Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The seat back of the driver and the three passenger seats can fail and separate from the seat section of the seat.
A lock nut which secures the tie rod to the inner ball joint of the steering system may not have been securely fastened on some of the involved vehicles during assembly. If this condition exists and the vehicle IS driven along poor roads…
Some of the involved vehicles may be susceptible to extensive rusting of the splined section of the lower steering shaft. This could prevent the splined shaft from moving into the sleeve. If this occurs, excessive stress IS applied between…
The involved tires may exhibit socketing around individual cords in the belt plies after extensive testing. This condition could lead to chunkout or separation in the tread area. Loss of inflating air may result.
The black plastic adaptor may give way if subjected to forces of the type sometimes applied by car owners to free wiper blades frozen to windshields under severe cold and heavy snow and ice conditions.
The involved vehicles may contain propane gas line flare nuts that may already be cracked or could crack at a later date. This could lead to gas leakage.
The involved tires do not conform to federal motor vehicle safety standard no. 109, "new pneumatic tires". These tires fail to meet the high speed and endurance test requirements.
The involved tires do not conform to federal motor vehicle safety standard no. 119, "new pneumatic tires for vehicles other than passenger cars". Flexing may develop in the lower sidewall under maximum tire loads and could result in…
Trailer axle spindles may fracture when subjected to loads exceeding the maximum load recommended.
It IS possible that the wall thickness of the engine mounting pad IS outside of design specifications. If this condition exists, failure of the mounting pad in a bus application could cause the engine to fall to the roadway.
On the involved vehicles, the bolts used to attach the front suspension ball joints to the control arms may fail due to a bolt section crack condition. The ball joint may separate from the arm possibly affecting vehicle directional control.
On the involved vehicles, under a combination of low temperature conditions and a warmed up engine, water vapor in the warm air from the crankcase housing may condense and freeze after a period of steady state driving causing ice build up…
On the involved vehicles, the rear axles may fracture and ultimately allow for a separation of the rear outer ends in the spindle attachment to axle housing area. Such a fracture may also cause the spindle and its components, including the…
The front axle steering arms installed on the suspect vehicles are of a slightly different configuration than those designed for the application. Use of the wrong steering arm presents the potential for improper steering arm to drag link…
The service and parking brakes on the involved vehicles do not conform to federal motor vehicle safety standard no. 121, "air brake systems". Use of the vehicle by individuals not familiar with its braking capabilities may result in longer…
In very cold weather, moisture that enters or may be present in the throttle cable housing may freeze, causing the throttle to stick. Insufficient slack in the throttle cable inside the engine compartment may cause the cable to bend. This…
The control symbols have not been placed in the involved vehicles and the windshield washing system was mis-identified as "accessory". This does not conform to federal motor vehicle safety standard no. 101, "controls and displays". These…
It IS possible that the flywheels in some of the involved engines have cracks located within the pilot bore area. These cracks may progress under operational stresses and lead to fragmentation of the flywheel.
On some of the involved vehicles, the shift rod in the transmission may not be properly seated in the retention grommet of the steering column shift lever assembly. If the shift rod were to disengage, the driver could not select the proper…
The absence of a fastener may allow a flexible rubber brake hose to come into contact with the exhaust manifold. The rubber hose may melt and cause a loss of brake fluid and braking power to the rear axles of the vehicles.
On the involved vehicles, gas leakage between the rubber hose and the furrle nipple may occur due to installation of bad or undersized nipples.
Insufficient hardening of the transmission mainshaft bearing race in some of the vehicles could cause the transmission to lock up during operation of the motorcycle.
Under certain vehicle operating conditions, the governor weight retainer in the injection pump may fail. The throttle valve could stick, preventing return to idle and shut down of the engine by the driver.
The involved tires were inadvertently manufactured with the wrong ply fabric and might cause separation in the tread in the shoulder area. Under this circumstance, the tread of the tire will bulge. This condition will cause a vibration…
The involved tires were inadvertently manufactured with the wrong ply fabric, resulting in separation in the tread in the shoulder area. Under this circumstance, the tread of the tire will bulge. This condition will cause a vibration when…
When the ignition key IS in the "on" position and the heater IS operating at the "low" or "medium" setting, the heater switch wiring will overload in the event the heater motor seizes.
The throttle return springs on the affected vehicles provide less than the required torque, causing a sluggish return of the throttle to the idle position after the accelerator pedal IS released. This fails to comply with the requirements…
The pitman arm retaining bolt may not have been tightened to the required specifications due to a design change. Inadequate retention of the bolt to the output shaft could allow the pitman arm to loosen.
The floorboard opening and the steering column seal bracket may not allow sufficient clearance for the shaft to turn freely in the center of the bracket/seal. The pinch bolt in the column yoke may bind or lock the column against the…
The right hand clearance lamp IS obscured, from certain angles of vision, by the in-line precleaner air cleaner cap. The involved vehicles fail to conform to federal motor vehicle safety standard no. 108, "lamps, reflective devices, and…