Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The steering pitman arm could develop cracks and eventually fracture due to high bending loads. consequence of…
Flasher units fail to meet requirement of fmvss no.108, for durability, starting time and flash rate. consequence of…
Missing grommet in two piece truck tube valve. consequence of defect: if the grommet IS missing it will cause a slow air leak around the valve…
The nylon fuel supply and return lines are improperly routed along the frame side rail and could contact the universal joint on the front driveshaft.…
Rims were not labeled as required by fmvss no. 120 . also, tires failed to show strength ratings as required by fmvss no. 119.…
The 12 mm spacer used on the rear seat belt anchorage bolts may affect anchor bolt load capacity and fail to comply with fmvss 210, seat belt assembly anchorages.…
The engine air cleaner plastic trim cover could detach from the air cleaner assembly and fall forward on the exhaust manifold. consequence of…
The stop pin which IS swaged into the throttle lever, so as to allow the throttle lever to absorb excessive throttle linkage travel and maintaining the ability to control the engines speed. This stop pin could be a mismatch and could…
The lead wires connecting the battery to the starter solenoid, and the solenoid to the starter, may be misrouted and damaged. consequence of…
A malfunction may occur in the air suspension electrical circuitry.
Fuel hose may be damaged due to too much pressure in crimping the hose end fitting. consequence of…
Carbon monoxide produced by the auxiliary power generator, when used for prolonged periods of time may enter the motorhome interior.…
The steering arm may crack after repeated full-lock turns. consequence of…
The electrical cable between the starter and the alternator can rub against the brake fluid pipe attached to the left inner wheelhouse in the engine compartment.…
The seat belt may not remain snug after adjustment. consequence of defect: in the event of a sudden stop or accident the seat belts may not…
The welded wedge inside the coupler holds the ball clamp which assures that the ball clamp has a full grip on the towing ball which may not have been sufficiently weled or the wedge may have been omitted in production.…
The fuel system may leak at the throttle body injection fuel feed pipe connection. consequence of…
Circuit breakers are not at sufficient ratings to protect high side tolerances, some wiring harnesses are not adequately secured to prevent chafing and no provisions were made for complete disconnection of all electrical…
Filaments are wired backward so that light from continuously illuminated tail lamps hides the light from intermittent stop lamp signal.…
Hairline cracks may occur in one or more of three weld areas: front suspension interface plate at the bottom frame structure, rear suspension termination points of the transverse link tower outboard gusset, or rear axle mounting…
Front seat belt retractors may not properly lock during sudden heavy brake application or impact due to the interference of two positioning tabs.…
The air brake hose leading to the front axle spring brake chambers may be 1.5 inches shorter than the specified length or are connected to air tanks mislocated up to 1.5 inches.…
The cruise control vacuum solenoid valves may malfunction at any time the engine IS running and the cruise control IS engaged and cause unexpected engine acceleration.…
The tire placard label on the left front door may have been printed with an error which specifies a higher maximum loading than IS allowed.…
Discs which had previously been stamped with part number 27125 for use with wheels having that part number were welded to rims for wheels having part number 27123. The discs used in both wheel assemblies are identical, the…
Incorrect rear dual wheels may have been installed, making the wheels subject to crack. consequence of…
Failure of flasher to meet durability, flash rate and current requirements of fmvss no. 108. consequence of…
The steel wheel rims may crack and break. consequence of defect: broken wheel rims could cause the driver to lose control of the vehicle and…
Brake master cylinders may have improperly anodized internal surfaces causing accelerated wear of a piston seal. consequence of…
One of the three steering gear to frame bolts may not have been tightened to the required specification. consequence of…