1990 Winnebago CW825FT
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Winnebago › CW825FT › 1990
These records cover every 1990 Winnebago CW825FT. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 1990 Winnebago CW825FT. Newest first.
Road debris may enter an opening in the rear suspension trailing arm and damage the bearing seal.
Risk and remedy
Risk
Vehicle stability may be impaired under certain roador operating conditions which may cause loss of vehicle control.
Remedy
Drill a 1/8 inch vent/drain hole, clean the bearing seal area, apply heavy washout resistant grease between the hub assembly and the trailing arm surfaces, and install a foam rubber plug into the angled opening at inboard side of the trailing arm.
The front and rear wheel hub retainer nuts have been incorrectly torqued. The preload on the bearing from the loosened hub retainer nut may cause bearing failure.
Risk and remedy
Risk
A wheel bearing failure may cause the axle to break,resulting in loss of vehicle control and possible vehicle accident.
Remedy
Inspect bearing and replace if necessary. Torque the hub retainer nut 230 to 350 foot pounds.
The horn activating switch components located in the steering column can wear abnormally.
Risk and remedy
Risk
The horn may be energized and sound constantly, or notenergize and fail. This could lead to an inabilty to warn other drivers ina crash situation, and result in vehicle damage and increased risk of injury.
Remedy
Replace the steering wheel hub and horn brush. Arrange the parts to avoid the premature wear conditions.
The lower ball joint retaining nut that holds the lower ball joint to the steering knuckle was not torqued correctly.
Risk and remedy
Risk
If the lower ball joint becomes disconnected from thesteering knuckle, the wheel will tip outward resulting in loss of steeringcontrol and a possible vehicle accident.
Remedy
Inspect lower ball joints, replace worn parts, and torque the lower ball joint mounting nut 130 to 150 foot pounds.
The steering gear intermediate shaft clamps used to retain the intermediate shaft to the steering gear shaft and the column shaft can become loose because of incorrect bolt size and clamp force.
Risk and remedy
Risk
Loose intermediate shaft clamps could wear smooth therespective splines of each connecting part and cause the assembly to fall apart.this results in loss of steering control and a possible vehicle accident.
Remedy
Replace the pinch bolts in the intermediate steering shaft assembly with 7/16" bolts. Torque bolts 63 to 75 foot pounds.
The steering gear mounting bracket bolts may become loose and allow the gear to move out of position.
Risk and remedy
Risk
The steering effort increases and may cause loss ofsteering control and a possible vehicle accident.
Remedy
Replace the mounting bolts; place a spacer plate between the steering gear mounting bracket and the left front frame; reattach the steering gear assembly mounting bracket to the frame using new hardened nuts torqued to 285 foot pounds.
The rear shock absorber bracket causes the rear shock absorber lower mounting hardware to fail prematurely.
Risk and remedy
Risk
The rear shock absorber may become detached and causedamage to surrounding components (tires, springs, etc.) which could lead toloss of vehicle control and an accident.
Remedy
Remove old shock absorber mounting brackets, reattach new brackets to frame, adapt shock absorbers and add a jounce pad spacer between each jounce pad and the new shock absorber brackets.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10226724Service Bulletin sent to all Winnebago dealers. Bulletin advises of a manufacturing change to the shower surround sealant process for all units.
- 10213593Service Bulletin sent to all dealers. This bulletin advises dealers they no longer need to email Winnebago the signed Vehicle Registration Form, but they should retain a copy for their records.
- 10199382Service Bulletin to dealers reminding them to understand their state's Lemon Law and to comply with Winnebago Motorhome mandates outlined in the Policy & Procedure Manual.
- 10199381Service Bulletin to dealers advising them of part sales training opportunities.
- 10199380General Parts and Service Letter to dealers detailing the warranty part return procedure.