1992 Nissan Stanza
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Stanza › 1992
These records cover every 1992 Nissan Stanza. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 1992 Nissan Stanza. Newest first.
It IS possible for a mixture of mud and salt to get trapped between the fuel filler tube and wheel housing. The trapped mud and salt can result in corrosion of the fuel filler tube and the wheel housing.
Risk and remedy
Risk
Significant corrosion of the fuel filler tube may result in fuel leaks which in the presence of an ignition source could result in a fire. In addition, the left rear seat belt retractor IS mounted to the wheel housing and in the event of significant corrosion, and the mounting could fail in a vehicle crash.
Remedy
Dealers will inspect these vehicles and corrective action will be taken depending upon the extent of the corrosion.
Owner complaints
33 complaints2 involved a crash2 involved a fire2 injuries
What owners report most
Latest complaints
- Structure › Body › Trunk lid
Dt: consumer reports: the trunk of her car falls down on her head. There isn't anything there to secure it; when the wind blows or if she IS putting something in the trunk, it will fall down . *jb
- Seat belts
Front driver's seat automatic seatbelt will not retract into locking position, causing consumer not to have a seatbelt on while driving. Dealer notified.*ak
- Fuel system, gasoline › Fuel injection system › Injectors
Consumer could smell something burning. Consumer was purchasing more gas, but not getting mileage. Took to dealer ,and they said it was fuel injectors. They were leaking gas on engine.*ak
- Engine and engine cooling › Engine › Gasoline
With no warning, the timing chain skipped sprockets on startup, causing valve, cylinder, and crankshaft damage. This neccessitated replacement of the engine at a total cost of $3902.21. Nissan would do nothing about reimbursing any of the expense due to a tensioner design defect, since the auto was…
With no warning, the timing chain skipped sprockets on startup, causing valve, cylinder, and crankshaft damage. This neccessitated replacement of the engine at a total cost of $3902.21. Nissan would do nothing about reimbursing any of the expense due to a tensioner design defect, since the auto was out of warrantee. Since internal timing chains usually last the useful life of an engine, about 120-140k miles, this was very premature. While, the incident happened while the auto was stationary, it could very well have happened on a highway while traveling at 70 mph. The engine would possibly seize, with an instant deceleration with a manual shift car.
- Tires
Tread separations on three out of four tires (tiresize: 195-65r14)( dot number: tire size: 195-65r14 )
- Engine and engine cooling › Engine · Fuel system, gasoline › Fuel injection system › Injectors
Vehicle brought to star nissan for 9/29/00 inspection of gas smell. Mr. John choe gave written repair estimate. Informed by mr. Choe that gas leak was dangerous, and all (4) injectors and seals must be replaced at owner's expense. Same for rear engine mount. *ak
- Fuel system, gasoline › Fuel injection system
Fuel poured out of vehicle due to fuel injection system failure. this could cause a fire. *ak
- Power train › Automatic transmission › Cooling unit and lines · Steering › Hydraulic power assist system
When driving vehicle would vibrate and a slight rubbing sound was heard. contacted dealer, and didn't see anything wrong. slight leak in the transmission airlines and zero ring distributor. Also, rear brake adjustment and bushing. power steering unit shifted the belt was coming off and pump was angled. contacted another dealer, and waiting for a call back. *Ak
- Fuel system, gasoline › Fuel injection system › Injectors
While driving the smell of gas IS noticed throughout the inside of the car. took it in to have it checked out and was told that the 2 fuel injectors are leaking, and that nissan has been having problems with its fuel injectors in the stanza and maxima models. I do not see a recall for this…
While driving the smell of gas IS noticed throughout the inside of the car. took it in to have it checked out and was told that the 2 fuel injectors are leaking, and that nissan has been having problems with its fuel injectors in the stanza and maxima models. I do not see a recall for this problem, but seems like it's an ongoing problem for nissan. this IS an expensive problem to fix and if not fixed renders the car dangerous and fire-prone. *ak
- Power train › Automatic transmission › Cooling unit and lines · Steering › Hydraulic power assist › Pump · Suspension › Front
When driving vehicle would vibrate and a slight rubbing sound was heard. contacted dealer, and he didn't see anything wrong. slight leak in the transmission airlines, and zero ring distributor. power steering unit shifted and the belt were coming off and pump IS angled. contacted another dealer and waiting for a call back. *Ak
- Suspension
Vehicle will vibrate at various of speeds which could cause loss of steering and control. *ak
- Fuel system, gasoline › Fuel injection system › Injectors
Fuel injector failed, causing a fuel leak. *ak
- Fuel system, gasoline › Fuel injection system
2 fuel injectors leaking gas onto engine. I have checked and there are at least 30 similar complaints on 1990 - 1992 nissan stanzas. what does it take to initiate a recal. several of these have resulted in fires. the dealer would not tell me if any other models use the same injector, or I would…
2 fuel injectors leaking gas onto engine. I have checked and there are at least 30 similar complaints on 1990 - 1992 nissan stanzas. what does it take to initiate a recal. several of these have resulted in fires. the dealer would not tell me if any other models use the same injector, or I would have checked them as well. this IS a very volitile safety issue with gasoline leaking on a hot engine. I think something should be done.
- Fuel system, gasoline › Fuel injection system › Injectors
Fuel injectors were leaking gasoline onto the engine. The problem was reported to the dealership. The fuel injectors have been replaced at owner's cost. Please provide any further information. *ak
- Engine and engine cooling › Engine
Engine head gasket blew out while driving, causing vehicle to lose power/stall. *ak
- Fuel system, gasoline › Fuel injection system
Strong fuel fumes in passenger compartment at any speeds
- Fuel system, gasoline › Fuel injection system
2 injectors have failed, o-rings replaced and still smell gas in the vehicle
- Fuel system, gasoline › Fuel injection system
Fuel injector IS cracked, causing the fumes to leak out and get into vehicle. Gas smell IS very strong. *ak
- Engine and engine cooling › Exhaust system › Emission control › Catalytic convertor
While driving at 55 mph the catalytic converter came off on the highway, causing the vehicle to cut off. consumer contacted the dealer. The dealer took off the other part of the converter. also three other parts, including the parts from the heat shield were replaced. Please provide any further details. *ak
- Engine and engine cooling › Engine
Chain assembly failed.
- Fuel system, gasoline › Fuel injection system › Injectors
When vehicle IS being driven there IS a smell of fuel in the passenger's compartment because the fuel injection system IS leaking. Dealer has not seen. *Ak
- Fuel system, gasoline › Fuel injection system
The consumer has been experiencing problems with fuel injection system. while driving they could smell gasoline very heavy. when they took vehicle to the mechanic, they said that there was a leak in the fuel injection system. the manufacturer has yet to be contacted. *ak
- Engine and engine cooling › Engine
Timing chain bracket broke and the valves were ruined. dealer aware of the problem, and stated the bracket was redesigned. No tsb, no indication or warning of incident when driving. dealer cannot duplicate the problem. *Ak
- Engine and engine cooling › Engine
Technical bulletin #ntb95-027, advised mechanics to replace plastic side timing chain guide with a steel-backed guide after the plastic one breaks. for this vehicle the guide broke and caused the timing chain to strike the engine components, ruining the engine. this resulted in engine suddenly would not start, with no prior problems.
- Electrical system › Wiring
Car was parked, saw smoke coming from the engine and fire started, took vehicle to dealer , the electrical wire harness had to be replaced . Please describe. *ak
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Fuel leaks from fuel injectors
In October of 1995, Nisan conducted a safety improvement campaign, 95I-006.The campaign recalled Maximas (1985-88), 200SX (1987-88), 300ZX (1984-88, and Infinity M30 (1990-92), for fuel leaking from the fuel injectors.The remedy called for a replacement of the fuel injectors and related hoses on the affected…
In October of 1995, Nisan conducted a safety improvement campaign, 95I-006.The campaign recalled Maximas (1985-88), 200SX (1987-88), 300ZX (1984-88, and Infinity M30 (1990-92), for fuel leaking from the fuel injectors.The remedy called for a replacement of the fuel injectors and related hoses on the affected vehicles.The recall was influenced by EA94-018, involving over 680,000 1984-89 Maxima and 300ZX vehicles, and was originally initiated as PE94-018 with 25 complaints, for a complaint rate of 4 per 100K.ODI has received 34 complaints for the 1990-92 Stanzas and 240SXs, for fuel leaking in the engine compartment from the fuel injectors, for a complaint rate of 10 per 100K.Fuel in the presence of an ignition source can lead to a vehicle fire.The purpose of this investigation is to evaluate whether the 1990-92 Stanzas and 240SXs should be recalled.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235729RADIO INTERMITTENTLY REBOOTS DURING AUDIO PLAYBACK VIA BLUETOOTH CONNECTED IPHONE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10206391STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
- 10192145SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
- 10188377STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10051767Nissan: lock/unlock request button on outside handle does not respond.
- 10032506Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (D40 series) only, install the protector listed in parts information. Includes 2005-09 frontier. Updated 12/8/10.
- 10031305Nissan: tire pressure monitoring system (TPMS) warning light on/flashing. No models or model years listed. Updated on 08-11-2011.
- 10030165Nissan: the 12 volt battery IS an important part of the vehicle electrical system and IS required to stay connected when the engine IS running. To prevent damage to vehicle electronic components follow the instructions/cautions. No model years listed.
- 4020100Unknown
- 39921K24E tension side timing chain guide broken.
Every Nissan Stanza model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.