towed to a local tow yard. The contact was later taken to the local medical center. The contact sustained pain and bruises to the chest area, the left and right knees from the impact of the steering wheel, the middle back, and the left side hip. A Police report was filed. The vehicle was deemed a total loss by the insurance company. In addition, the contact stated that an unknown recall for the air bag was completed in 2025. The manufacturer was not made aware of the failure. The failure mileage was approximately 160,000.
- Steering
While driving at low speed performing a turn in a residential area, the vehicle suddenly displayed a “Steering Assist Fault” warning message and the steering wheel became completely locked with essentially no movement possible. I attempted to turn the wheel with extreme force but it would barely…
While driving at low speed performing a turn in a residential area, the vehicle suddenly displayed a “Steering Assist Fault” warning message and the steering wheel became completely locked with essentially no movement possible. I attempted to turn the wheel with extreme force but it would barely move, creating a serious safety hazard. I was fortunately driving slowly at the time. If this had occurred at higher speed or in traffic, it could have caused a crash, serious injury, or even death. Prior to the incident, there had occasionally been a slight amount of unusual tension/resistance felt while turning the steering wheel, although it was minor and inconsistent before the complete failure occurred. The failure happened suddenly while driving normally. The issue appears related to the electronic power steering (EPAS) / steering assist system. Similar steering assist failure complaints and recalls/investigations have existed on related Ford Fusion/Mercury Milan vehicles involving sudden loss of steering assist and steering control concerns. The vehicle is also currently affected by brake recall 19S54/19V904 involving braking performance concerns, increasing overall safety concerns regarding the vehicle. At the time of filing this complaint, the steering issue has not yet received a complete repair or confirmed diagnosis because the manufacturer and dealer stated the VIN is not currently included under steering recall coverage.
- Electrical system · Steering
I was driving on the freeway and the steering began to stiffen. I got to my destination and decided to check the tires for any ice or snow, thinking that might be why it was difficult to drive but there was no buildup. I made it home and parked the car. The next day, I can't even turn the steering and a warning comes up that says service power steering and advancetrac.
- Steering
Bought this car less then a year ago with 38k miles and just last week after coming back from vacation my power steering system went while on the expressway. The advancetrac warning light came on and then the service power steering now. The steering wheel was impossible to turn and to make matters worse it was snowing out.
- Electrical system · Steering
The electric power steering has failed again this will make it twice in 18 months the last time it cost 1800 dollars to fix it know that only some of the 2010 Mercury Milans are on a recall list unfortunately mine is not on that list why because it is absurd that I should I have to make this repair for 1800 dollars again you cant safely drive this car it takes everything I have to turn the steering wheel
- Service brakes
The safety recall 19S54 is affecting my vehicle. It was made at the same plant at the approved date range as the other vehicles on the recall list but it seems my vehicle wasnt added to the list because it is a hybrid but it has the same exact issue as the non hybrid models
- Steering
The contact owns a 2010 Mercury Milan. The contact stated that while driving approximately 30 MPH, the "Service Traction Control" and “Power Steering Sensor” warning lights illuminated. The contact stated that the steering wheel became difficult to turn to the left or the right. The contact was…
The contact owns a 2010 Mercury Milan. The contact stated that while driving approximately 30 MPH, the "Service Traction Control" and “Power Steering Sensor” warning lights illuminated. The contact stated that the steering wheel became difficult to turn to the left or the right. The contact was able to drive the vehicle back to the residence. The local dealer was contacted and sent an agent to the residence to drive the vehicle to the dealer. The vehicle was diagnosed, and it was determined that the power steering assist had failed, and the steering gears and rack, and pinion needed to be replaced. The vehicle was repaired. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was 60,562.
- Air bags · Fuel/propulsion system
I collided with three parked vehicles and my airbags did not deploy causing me to hit my head
- Service brakes, hydraulic
The contact owns a 2010 Mercury Milan. The contact stated that while depressing the brake pedal to the floorboard, the vehicle failed to immediately stop. The vehicle was taken to the local brake service center, but the cause of the failure was not yet determined, and the vehicle was not yet…
The contact owns a 2010 Mercury Milan. The contact stated that while depressing the brake pedal to the floorboard, the vehicle failed to immediately stop. The vehicle was taken to the local brake service center, but the cause of the failure was not yet determined, and the vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 19V904000 (SERVICE BRAKES, HYDRAULIC). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was approximately 140,000.
- Fuel/propulsion system · Steering · Suspension
Check engine light is on mechanic says it's a fuel tank issue
- Steering
I experienced a loss of power steering while driving and a dash display "Service Power Steering Now" and "Service Advancetrac". The messages started just before the failure. The lack of power steering was a risk to everyone as the car could only be turned with significant effort and not respond to…
I experienced a loss of power steering while driving and a dash display "Service Power Steering Now" and "Service Advancetrac". The messages started just before the failure. The lack of power steering was a risk to everyone as the car could only be turned with significant effort and not respond to quick movement. The dash messages are still on after a restart and the car cannot be driven because of safety. My independent mechanic confirmed the issue and fix to be a bad rack. He noted the rack part number is the same as the 2011 Milan, currently under recall for this issue. However, the 2010 is not included.
- Service brakes
Whenever the car engine isn't warm and I slam on the brakes, they barely respond. I have replaced the master cylinder, abs hydraulic module, brake booster, calipers, pads, and rotors, and it still has about 20% normal braking power when the engine is cold. Just got it back from the dealership…
Whenever the car engine isn't warm and I slam on the brakes, they barely respond. I have replaced the master cylinder, abs hydraulic module, brake booster, calipers, pads, and rotors, and it still has about 20% normal braking power when the engine is cold. Just got it back from the dealership again. Dealer said no vacuum leak found, no leaks found, abs module checks out fine, and said the check valve passed diagnostics. The problem remains. This has been ongoing for several years now. May have contributed to an accident in 2023. Not sure as my wife was driving. When the engine is warm, the brakes work perfectly.
- Steering
The contact owns a 2010 Mercury Milan. The contact stated while driving at various speeds, the steering wheel was difficult to turn. Additionally, the contact stated while driving 30-35 MPH, the steering wheel seized inadvertently. There were no warning lights illuminated. The contacted depressed…
The contact owns a 2010 Mercury Milan. The contact stated while driving at various speeds, the steering wheel was difficult to turn. Additionally, the contact stated while driving 30-35 MPH, the steering wheel seized inadvertently. There were no warning lights illuminated. The contacted depressed the brake pedal and pulled over to the side of the road and parked the vehicle. The contact stated that upon returning to the vehicle, the vehicle was restarted, and the steering wheel was no longer seized, but the steering wheel was difficult to turn. The contact was able to drive the vehicle; however, the failure recurred while driving. The dealer was notified of the failure and informed the contact that the failure was related to NHTSA Campaign Number: 15V340000 (Steering); however, the VIN was not included. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Steering
The contact owns a 2010 Mercury Milan. The contact stated while driving at approximately 45 MPH while turning the steering wheel to the right, the steering warning illuminated, and the steering wheel became difficult to turn. The contact stopped and turned off the vehicle and the power steering…
The contact owns a 2010 Mercury Milan. The contact stated while driving at approximately 45 MPH while turning the steering wheel to the right, the steering warning illuminated, and the steering wheel became difficult to turn. The contact stopped and turned off the vehicle and the power steering function returned. The contact had not taken the vehicle to a local dealer or independent mechanic. The vehicle was not diagnosed or repaired. The contact researched online and related the failure to NHTSA Campaign Number: 15V340000 (Steering). The manufacturer was informed of the failure. The failure mileage was approximately 126,000.
- Service brakes, hydraulic
The contact owns a 2010 Mercury Milan. The contact stated that while operating the vehicle, the "Check Brake System" and "Service Advance Track" messages remained displayed. The cause of the failure was not yet determined. The contact indicated that the failure had occurred days after the vehicle…
The contact owns a 2010 Mercury Milan. The contact stated that while operating the vehicle, the "Check Brake System" and "Service Advance Track" messages remained displayed. The cause of the failure was not yet determined. The contact indicated that the failure had occurred days after the vehicle was repaired under NHTSA Campaign Number: 19V904000 (SERVICE BRAKES, HYDRAULIC). The manufacturer and local dealer were notified of the failure. The failure mileage was 240,000.
- Steering
started vehicle, "power steering assist fault" message appeared on dash message center, unable to turn steering wheel. Turn car off, waited, turn back on, message appeared again. tried an additional 3 times, same results. Had to leave the car where i was visiting.
- Steering
My power steering light came on and then immediately the wheel got tight. I was unable to turn the wheel and then eventually the car is un drivable. There is a lot of complaints about this happening to thousands of cars and it is still under investigation. Imagin someone jumps out in front of you…
My power steering light came on and then immediately the wheel got tight. I was unable to turn the wheel and then eventually the car is un drivable. There is a lot of complaints about this happening to thousands of cars and it is still under investigation. Imagin someone jumps out in front of you and you are stopping and unable to maneuver your car out of the way. By the grace of God I was able to do so. Please advise me when this recall is open.
- Steering
The contact owns a 2010 Mercury Milan. The contact stated that the power steering assist became inoperable. The driver was unable to turn the steering wheel. The contact stated that the steering wheel had seized. The vehicle was restarted, and the steering wheel operated as designed. The power…
The contact owns a 2010 Mercury Milan. The contact stated that the power steering assist became inoperable. The driver was unable to turn the steering wheel. The contact stated that the steering wheel had seized. The vehicle was restarted, and the steering wheel operated as designed. The power steering assist fault and service power steering soon messages were displayed. The contact stated that the failure was related to NHTSA Campaign Number: 15V340000 (Steering). The local dealer was contacted, and the contact was referred to the Ford Warranty Department for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 38,000.
- Engine
The contact owns a 2010 Mercury Milan. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the electronic throttle body and the throttle body injectors failed and…
The contact owns a 2010 Mercury Milan. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic where it was diagnosed that the electronic throttle body and the throttle body injectors failed and needed to be replaced. The vehicle was not repaired. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 153,000.
- Steering
See attached document for complaint
- Service brakes
My name is [XXX] and I own a 2010 Mercury Milan. I bought it on [XXX] from an 84 year old woman who take good care of it. It had 91,000 miles which were mostly hwy miles. She kept records of all her oil changes. After having it for almost 3 years and keeping up with it myself, on February 27,2024…
My name is [XXX] and I own a 2010 Mercury Milan. I bought it on [XXX] from an 84 year old woman who take good care of it. It had 91,000 miles which were mostly hwy miles. She kept records of all her oil changes. After having it for almost 3 years and keeping up with it myself, on February 27,2024 in the morning I put brake fluid in the car. I had brake pads and rotors done on the car in August 2023. On the evening of [XXX], my son and I took a ride to the local 7/11 which is 5 minutes away. While driving home and coming to the traffic light at the beginning of my neighborhood the light turned red. As I proceeded to stop my foot went all the way to the ground and I had no brakes. I had to go through the light because i could not stop. The car was flying down the road because it is a very steep hill. I tried to pull the emergency brake and nothing happened. I was nearing the end of the road going 40 MPH due to the hill. I thought I was going to hit my neighbors house at the bottom of the hill. My son grabbed the steering wheel to turn it and I went up on my curb, across my lawn and crashed into a storage tent on my driveway. My car was wedged inside the tent which was filled with furniture and other belongings. I called Ford Corporation in reference to this recall from December 2019 for 2010 Mercury Milans. Then I spoke with a Ford dealership in Smithtown where they were rude and said the car was 14 years old and I may have to pay if they didn't find my car was part of the recall. I tried calling several other numbers in Washington and was finally told to upload the horrible situation that had occurred due to my brakes not working on this website. Someone needs to look at my car to make sure this will not happen to others. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Steering
Upon starting the vehicle, the steering wheel is firm and very difficult to manouver. It requires a great amount of strenght to just turn. The vehicle was diagnosed by the dealer and by a mechanic and both said there was a problem with the steering wheel.
- Steering
After turning the car on one morning, an alert displayed on the dash saying "Power Steering Assist Fault" and "Service Advancetrac". I turned the car off, and back on, but the same message appeared. When driving, there is no power steering and it is difficult to turn the steering wheel. The Milan only has 110,000 miles. Ford needs to issue a recall as this is obviously a defect affecting many customers.
- Steering
The contact owns a 2010 Mercury Milan. The contact stated that upon starting the vehicle, the steering wheel was firm and difficult to maneuver. The contact stated that an unknown warning light was illuminated. The vehicle was taken to a dealer, where it was diagnosed and determined that the…
The contact owns a 2010 Mercury Milan. The contact stated that upon starting the vehicle, the steering wheel was firm and difficult to maneuver. The contact stated that an unknown warning light was illuminated. The vehicle was taken to a dealer, where it was diagnosed and determined that the steering rack needed to be replaced. The vehicle was repaired. The contact related the failure to NHTSA Campaign Number: 15V340000 (Steering). The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 69,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Electronic Throttle Body Malfunction
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this…
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
- Floor mat interference with accelerator
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at…
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
- Wheel Mounting Stud Fracture
To date, the agency is aware of 84 consumer complaints and 361 warranty claims related to the alleged defect in the subject vehicles.In total, 382 subject vehicles reportedly experienced one or more wheel stud fractures, resulting in 7 alleged wheel separation incidents.Most of the reported wheel stud fractures…
To date, the agency is aware of 84 consumer complaints and 361 warranty claims related to the alleged defect in the subject vehicles.In total, 382 subject vehicles reportedly experienced one or more wheel stud fractures, resulting in 7 alleged wheel separation incidents.Most of the reported wheel stud fractures occurred on subject vehicles originally equipped with 17 inch diameter steel wheels (368 of 382) as did all 7 alleged wheel separation incidents.Of the 7 alleged wheel separation incidents, 5 reportedly involved a wheel becoming detached from the subject vehicle's rear axle.The subject vehicles are designed with a safety margin that requires validation of proper wheel joint function with one missing lug nut and all other lug nuts at the minimum torque specification.If multiple stud fractures occur at a wheel location, analysis of reports indicates that the operator may observe vehicle vibration. If the vibration is ignored and the vehicle continues to be driven the remaining studs may fracture, resulting in a wheel separation.By letter dated December 5, 2011, the manufacturer notified the agency that it will conduct a safety recall (identified by NHTSA Recall No.11V-574 and Ford Recall No. 11S23) on certain 2010 and 2011 model year Ford Fusion and Mercury Milan vehicles to address the potential for wheel separation.The recall vehicles were originally equipped with 17 inch diameter steel wheels and were built from April 1, 2009, through April 30, 2009, and from December 1, 2009, through November 13, 2010.Approximately 128,616 vehicles are potentially affected as well as approximately 2,940 service steel wheels distributed to authorized Ford dealers.Ford has identified two distinct root causes of wheel stud fracture in the recall vehicles.First, certain steel wheel centers may have been stamped improperly such that the mounting pad lacks the necessary concavity, which reduces the diameter of the outermost radial points of contact with the brake rotor.This reduces the Belleville washer effect, which reduces the clamp load of the joint.Second, the wheel mounting face on certain rear brake discs may have been machined improperly due to a damaged dust boot on a gauge that measures rear brake rotor parallelism (flatness), resulting in a wheel mounting face that is convex.One or both conditions may induce bending fatigue in the wheel studs.Ford's analysis of manufacturing process information showed that one or both of these two conditions may have been out of control during parts of one or both production ranges covered by the recall.Owners will be notified by mail and instructed to take their vehicles to an authorized Ford or Lincoln dealer to have the lug nuts replaced on all four wheels with new lug nuts treated with a proprietary low-friction coating that improves clamp load given the same applied torque value, and to have the rear brake discs inspected for wheel mounting surface flatness and replaced, if required.Ford will instruct dealers to notify customers who purchased service steel wheels, where information is available, to return vehicles for lug nut replacement.Accordingly, this investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10364337, 10373257, 10378953, 10381431, 10389641, 10389940, 10392373, 10395676, 10396577, 10400071, 10402309, 10416653, 10419175, 10419734, 10420116, 10424191, 10432393, 10434188, 10436471, 10438725 and 10440830.
- Wheel Stud Fracture
On January 21, 2011, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE11-003) to investigate alleged wheel stud fractures in certain model year (MY) 2010 Ford Fusion vehicles.ODI sent the manufacturer an information request letter dated February 8, 2011 and Ford responded by letter dated…
On January 21, 2011, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE11-003) to investigate alleged wheel stud fractures in certain model year (MY) 2010 Ford Fusion vehicles.ODI sent the manufacturer an information request letter dated February 8, 2011 and Ford responded by letter dated March 25, 2011.Ford provided a supplemental response by letter dated July 15, 2011.To date, ODI is aware of 29 complaints related to the alleged defect in the subject vehicles, which now include certain MY2010 Mercury Milan vehicles that are the same or substantially similar to the subject Ford Fusion vehicles in regards to the alleged defect.In total, ODI is aware of 4 reported wheel separation incidents related to the alleged defect in the subject vehicles.The manufacturer's investigation into the root cause of the alleged defect is ongoing.Accordingly, this investigation has been upgraded to an Engineering Analysis (EA11-009) to further study the alleged defect.
- Fleet Vehicle Recall Completion Audit
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary…
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
- Accel Pedal Interference - Acc Floormat
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show…
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10250305When performing any transmission fluid change or topoff involving Motorcraft Premium ATF, MERCON V has replaced all versions of Motorcraft Premium ATF and can be used going forward. Mixing Motorcraft Premium ATF and MERCON V in the same transmission is acceptable. After 31-Jan-2024, Motorcraft Premium ATF will no longer be manufactured and will only be available until inventory depletes.
- 10240415Certain 2005-2014 Mustang, 2005-2006 GT, 2004-2011 Ranger, 2006-2012 Fusion and MKZ/Zephyr, 2006-2011 Milan, and 2007-2010 Edge & MKX Vehicles Driver & Passenger Airbag Module Quality Control Inspection REASON FOR THIS SUPPLEMENT Updated Ranger Technical Information to include images of a pass and fail airbag inflator inspection for 2007-2011 model years.
- 10236689Some 2010-2012 Fusion/Milan and 2011-2012 MKZ vehicles equipped with a 2.5L or 3.0L engine and electronic power assist steering (EPAS), a remanufactured replacement steering gear (MU2Z-3V504-ARM) is available which is significantly less expensive than a new replacement gear. When conducting repairs that are customer pay, offer the customer a remanufactured gear when possible. This would include vehicles not included in field service action (FSA) 15N01 (built on or before 7-Sep-2010) or vehicles included in FSA 15N01 that have exceeded the 10 year/150,000 mile terms of the program.
- 10234103Some 2010-2012 Fusion hybrid electric vehicles (HEV), 2010-2011 Milan HEV and 2011-2012 MKZ HEV vehicles may experience reduced electric vehicle operation and increased gasoline engine operation around 10 years of vehicle age and beyond. This may be due to software in the battery energy control module (BECM) and the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the BECM and PCM.
- 10209374Certain 2005-2014 Mustang, 2005-2006 GT, 2004-2011 Ranger, 2006-2012 Fusion & MKZ/Zephyr, 2006-2011 Milan, and 2007-2010 Edge & MKX Vehicles Driver & Passenger Airbag Module Quality Control Inspection: Ford Motor Company has determined that some vehicles claimed by dealers as repaired under Takata Airbag Safety Recalls 15S21, 17S42, 18S02, 19S01, and 21S12 may not have received the claimed repairs. The propellant in certain Takata airbag inflators can experience an alteration over time with exposure to certain climate conditions. A combination of time, high temperature fluctuations, and humidity contribute to the degradation of the propellant in the inflators. This degradation can cause the propellant to burn too quickly, creating high pressure inside the inflator, and in extreme cases causing the inflator to rupture in the event of a crash necessitating airbag deployment. A ruptured inflator can send inflator parts toward vehicle occupants resulting in serious injury or death. Additional information regarding Takata recalls can be found at www.nhtsa.gov and www.safercar.gov.
- 10205727Certain 2006-2010 Model Year Fusion/Milan/MKZ/Zephyr Vehicles Equipped with Anti-Lock Brake Systems DOT 3 Brake Fluid and Anti-Lock Brake System Function In some of the affected vehicles, customers may return to the dealer with complaints of extended brake pedal travel after either 19S54 or 20S14 was previously performed and the program is closed
- 102050086F35 Transmission - Fluid leak at left side halfshaft seal - built on or before 10/14/2013
- 10164508Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
- 10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
- 10140323The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
- 10137113Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
- 101365972010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
- 10109070The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
- 10095995Some 2010-2016 epas equipped vehicles may exhibit steering related noises. The workshop manual (wsm) diagnostic procedures have been updated in section 211-02. When diagnosing and repairing epas steering noises use the updated procedures.
- 10095184Replacing the original equipment sync/navigation system with either an aftermarket sync/navigation kit or modifying original sync/navigation parts to provide additional features IS not recommended nor supported on any ford, mercury or lincoln vehicle. Only approved genuine ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: monroney label (window sticker), professional technician society (pts) oasis tab select sync or hvbom. For genuine ford accessories use: pts workshop tab select dealer installed accessory or accessory installation.
- 10091151Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service IS required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps illuminated in the instrument cluster. Rerun the vhr with the engine on and vehicle in park, and ensure the park brake IS disengaged. If the sync vhr IS still reporting a concern to the customers sync owners account, refer to the appropriate workshop manual section for diagnosis by dtc or symptom. Starting in 2015 not all sync equipped vehicles support vhr, refer to the owners manual for vhr operation.
- 10090681Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service IS required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps illuminated in the instrument cluster. Rerun the vhr with the engine on and vehicle in park, and ensure the park brake IS disengaged. If the sync vhr IS still reporting a concern to the customers sync owners account, refer to the appropriate workshop manual section for diagnosis by dtc or symptom. Starting in 2015 not all sync equipped vehicles support vhr, refer to the owners manual for vhr operation.
- 10090508Some 2010-2012 fusion hybrid, milan hybrid and MKZ hybrid vehicles may exhibit an illuminated malfunction indicator lamp (mil) with diagnostic trouble codes (dtcs) p0030 and/or p0130. Follow the service procedure steps to correct the condition.
- 100752736F35 TRANSMISSION - FLUID LEAK AT LEFT SIDE HALFSHAFT SEAL BUILT ON OR BEFORE 10/14/2013 ISSUE Some 2009-2014 Escape, 2009-2011 Mariner, 2010-2014 Fusion, 2010-2011 Milan, 2012-2014 Edge/Explorer, and 2013-2014 Taurus/MKT/MKZ vehicles built on or before 10/14/2013 and equipped with a 6F35 automatic transmission may exhibit a fluid leak from the left hand (LH) transmission halfshaft seal due to wear on the transmission case bushing.
- 10058463Lincoln/ford: some vehicles will experience, in hot extreme ambient temperatures, a stop safely now or a malfunction indicator lamp (mil) illuminated in present of battery energy control module (becm) dtc p0a7e and becm needs replaced, and reprogram. Model 2010-12 fusion, milan, MKZ.
- 10057876Ford 2010-2011 milan and MKZ vehicles: customer satisfaction program regarding tail lamp assembly extended coverage to 10 years or 150,000 miles warranty.
- 10057873Ford fusion, milan, escape, mariner 2009-2013: customer satisfaction program throttle body extended coverage.
- 10057860Ford: in valve body, a worn solenoid pressure regulator valve has diagnostic trouble code (dtc) p0735 stored and indication of repair history was the valve body was not replaced previously. Model 2009-10 escape, mariner, 2010 fusion, milan.
- 10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
- 10056183Ford: the throttle body internal motor contacts may be contaminated, resulting in an electrical, intermittent, connectivity, causing malfunction indicator lamp (mil) or wrench light to be illuminated. Model 2009-2012 fusion, milan, escape, mariner. Updated 11/18/14.
- 10055321Mercury/ford: on some vehicles, there IS a fluid leakage, coming from left hand (lh) halfshaft seal of the automatic transmission and a service kit IS available now, for repair. Model 2009-2012 escape, mariner, fusion, milan.
- 10054926Ford: throttle body will develop contamination on internal motor contacts resulting in an intermittent electrical connectivity and malfunction indicator lamp (mil) or wrench light will illuminate. Model 2009-2013 fusion, milan, escape, mariner. Updated 5/7/14.
- 10054575Ford: on the left hand half shaft seal, there IS a fluid leak from the transmission because of wear on case bushing. Model 2009-2012 escape, 2009-2011 mariner, 2010-2012 fusion, 2010-2011 milan.
- 10053656Ford: due to an intermittent loss of rpm or lack of acceleration, in some vehicles, with illuminated wrench light, diagnostic trouble codes (dtcs) p2111, p2112 may or may not be stored in powertrain control module (pcm). Models 2009-12 escape, mariner, fusion, milan.
- 10052191Ford/lincoln/mercury: some vehicles may experience an illuminated mil or safety stop now message, or a no start condition or possible misfire or roughness at idling through 2000rpm or a lack of acceleration. Models 2009-12 escape, 2009-11 mariner, milan, 2010-12 fusion, 2011-14 mustangs, 2013 c-max, fusion, MKZ hybrid.
- 10043648Ford: the variable camshaft timing vct) solenoid movement may be temporarily restricted due to debris in engine oil that IS causing diagnostic trouble codes (dtcs).
- 10043325Ford/mercury/lincoln: some model year vehicles may exhibit a message with a red triangle on and stop safely now, and/or have a diagnostic trouble code, no start condition.
- 10042506Mercury/lincoln/ford: the red brake lamp will illuminate with no change in brake pedal feel.
- 10040948Ford: there may be a leaking/stuck canister purge valve which can cause multiple driving systems. The malfunction light may be on with or without stored trouble codes.
- 10039156Ford: the chrome may peel or wrinkle on the chrome handles. This IS caused by the curing process of the finish. 2010 fusion/milan/mks.
- 10039151Ford: there may be loose molding in the base of the rear window glass. 2010 fusion/milan/mkz.
- 10039111Ford: there may be a steering drift while driving on a flat or uneven road surface. 2010-2011 fusion/milan/mkz. This could be normal.
- 10039081Ford: engine power may be reduced with a high idle speed. The engine light may also be on with a stored trouble code. Programming issue. 2010-2011 fusion/merucry milan/lincoln MKZ.
Every Mercury Milan model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.