Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Metal bushings for the cruise control linkage are subject to corrosion due to weather conditions. Also, there IS not enough clearance between the bushings and the shaft; and the linkage points were not lubricated. Thus…
Looseness may develop at the attachment (ball joint) of the drag link to the steering arm due to an insufficiently tightened retaining nut. This can wear the steering arm hole.…
Impure lubricating grease used in the headlight switches could contaminate one or more contact points. Operation of the headlights could be delayed or not light when the switch IS turned on or when the dimmer switch IS operated.…
Front axle beams contain "shear cracks" at the beam ends where the king pins and steering knuckles are attached. consequence of…
The ply turn up heights around the beads are not to manufacturing specifications. consequence of…
An irregular distribution of rubber gage in the bead area that may in time cause an abnormal stress crack to propagate through the rubber to the ply cords.…
A steel tube that delivers air to the front axle air brake chamber can contact the front shock absorber. consequence of…
Certain trucks do not comply with fmvss 108, "lamps, reflective devices and associated equipment." the trucks were assembled without the roof marker lamps.…
The rack and gear type latch assembly of the emergency doors can be overstressed by misuse of the inside door handle, making the gears subject to failure.…
The hub area of the wheels may not be structurally sound and thus subject to fracture. consequence of…
Seam leaks may develop in the 70 gallon aluminum fuel tank, allowing gasoline to spill on the ground. This IS due to poor seam welding.…
The throttle shaft of the carburetor may crack and eventually break at the threaded hole for the throttle plate connection due to excessive vibration of the throttle shaft.…
The auxiliary fuel tank IS subject to overfill and pressure buildup. consequence of…
A ground fault may occur in the stoplight switch which IS located on the right handlebar in the throttle twist grip housing. consequences of…
The hazard warning flashers fail to meet requirements of the durability test. Devices do not survive the test period or fail flash rate or starting time requirements.…
The saginaw tilt steering column assembly has two pivot bushings and two mating retaining bolts. These retaining bolts can loosen, which could allow the pivot bushings to move into the turning arc of the column shaft universal…
Malfunction after usage which could result in no signal, continuous signal or rapid signal rate. Fail to conform to fmvss 108. consequence of…
Flashers fail to operate in the flashing mode, failure to meet the durability and failure to meet the flash rate requirements of fmvss no. 108.…
The weld attachments of the front spring hanger, on both sides of the trailer, to the trailer frame may break if the running gear of the trailer catches on an obstruction and the operator pulls it free with the tow vehicle.…
Flashers do not comply with flash rate requirements of fmvss no. 108. Malfunction could result in no signal, continuous signal or rapid signal rate.…
Turn signal indicators (flashers) fail to conform to federal motor vehicle safety standard no. 108. The malfunction consists of no signal, continuous signal or rapid signal rate.…
Leakage could occur under combinations of temperature, pressure and vibration extremes when starting or operating the vehicle. consequence of…
The headlamps do not comply with photometric and beam pattern location requirements of fmvss no. 108. consequence of…
The manual steering gear unit may lack integrity due to the heavy use of road salt in certain areas of heavy snow fall. consequence of…
U bolts used to secure the truck body to the chassis may fracture under normal stress. consequence of…
The lp gas distribution system where the lp line passes over the rear suspension leaf spring does not have enough clearance and could allow contact between the lp line and the leaf spring. This could lead to failure of the…
The wood anchor screws holding the inboard end of the furnace may not have been installed. Thus, the furnace may shift position or bounce while traveling.…
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. consequence of…
The flashers do not comply with flash rate, starting time or durability requirements of fmvss no. 108. consequence of…