2018 Toyota Prius Prime

Owner complaints

What owners report most

1. Unknown or other3
2. Back over prevention2
3. Power train2
4. Fuel/propulsion system2
5. Air bags2
6. Latches/locks/linkages1
7. Service brakes1
8. Structure1
9. Vehicle speed control1
10. Visibility1

Latest complaints

• Mar 10, 2026KS
  Power train

  On at least 4 occasions when the EV battery becomes depleted while driving at highway speeds and the car is switching to gas, the engine completely loses all power. This has lasted from 10-30 seconds. The dealership said a small battery needed to be replaced, and replaced that, but this recurred within a month of replacement.

• Mar 4, 2026HI
  Unknown or other
  There has been at least 4 times that the vehicle was not responsive to acceleration (stalled for a few seconds) then picked back up. Problem has been intermittent. There is no dash indication of an issue. Because concern is intermittent I haven’t taken vehicle in. There is NO CHECK ENGINE light on.…

  There has been at least 4 times that the vehicle was not responsive to acceleration (stalled for a few seconds) then picked back up. Problem has been intermittent. There is no dash indication of an issue. Because concern is intermittent I haven’t taken vehicle in. There is NO CHECK ENGINE light on. My wife experienced it once, I’ve experienced it 3 times. Once going up steep hill, once on a steady incline and the other 2 times at 50 mph on the highway. My layman’s take points to an Inverter issue in the IPM. Intelligent Power Module having a voltage issue that causes vehicle to stall.

• Feb 26, 2025CT
  Visibility › Defroster/defogger/hvac system
  Hi, My Prius Prime recently just suffered the loss of heat in the middle of winter. Based on the diagnostic of my local Toyota dealer, it appears one of the metal heater coolant hose had rusted off. This is not just causing a safety issue of having no issue, it is also a risk as the engine can…

  Hi, My Prius Prime recently just suffered the loss of heat in the middle of winter. Based on the diagnostic of my local Toyota dealer, it appears one of the metal heater coolant hose had rusted off. This is not just causing a safety issue of having no issue, it is also a risk as the engine can now overheat and suffer permanent damage. Despite being such a serious problem, Toyota doesn't stock the part nor does it know when the new part will come. I am currently owning an asset that can't be safely driven, I would like the NHTSA to review this. Toyota seems to be aware of this issue as they have a TSB out on a similar heater coolant hose. With that said, having no part is not an acceptable option. NHTSA, please step in

• Oct 1, 2024CT
  Latches/locks/linkages › Hood › Latch

  As I was driving on a local highway going approximately 50 mph, the hood of the vehicle released and hit the windshield with full force. Luckily there was no traffic on the local highway at the time of the incident. I did not release the hood at all, and the dealer reports verbally to me that the hood latch is damaged. The incident could have resulted in my death if it happened on the highway.

• Nov 6, 2023ILCrash
  Structure › Body · Unknown or other · Vehicle speed control
  My 2018 Toyota Prius Supreme was parked too far away from the curb in front of a house where we were invited, in a residential area in Naperville IL. I entered the car to park it properly. I had my foot on the brakes and pressed the starting button for the engine to turn on. I then put the car…

  My 2018 Toyota Prius Supreme was parked too far away from the curb in front of a house where we were invited, in a residential area in Naperville IL. I entered the car to park it properly. I had my foot on the brakes and pressed the starting button for the engine to turn on. I then put the car on reverse and suddently the car accelerated uncontollably. Went on the grass, hit the neighbor's mailbox and stopped by crashing on a tree. I was in shock but luckily not injured. Other guests were present and witnessed the incident. Police was called in and issued a report. The car was declared by Progressive Insurance Co as a total loss.

• Aug 15, 2023CACrash2 injuries
  Air bags
  Airbags deployed prematurely as I was parking my car in a doctor's office parking lot. The car was going less than 5 mph and I did not hit anything. The premature deployment of the airbag startled me and caused me to hit the accelerator instead of the brake and I ended up crashing my car into a…

  Airbags deployed prematurely as I was parking my car in a doctor's office parking lot. The car was going less than 5 mph and I did not hit anything. The premature deployment of the airbag startled me and caused me to hit the accelerator instead of the brake and I ended up crashing my car into a nearby pole and another .automobile. The accident resulted in a soft tissue injury for my daughter and I'm experiencing lower back pains. The air bag caused burns on my nose and arms. My daughter has bruising on the arms from the air bag deployment

• Apr 14, 2023CA
  Power train
  Take foot of break, car accelerates under power. Sooner or later, this is going to result in killing a pedestrian. The question has been for the last year, is this a behavior that can be gotten used to. The answer is definitely NO! This resulted in a near collision with a pedestrian today. Toyota…

  Take foot of break, car accelerates under power. Sooner or later, this is going to result in killing a pedestrian. The question has been for the last year, is this a behavior that can be gotten used to. The answer is definitely NO! This resulted in a near collision with a pedestrian today. Toyota believes the behavior is intentional and will not confirm the safety issue. Farmers Insurance is willing to believe the issue exists without inspection but has no idea what to do. You have a problem on your hands. Biden is trying to transition almost everybody away from gasoline vehicles; thus those that drive manual transmissions will be driving electric vehicles, and their brain patterns have not changed and the procedure for getting rolling from a dead stop will be done the old way, and it's now dangerous. In a manual transmission it is necessary to transition off the break before completing looking all three ways (left, right, straight) because the transition time from break to power is so long that if the looking is done before, it is out of date by the time power is being applied. Applying the same procedure to an electric car has potentially lethal results; and people who have been driving a manual transmission for a long time will end up using its procedure in an electric car by habit. Perhaps you observed the reports over the last few decades of old men with new cars having unintended acceleration problems with no cause found. I now believe that a number of these have a very similar explanation. Car isn't off, take foot of break to get out of car, car accelerates. In an electric car, telling the car isn't off isn't very easy any more. This is easy to understand. An automatic transmission vehicle has an unremovable dumb behavior where take foot off break accelerates, whereas in a manual transmission this stalls, which is a safer result. There is no reason this behavior should carry over to computer drive, including electric or hybrid vehicles.

• Jan 19, 2023CACrash1 injury
  Air bags

  Air bag did not deploy during a head on collision at 25-30 mph. No warning lamps. Car is totaled according to tow truck driver. Currently at the body shop, waiting for adjusters approval for body shop to take car apart to assess the damage.

• Oct 3, 2022CA40,063 miCrash
  Service brakes
  The contact owns a 2018 Toyota Prius. The contact stated while driving approximately 5 MPH and in heavy traffic, the contact depressed the brake pedal for traffic but the brakes failed. The contact stated no warning light was illuminated. The contact crashed into the rear end of a truck. The damage…

  The contact owns a 2018 Toyota Prius. The contact stated while driving approximately 5 MPH and in heavy traffic, the contact depressed the brake pedal for traffic but the brakes failed. The contact stated no warning light was illuminated. The contact crashed into the rear end of a truck. The damage was very light due to the low speed. The top of the hood at the front was scratched and the grill also sustained minor scratches. The contact continued on the road. The contact had taken the vehicle to a local dealer, who contacted a manufacturer representative to diagnose the vehicle. The contact was advised that there was no brake failure. The vehicle had not been repaired. The manufacturer had been informed of the failure. The failure mileage was 40,063.

• Jul 22, 2021NJ
  Back over prevention › Rearview system braking · Back over prevention › Warnings · Forward collision avoidance › Warnings
  From the first week of ownership sensors would alarm that they needed cleaning but they were clean. Parking assist sensors also malfunctioning. Also saw Intelligent Clearance Sonar error messages and warnings. Alarm tended to go off in wet weather. Brought to dealership many times and problem…

  From the first week of ownership sensors would alarm that they needed cleaning but they were clean. Parking assist sensors also malfunctioning. Also saw Intelligent Clearance Sonar error messages and warnings. Alarm tended to go off in wet weather. Brought to dealership many times and problem occurred infrequently that no problem was ever found. For two years I was plagued by alarms of sensor malfunction. I worried the sensors would fail to detect cars and objects in front of, behind or on the side of the car. That would be a serious failure and cause of an accident. After two years of unsuccessful testing, I traded in the car.

• Jan 28, 2021OK15,000 mi
  Exterior lighting
  While driving on rural roads with no street lights, the automatic high beam system malfunctions when passing oncoming traffic who do not dim their headlights or who have those headlights that should be illegal (like ford). Normal low-beam headlights do not cause the system to malfunction. I believe…

  While driving on rural roads with no street lights, the automatic high beam system malfunctions when passing oncoming traffic who do not dim their headlights or who have those headlights that should be illegal (like ford). Normal low-beam headlights do not cause the system to malfunction. I believe this malfunction to be related to the camera sensor located on the windshield and when the glare of the excessively bright headlights hit that sensor, it crashes the auto system. The symbol on the dash that indicates that the system IS working normal cuts off for approximately 25-30 seconds, during which time the high beams will not engage. After that 30 second delay, the system reboots, the light on the dash comes back on and the high beams re-engage. This IS dangerous as all manner of wildlife cross that road at night and without bright lights, my reaction time IS cut in half. I have talked to the toyota dealership about this issue since I purchased this car in may of 2019 telling them there IS a malfunction in the system, and was initially informed that this was normal functionality. I owned a 2017 prius prime advanced (one year older than this one) and it never malfunctioned, so I know this IS a malfunction in the system. After speaking with the service manager in depth about my experience with this issue, he finally understood that this IS an issue and not normal functionality. They have kept my car several times trying to recreate the failure, but unless they drive out in the middle of nowhere (super dark) and come across someone with "too-bright" headlights, it IS unlikely they will accomplish a failure. I was also told that toyota did not know anything about this issue. I have since done the research and found that this has been an issue since at least 2017, and occurs on various toyota models (prius, avalon, RAV4, etc...). I have video of the failure.

• Jan 12, 2021CA39,300 mi
  Fuel/propulsion system

  Supplement to complaint # 11384074 the vehicle had the same problem on january 11 and 12, 2021 at approximately 7 am. Speed was 76 mph, and the fuel deprivation occurred for 8-10 seconds each time. the vehicle has never had the problem going home at 2 pm.

• Dec 18, 2020CA20 mi
  Engine
  After the hybrid battery IS discharged, and the gas engine kicks in, the vehicle loses power for approximately 5-10 seconds on the freeway. This has happened four times, at approximately 7 am, on december 1, 10, 14 and 15. On all occasions, the temperature was between 40-45 degrees fahrenheit, and…

  After the hybrid battery IS discharged, and the gas engine kicks in, the vehicle loses power for approximately 5-10 seconds on the freeway. This has happened four times, at approximately 7 am, on december 1, 10, 14 and 15. On all occasions, the temperature was between 40-45 degrees fahrenheit, and at highway speeds. The cruise control was not in use. No warning lights came on. I called the toyota dealer on december 1 and the service adviser said that since no warning lights came on, he could not determine the problem. I have a photo showing my contacting the toyota dealer on december 1ST. on december 10, I took the vehicle into toyota in the afternoon. The dealer checked the vehicle and road tested the vehicle without having the hybrid battery charged, and the air temperature was warmer. I was charged $210 for the diagnostic service, although I have an extended warranty. The same problem occurred on december 14 and 15. specific problem unknown but I believe that a switch that controls the gasoline volume into the engine after the hybrid battery power IS depleted IS defective. I was in the carpool lane at approximately 7 am on all 4 occasions and my speed dropped, although I depressed the gas pedal to maximum as well as pumping the gas pedal, all to no avail. The car IS in use only monday, tuesday, wednesday and thursday, the days that I work. I contacted toyota customer advocate (800-331-4331, case # 2012120505) and they said they did not have the ability to determine if anyone else ever had the same problem.

• Nov 11, 2020CA15,000 mi
  Electrical system · Fuel/propulsion system
  'Hybrid system failure' appeared on dash display during a long (120 mile) drive at highway speed on september 24. After driving about 40 miles further, the 'check engine light' came on and the display said to pull over immediately. As I pulled off the freeway, messages told me the power steering…

  'Hybrid system failure' appeared on dash display during a long (120 mile) drive at highway speed on september 24. After driving about 40 miles further, the 'check engine light' came on and the display said to pull over immediately. As I pulled off the freeway, messages told me the power steering and power brakes were shutting off and left me in fear the car would die on the freeway ramp before I could pull over. Towed car to dealer who fixed a loose cable. this week (11/10) the display showed the same message. This IS now a recurring problem with this model.

• Feb 6, 2020CA22,500 mi
  Unknown or other
  After starting from a stop after the traffic light turned green, the car in front of me pulled ahead as they accelerated faster than me. When the car in front of me was about 50 yards in front of me, and I had reached about 25 miles per hour the car's collision avoidance system engaged and slammed…

  After starting from a stop after the traffic light turned green, the car in front of me pulled ahead as they accelerated faster than me. When the car in front of me was about 50 yards in front of me, and I had reached about 25 miles per hour the car's collision avoidance system engaged and slammed on the brakes and brought me to a full stop. The car in front of me had not applied their brakes or slowed at all, and there were no visible obstacles. My car stopped so suddenly that I thought I had been hit from the rear at high speed until the red warning lights appeared on the dash (after the braking started). The cars behind me almost ran into me because of the sudden stop.

• Feb 21, 2018NC550 mi
  Visibility/wiper
  Driving 60 mph on interstate a piece of debris hit my windshield. The piece was so small I didn't even see it hit the windshield. the piece did pretty significant damage to the windshield and it spidered out in all different directions, larger than a quarter. my concern IS that I have been in…

  Driving 60 mph on interstate a piece of debris hit my windshield. The piece was so small I didn't even see it hit the windshield. the piece did pretty significant damage to the windshield and it spidered out in all different directions, larger than a quarter. my concern IS that I have been in other vehicles and had debris hit the windshield the same situation that IS larger and just barley put a nick in the windshield. ive read on complaints about 16' and 17' models having this issue as well and it doesn't seem like toyota IS addressing the issue. I am worried about the structural integrity of my windshield.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
• 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
• 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
• 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
• 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
• 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
• 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
• 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
• 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
• 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11003636Some 2020 2024 Corolla HV, 2017 2022 Prius Prime, and 2016 2022 Prius vehicles equipped with a 2ZR-FXE engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P210015 (Throttle Actuator "A" Control Motor Circuit Short to Battery or Open), or P210019 (Throttle Actuator "A" Control Motor Circuit Current Above Threshold), or P211172 (Throttle Actuator "A" Control System Actuator Stuck Open) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. REVISION NOTICE April 17, 2024 Rev1: The Required Tools & Equipment section has been updated.
• 11003619Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
• 11003602Some 2020 2024 Corolla HV, 2017 2022 Prius Prime, and 2016 2022 Prius vehicles equipped with a 2ZR-FXE engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P210015 (Throttle Actuator "A" Control Motor Circuit Short to Battery or Open), or P210019 (Throttle Actuator "A" Control Motor Circuit Current Above Threshold), or P211172 (Throttle Actuator "A" Control System Actuator Stuck Open) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition
• 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
• 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
• 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
• 11003581Some 2020 2024 Corolla HV, 2017 2022 Prius Prime, and 2016 2022 Prius vehicles equipped with a 2ZR-FXE engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P210015 (Throttle Actuator "A" Control Motor Circuit Short to Battery or Open), or P210019 (Throttle Actuator "A" Control Motor Circuit Current Above Threshold), or P211172 (Throttle Actuator "A" Control System Actuator Stuck Open) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition. REVISION NOTICE April 17, 2024 Rev1: The Required Tools & Equipment section has been updated.
• 11003564Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
• 11003547Some 2020 2024 Corolla HV, 2017 2022 Prius Prime, and 2016 2022 Prius vehicles equipped with a 2ZR-FXE engine may exhibit a MIL ON condition with Diagnostic Trouble Code (DTC) P210015 (Throttle Actuator "A" Control Motor Circuit Short to Battery or Open), or P210019 (Throttle Actuator "A" Control Motor Circuit Current Above Threshold), or P211172 (Throttle Actuator "A" Control System Actuator Stuck Open) present. The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to reduce the possibility of this condition
• 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
• 10251744PANT: Toyota is pleased to announce to all field and dealer personnel that we have launched a new part number to the Toyota Complete Maintenance Care (TCMC) Program, effective February 1, 2024. This new H4 Battery will be phased in over time as inventory levels for the current part number are depleted. Additionally, this new part number will have the same pricing as the current part number and will be drop shipped by an Interstate Battery Distributor.
• 10247820TSB: Some 2016 ? 2023 model year Toyota vehicles may exhibit a hybrid system warning lamp occurring in below-freezing temperatures (below 32F or 0C). After performing a Health Check, one or both of the following Diagnostic Trouble Codes (DTCs) may be present: ?P1C8449 ? (High Voltage Power Resource Circuit Short during Ready ON) ?P300449 ? (High Voltage Power Resource Circuit Short during Pre-Charge) Follow the Repair Procedure in this bulletin to address this condition.
• 10247796TSB: Some 2016 ? 2023 model year Toyota vehicles may exhibit a hybrid system warning lamp occurring in below-freezing temperatures (below 32F or 0C). After performing a Health Check, one or both of the following Diagnostic Trouble Codes (DTCs) may be present: ?P1C8449 ? (High Voltage Power Resource Circuit Short during Ready ON) ?P300449 ? (High Voltage Power Resource Circuit Short during Pre-Charge) Follow the Repair Procedure in this bulletin to address this condition.
• 10244115TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
• 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
• 10244111TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.
• 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
• 10224108TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
• 10224102TSB: Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010144), Entune? Audio Plus (version 01015E), Entune? Premium Audio (version 010182), or earlier may exhibit one or more of the following conditions: ?Head unit reboots intermittently. ?Home screen intermittently half blank after shifting out of reverse, if the driver uses reverse after using the maintenance reminder screen. ?Screen freezes during an incoming phone call. ?Incorrect time displays on the diagnostic menu. ?Radio station information does not match the radio station that is playing.?Abnormal playlist browsing operation. ?Mute stays enabled after key cycle. ??Search along my route? is inoperative. ?Traffic data scales improperly. ?Unit of measure is missing from distance to destination (showing ?11? instead of ?11mi/km?). ?Multi-information display (MID) compass does not match navigation screen when switching to North up. ?Navigation does not match MID when switching from miles to kilometers. ?Speed limit is blank on navigation screen. ?Go button on VR screen is inoperative. Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 010145), Entune? Audio Plus (version 010161), Entune? Premium Audio (version 010189), or earlier may exhibit one of the following conditions: ?Map will not display after it has been reprogrammed from the map micro SD card. Updated system software is now
• 10220183TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
• 10220177TSB: Some 2016 ? 2018 model year Toyota vehicles equipped with Entune? Audio (version 01013E), Entune? Audio Plus (version 010156 or 01015C), or Entune? Premium Audio (versions 010171, 010170, or 01017D) may exhibit one or more of the following conditions: ?Head unit reboots at a specific location. ?Abnormal Destination Search app operation. ?Rebooting caused by no songs on the USB-connected iPhone. ?A one-time reboot after ignition is cycled to ACC-ON. ?Audio stays muted after the key is cycled.
• 10220154TT: To improve customer support of telematics connected services features, additional resources have been provided in the Service Lane - Knowledge Center.
• 10220150TSB: Some 2017 ? 2022 model year Prius Prime vehicles may exhibit corrosion on the back door steel reinforcement panel sub-assembly area visible below the opener switch and rear camera.
• 10220142OBSOLETE NOTICE May 02, 2022: This bulletin is now obsolete. Please see T-SB-0045-22
• 10217807TT: Mil On. DTC P0AFB11 (Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground), P0ABF15 (Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open), P0ABF28 (Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure), P0AA649 (Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure) or P33CF49 ( Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure Abnormal Area Detection Failure) present for HV Battery Current Sensor/Battery ECU

Every Toyota Prius Prime model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.