2017 Peterbilt 389
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Peterbilt › 389 › 2017
These records cover every 2017 Peterbilt 389. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2017 Peterbilt 389. Newest first.
PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power…
Risk and remedy
Risk
If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.
Remedy
PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.
PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.
Risk and remedy
Risk
An electrical short circuit can increase the risk of a fire.
Remedy
PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.
PACCAR Incorporated (PACCAR) is recalling certain 2017-2019 Kenworth C500, T600, T660, T680, T800, T880 and W900 trucks, as well as Peterbilt 367, 386, 389, 567, 579 and 587 trucks, equipped with Cummins ISX15 or X15 diesel engines. In certain driving conditions, such as on a long down-hill grade, the fuel line may burst if the fuel pump cooling circuit…
Risk and remedy
Risk
If the fuel line bursts, fuel may leak onto the road resulting in a roadway hazard for other motorists. The engine may also stall without warning, resulting in the vehicle's inability to restart, increasing the risk of a crash.
Remedy
Cummins will notify owners, and dealers will replace the suspect fuel pump cooling circuit screen, free of charge. The recall began November 21, 2018. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 18E081.
PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 367, 389, 567, 579 and 587 trucks, and 2018 Kenworth C500, T680, T800, T880 and W900 trucks equipped with Cummins ISX 15L engines. These engines have a fuel pump whose drive gear could possibly slip on its drive shaft, causing a fuel pump function loss, resulting in an engine stall.
Risk and remedy
Risk
An engine stall can increase the risk of a crash.
Remedy
Cummins will notify the vehicle purchaser, and Cummins dealers will replace the fuel pumps, free of charge. The recall began July 1, 2017. Owners may contact Cummins customer service at 1-800-286-6467 or PACCAR customer service at 1-425-468-7400. PACCAR's number for this recall is C1909.
PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Peterbilt 325, 330, 337, 348, 365, 367, 386, 389, and 587 vehicles manufactured April 20, 2016, to June 13, 2016. The brake lights may not illuminate when the brakes are applied. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS)…
Risk and remedy
Risk
If the brake lights do not illuminate when the brakes are applied, other drivers will be unaware the vehicle is stopping, which can increase the risk of a crash.
Remedy
PACCAR will notify owners, and dealers will inspect and replace any brake light switches with date code 08-01760, free of charge. The recall began on January 26, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000. Paccar's number for this recall is 816-F.
PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Kenworth K370, T270, T370, T440, T660, T800 trucks manufactured February 2, 2016, to October 13, 2016, and Peterbilt 330, 337, 348, 367, 389, 567, and 579 trucks manufactured March 7, 2016, to October 5, 2016. The affected vehicles are equipped with certain Goodyear LHS Load Range G tires…
Risk and remedy
Risk
A partial tread separation may increase the risk of a crash.
Remedy
Goodyear will notify the owners of the affected Peterbilt and Kenworth vehicles and Goodyear dealers will replace the affected tires, free of charge. The recall began on December 14, 2016. To find a Goodyear dealer, owners should contact Goodyear Consumer Relations at 1-800-592-3267. Consumers may also contact Kenworth customer service at 1-425-828-5000 and Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1016G (PB) (Peterbilt), and 16KWC (Kenworth).
PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Kenworth C500, T660, T680, T800, T880, and W900 vehicles manufactured March 9, 2016, to April 26, 2016 and 2017 Peterbilt 320, 365, 367, 389, 567, 579, and 587 vehicles manufactured March 10, 2016, to May 6, 2016. The affected vehicles are equipped with Cummins ISX12 or ISX15 engines and…
Risk and remedy
Risk
An engine stall can increase the risk of a crash.
Remedy
Cummins will notify owners, and Cummins dealers will replace the defective engine control modules, free of charge. The began on July 8, 2016. Owners may contact Cummins customer service at 1-800-343-7357, Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 16KWB (Kenworth) and 616-C (Peterbilt).
Owner complaints
1 complaints
What owners report most
Latest complaints
- Electrical system · Power train
Heat from the new def requirements are causing problems. The heat off of the def system stays trapped under the vehicle. Which IS causing early wear on electrical harnesses along with axle seals. I've replaced 3 wheel seals and 2 front differential seals. The def harness has failed twice now.…
Heat from the new def requirements are causing problems. The heat off of the def system stays trapped under the vehicle. Which IS causing early wear on electrical harnesses along with axle seals. I've replaced 3 wheel seals and 2 front differential seals. The def harness has failed twice now. Please look into this. The heat stays under these vehicles. And the manufacturer will not accept responsibility for this. *Dt*jb
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Quarter Fender Failures
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE21-015) based on one Vehicle Owner Questionnaire (VOQ) and supporting fleet reports. The reports indicated that the subject quarter fenders were prone to cracking and/or separation.After a comprehensive review of the data related to the…
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE21-015) based on one Vehicle Owner Questionnaire (VOQ) and supporting fleet reports. The reports indicated that the subject quarter fenders were prone to cracking and/or separation.After a comprehensive review of the data related to the quarter fender failures on the subject vehicles, ODI did not identify the existence of a safety-related defect trend. Quarter fender failures resulted in a warranty claim rate less than one percent (<1%) of the total vehicle population. All separations, including those due to tread separations, road hazards, etc., accounted for less than point one percent (<0.1%) of the total vehicle population.ODI discovered that the minimum recommended gap between the top of the quarter fender and the bottom of the trailer was not known or being followed. The optional quarter fenders were supplied by Fontaine Spray Systems (FSS), who recommended a two inch (2) gap. ODI analyzed the claim data using a calculated gap. A calculated gap using the top of the quarter fender flap and assuming the trailer is level with the top of the fifth wheel hitch was necessary, as PACCAR doesn't know specifically what trailer a purchaser will couple to the tractor. It is safe to assume no trailers on the market extend below the upper fifth wheel plate, but many do provide additional clearance over the wheels where the quarter fenders are located. ODI determined that 94 percent of warranty claims and 84 percent of separations violated FSS' recommendation.ODI confirmed that the VOQ vehicle and the fleet report vehicles also violated FSS' recommended gap. In one fleet the gap was negative point three inches (-0.3).PACCAR has updated its vehicle specification process and issued a customer advisory notice to existing owners. In light of the low rate of reported failures and separations, further use of agency resources does not appear to be warranted. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves the right to take further action if warranted by the circumstances.
- Intermittent Loss of Power Steering Assist
On May 1, 2020, the Office of Defects Investigation (ODI) opened PE20006 to investigate complaints of intermittent loss of power steering assist in Daimler Truck North America (DTNA), Volvo Trucks of North America (Volvo) and PACCAR vehicles equipped with a ZF/TRW (TRW) THP60 steering gear. The investigation focused…
On May 1, 2020, the Office of Defects Investigation (ODI) opened PE20006 to investigate complaints of intermittent loss of power steering assist in Daimler Truck North America (DTNA), Volvo Trucks of North America (Volvo) and PACCAR vehicles equipped with a ZF/TRW (TRW) THP60 steering gear. The investigation focused on 2010-2020 DTNA Freightliner Cascadia, M2 and WST; Volvo VN, VAH and VHD and PACCAR 337, 365, 389, 567, 579 model vehicles.Field reports and interviews with fleet drivers allege that high power steering fluid temperatures could result in internal seal and bearing failures causing pressure fluctuation, affecting left and right-hand turns. The inability of the driver to steer the vehicle as intended can increase the risk of a crash and injury. ODI analyzed data provided by TRW, DTNA, Volvo, and PACCAR in response to individual information request letters.ODI found that most failures occurred within the first two years and/or 50,000 miles of service. The claim rate decreased with time and miles in service and remained less than 0.5%. ODI normalized data from each of the manufacturers and determined that there was not a substantial difference in the failures.Additionally, TRW improved a seal in the steering gear in December 2015.Trucks built on or after 2016 (as 2017 and newer model years) show a decreasing trend of failures. In view of the overall low failure rate, the nature of early-life failure, and failure rate trending downward for model years 2017 and newer, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010926Info Only Unnecessary starter replacements can result from customer complaints regarding engine starting issues. A new Starter Troubleshooting Guide has been created to provide a comprehensive list of starting system checks, which should reduce unnecessary starter replacements and associated warranty claims. Engine starting system warranty claims now require a completed Starter Checklist, a Battery Pack Midtronics Report, and a Cable Drop Midtronics Report. Claims filed without these documents may be denied.
- 11010896Fix-As-Fail The window switch fails prematurely due to excessive amperage flowing through the window switch circuit. A new door harness design has been developed to prevent failures. Fix-As-Fail start date is 11/11/2024.
- 110097577/700 Service Agreement - Letter Only.
- 10244495Emissions Recall Certain vehicles with PACCAR MX-11 and MX-13 EMY2016 engines with less than 300,000 miles (482,803 km) have been shown, in testing, to exceed regulatory limits for NOx and N2O emissions. This bulletin now applies to both Canadian and U.S. registered vehicles. Software is now available to remedy this emissions non-compliance.
- 10238379An engine software defect exists in certain vehicles equipped with EMY17 MX-13 and MX-11 engines that pertains to timer action and count calibrations for a time-based diagnostic. This diagnostic action checks fuel pressure and has no negative impact on tailpipe emissions. This soft ware may incorrectly set DTC P1092.
- 10232162Fix As Fail Chassis that were manufactured with certain battery cable routing brackets may experience rubbing or chafing of the battery cables.
- 10227181Certain model 389 chassis are experiencing freezing of the A/C evaporator or frosting of the compressor and suction line. A field resolution is available to solve this issue.
- 1022716734-093 Model 389 78-inch Sleeper 12V Power Port Supplier Change
- 10225580Clutch pedal linkage lubrication service interval information is missing from the Service manual for Model 365, 367, and 389 chassis.
- 10225578Info Only - PACCAR is introducing Over-the-Air (OTA) software updates for engine MY17 and newer chassis equipped with Cummins X15, X12, ISX12, ISX12N, L9N, PX-7, and PX-9 engines The technology will leverage the existing Remote Diagnostic cs hardware to deliver secure software updates remotely. This will reduce downtime and save on maintenance costs for eligible vehicles.
- 10222269Fix-As-Fail On certain chassis with Low Air Leaf Suspension or Low-Low Air Leaf Suspension, the Height Control Valve (HCV) arm may be rubbing on other components when the bend in the arm is facing outboard. Flipping the bend in the HCV arm inboard prevents the rub.
- 10219235The service information for Bendix Air Dryer maintenance is being updated to include new procedures.
- 10208758Due to major data carriers phasing out 3G networks, chassis currently utilizing first generation Peoplenet Mobile Gateway (PMG001) will experience severe 3G service degradation as early as January of 2022. Chassis currently utilizing 3G antennas as a primary antenna may experience this degradation.
- 10201965Fix-As-Fail Due to undersupply issues, only a limited supply of Diesel Exhaust Fluid (DEF) sensors are available. As a temporary solution, after PACCAR confirms a DEF sensor is not available, a temporary software update will allow a vehicle to continue operation with a failed DEF sensor by disabling the DEF sensor diagnostics.
- 10198760An engine software update is required to resolve OBD system readiness, DEF doser diagnostics, and otherOBD system software related issues.
- 10195277Sample Customer Letter - Field Repair 11151: Steering Column Mounting Bolts Loose.
- 10195274Sample Customer Letter - 216-1 Dana Intermediate Steering Shaft Unseated or Missing C-clip.
- 10194769Selected engines have been identified to receive a camshaft inspection and an update for improved camshaft lubrication.
- 10188550Information Only Windshield washer pumps have a high No Trouble Found rate. Washer pumps may fail to spray due to a clogged filter.
- 10186168SmartNav 2.0 Hardware retrofit for quality validation and vehicle validation units.
- 10179370Fix as Fail: Peterbilt has determined that certain model 348, 365, 367, 382, 384, 386, 388, 389, 567, 579, and 587 trucks, built between 4/13/2010 and 3/16/2020 and equipped with a flush mounted battery box, utilized rubber washers that could rub through and cause the aluminum box mounting tabs to rub directly on the steel frame brackets. This could result in cracked battery box mounting angles. Resolution is to add the reinforcement bracket(s) to affected vehicles.
- 10177935Fix-As-Fail - Bendix New-Gen Lightweight Steer Axle Drum Brake Spider Cracking
- 10177021Information Only: This bulletin provides dealers with a battery warranty quick reference guide to ensure the appropriate tests for battery warranty are performed in order to prevent battery warranty claims filed with incorrect or incomplete information.
- 10177019Fix as Fail: For all conventional models, except 387/587, equipped with Side-of-Cab (SOC) exhaust and built from 03/6/2006 to 1/20/2020, the clamps that secure the SOC exhaust stacks may not be tightened properly. This may allow the exhaust stack to rotate and contact the cab or sleeper.
- 10176033Information only: Hendrickson Softek front axle maintenance intervals and requirements.
- 10174764Safety Recall Bulletin: Updated with permanent repair path for phase 1 vehicles. The Tractor ABS Lamp May Not Illuminate When ABS Controller Loses Battery and/or Ignition Power. NHTSA recall number is 18V368. Non compliance to FMVSS and CMVSS 121 and 136. Resolution is to Reflash software.
- 10174763"Safety Recall: NHTSA recall number is 20V130. A defect, which relates to motor vehicle safety, may exist in certain Model 365, 389, 567, and 579 vehicles manufactured between April 18, 2014 and March 09, 2020 with a left-hand under hood jumper start terminal. Jumper terminal battery cables may be too long, or eligible for improved routing. Battery cables that are too long may chafe against the left front suspension leaf spring, which could cause a short circuit, fire under the hood, or increased risk of crash. "
- 10174762Safety Recall Interim Bulletin: The Tractor ABS Lamp May Not Illuminate When ABS Controller Loses Battery and/or Ignition Power. NHTSA recall number is 20V199 Non compliance to FMVSS and CMVSS 121 and 136. Resolution is to Reflash software.
- 10173583DEF tank covers may become loose and potentially crack on vehicles built before October 2019 with DEF tank part number M86-6221-003**(TANK-DEF MEDIUM ASSY) and M86-6222-003**(TANK-DEF LARGE, ASSY). Resolution is to resolve the vibration on the tank cover by adding bottom tank washers.
- 10173212Information Only Vehicles may have the connector seals on the wheel speed sensor incorrectly installed, which may lead to water intrusion and corrosion in some vehicles.
- 10173211Safety Recall Interim Bulletin: Peterbilt has decided that a defect, which relates to motor vehicle safety, may exist in certain Model 365, 389, 567, and 579 vehicles manufactured between April 18, 2014 and September 30, 2019 with a left-hand under hood jumper start terminal. Your vehicle may have jumper terminal battery cables that are too long, or are eligible for improved routing. Battery cables that are too long may chafe against the left front suspension leaf spring, which could cause a short circuit, fire under the hood, or increased risk of crash.
- 10173205Information Only: Proper jump-starting voltage will eliminate high voltage related issues and equipment damage.
- 10172036Information Only: Vehicles may have the connector seal on the wheel speed sensor incorrectly installed, which may lead to sensor corrosion.
- 10169787Information Only - Vehicles built with NAMUX software from 2013 to present may experience accuracy issues with the tachometer. The issue can be temporarily resolved using any one of the included procedures.
- 10168703Information Only: This bulletin provides guidance for repairing an air-conditioning system after internal failure of the A/C compressor.
- 10165711Non Safety Campaign: Peterbilt has determined that certain Model 365, 384, 386, 388, 389, 3895, 587 and 579 vehicles built between March 27, 2012 and January 20, 2019 with Flex Air suspension in a 6x2 configuration have U-bolts that may fail prematurely.
- 10165583Information Only This bulletin provides information about the California Air Resources Board (CARB) Periodic Smoke Inspection Program (PSIP) and Heavy Duty Vehicle Inspection Program (HDVIP).
- 10164378Fix-As-Fail - Composite fittings used in the cooling system may crack, resulting in coolant leaks. Brass fittings are available to replace the composite fittings.
- 10164375Fix-As-Fail: Two separate causes have been identified as root cause of intermittent low coolant indicator illumination.
- 10162392Information Only - Quick Reference Guide for Electric harness damage repairs.
Every Peterbilt 389 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.