Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Improperly installed remote start units can permit remote engine start while the vehicle IS in gear.
Equipment description: axles used as replacement equipment for marmon-herrington all wheel drive conversion kits. also used as original equipment in certain eldorado national buses. an incorrect welding material was used to join the…
Equipment description: aftermarket cruise control units sold by audiovox, moss motors, S&S automotive and warshawsky. these aftermarket cruise control units can accelerate above the intended set speed.
Equipment description: auto throw lap blankets manufactured by sunbeam corporation and sold to wal-mart stores and therm technology corporation. date coded I (1995) or j (1996) production. two circuits were crossed-wired on these throws.
Equipment description: an electronic device for use by physically challenged individuals to steer a motor vehicle. possible unwanted motion at the factory steering wheel can result in a momentary loss of control of the vehicle steering.
Equipment description: braided steel brake lines included with lki enterprises, inc. "Superlift suspensions" brake 4" to 6" lift system. these brake lines are intended for application on 1988 and newer chevrolet, GMC and other gm light…
The bar pin end can fail.
At the taper pin end of the torque rod IS a metal and rubber bushing. this bushing begins to unseat, or "walks-out."
The swing arm of the car rack can prematurely disengage causing the car rack to fall from the vehicle.
If the ignition IS turned on and the fuse for the electronic control module (ecm) power feed line IS removed or burned out, the safety features designed to prevent injury to persons working in the vicinity of the engine will be bypassed…
The compressed natural gas (CNG) cylinder mounting brackets retaining bolts can break.
A metallurgical defect in the axle spindles causes brittleness and possible breakage.
The pin area of the replacement bulb IS not water tight. this does not comply with the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment."
The dimensions of these headlamp bulbs do not comply with fmvss no. 108, "lamps, reflective devices, and associated equipment."
Engine block heaters installed as accessories. the block heater contact surface does not match correctly with the engine block as intended. the block heater could come loose from the engine block, and if being used, could possibly…
Two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
These hose assemblies do not contain the assembler's identification. this does not comply with federal motor vehicle safety standard no. 106, "brake hoses."
A general motors (gm) hose which directs the power steering fluid from the power steering reservoir to the power steering pump required relocation to accommodate the air conditioning compressor. the substitute hose was not compatible for…
A lack of weld penetration attaching the wheel center to the rim.
The "o" rings of the regulator assembly can weaken and break when exposed to high ambient temperatures.
The equalizing beam shaft of the tandem axle suspension were manufactured from as-rolled sae4140 steel rather than the specified annealed sae4140. These shafts can fracture inside the beam at the toe of the weld.
Equipment description: aftermarket ball joint/control arm manufactured by moog industries. due to mispackaging, certain ball joint/control arm assemblies were incorrectly placed in the wrong boxes.
The bushing on the rivet pin IS cracked or missing.
The insulation material between the field effect transistor and ground in the throttle actuator can fail, resulting in an electrical short.
Certain square-shaped "u" bolts used with these lift/lowering kits and lift/lowering blocks can break during installation when torqued to the manufacturer's specifications.
The equalizing beam shaft fractures inside the beam at the toe of the weld.
The seat pedestals are fatigue cracking adjacent to the weld which secures the pedestal's upper plate to the upper, telescoping portion of the adjustable column support.
The seat recliner to seat frame attaching bolts on these vehicles could loosen, fatigue and fracture, allowing the seat back to suddenly recline.
The quick disconnect IS subject to metal fatigue around the bolt holes.
Passenger's clothing can unknowingly become caught in the handrails at bus doors when exiting the bus.