2010 BMW M3
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2010 BMW M3. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2010 BMW M3. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Risk and remedy
Risk
A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy
BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
BMW of North America, LLC (BMW) is recalling certain 2006-2011 323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi and M3, 2007-2011 328i xDrive, 335i xDrive and 335is and 2009-2011 335d vehicles. The wiring and electrical connectors for the system that controls air flow for the heating and air conditioning system may overheat.
Risk and remedy
Risk
Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy
BMW will notify owners, and dealers will replace the wiring and electrical connectors, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Owner complaints
15 complaints1 involved a crash
What owners report most
Latest complaints
- Seat belts · Service brakes · Unknown or other
Parked on a slight hill, shifted out of drive and applied the ebrake by pulling up firmly. Unbucked my seat belt, opened the door, and got out of the vehicle. Left the door open to go in my house, grab my wallet, and come back. The car stayed in neutral instead of shifting into park which should…
Parked on a slight hill, shifted out of drive and applied the ebrake by pulling up firmly. Unbucked my seat belt, opened the door, and got out of the vehicle. Left the door open to go in my house, grab my wallet, and come back. The car stayed in neutral instead of shifting into park which should have happened but multiple components of the car failed to detect me exiting (door latch sendor, software, seat sensor, seat belt sensor). Leaving the car in neutral meant the parking brake was all that was available to hold the car. As it turns out, the electronic brake was not strong enough to do so, and the car rolled down the hill hitting another car, pushing that car into a structure and causing my car to be totaled. This never happened before but due to car not shifting into park with exiting, the vehicle became a rolling hazard putting all people and property around it at risk. I did not hear or see any warning messages as I had exited the car as I had always done previously. I should not have to turn off the car (press power on/off) to engage park or there should be a "park" button like most cars. Given there is no labeled park, the system gives you no indication of what steps you have to take if autopark doesn't engage. My car has been totaled and released to copart. It may be available for inspection from them.
- Air bags
TL* takata recall. The contact owns a 2010 BMW M3. The contact received notification of nhtsa campaign number: 16v071000 (air bags). The parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (BMW of…
TL* takata recall. The contact owns a 2010 BMW M3. The contact received notification of nhtsa campaign number: 16v071000 (air bags). The parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (BMW of dallas, 6200 lemmon ave, dallas, tx 75209 (972) 763-5528) stated that the parts were on backorder. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Engine
Hey my name IS [xxx] , I just recently purchase a used BMW M3 from a BMW dealership on 06/11/17. After a few months of using the car my motor gave a rod knock which IS a common known problem according to the database. I really need help with this situation. This happened to be on the way from…
Hey my name IS [xxx] , I just recently purchase a used BMW M3 from a BMW dealership on 06/11/17. After a few months of using the car my motor gave a rod knock which IS a common known problem according to the database. I really need help with this situation. This happened to be on the way from florida which was 500 miles from my house. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr
- Air bags
Takata recall. Manufacturer still delaying remedy for my vehicle. (It's been a year and a half since the recall) I'm driving the car with life threatening risk everyday in fear. Please enforce replacement remedy asap.
- Engine
Rod bearings failed due to a manufacturer defect. Many BMW M3'S suffer this issue because if the tightness of the engine which leads to oil starvation and metal shavings begin to destroy the engine. The vehicle was in motion, after sitting for a few hours, I start the car to discover a ticking noise in the engine. Upon checking the oil, I have found metal shavings in the oil.
- Electrical system · Exterior lighting
The oem wiring insulation in the headlight housing has flaked off. the bare wires caused an electrical short when I replaced a light bulb. BMW says that the only repair IS to replace the entire housing for $2100. this will need to be done on the other side eventually, as the insulation IS…
The oem wiring insulation in the headlight housing has flaked off. the bare wires caused an electrical short when I replaced a light bulb. BMW says that the only repair IS to replace the entire housing for $2100. this will need to be done on the other side eventually, as the insulation IS deteriorating in that housing as well. I have read online that this IS a common problem in many different models because of the type of wiring that was specified by BMW just does not hold up under higher temperatures. knowing that it will be subject to higher temperatures in the engine compartment IS a design oversight and will lead to dangerous malfunctions when operating the vehicle. it IS just a matter of time.
- Air bags
Takata recall. I received a letter from bmwna in march 2016. more than 6 months later, the parts IS still not available from takata for recall when I call the BMW dealership, I am told I will receive another letter from bmwna when the parts IS available. I am very concern about my safety.
- Air bags
Takata recall BMW notified us in march 2016 that it was doing a recall. since then they have not contacted us. I sent them and email today and got an automated response saying, in essence, they would get to it some time in the future. given the danger and risk involved a six month (and probably much longer) wait for a repair IS unreasonable and inconsisent with the law., please urge them to move forward.
- Air bags
Takata recall want to record and link my vin to me vin: [xxx] [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr
- Air bags
TL* takata recall. The contact owns a 2010 BMW M3. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified…
TL* takata recall. The contact owns a 2010 BMW M3. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the issue. The contact had not experienced a failure. The vin was not provided. updated 12/13/16*lj updated 12/15/16.*jb
- Air bags
Takata recall. I don't want to die by exploding airbag please let me know when parts are available my BMW dealer will not give me any information regarding a fix date. I would like information or get on a list for my dealer to get a repair part.
- Air bags
Takata recall. I was notified of this significant safety recall in march 2016. I have tried to get the airbag replaced by my local BMW dealer who says parts are not available and has no idea when they will be received. I cannot drive my vehicle due to the danger of this airbag defect and am seeking a remedy for the delay in repair.
- Engine · Power train
Loud knocking noise and a ticking noise that whined up when accelerated and slowly whined down when the accelerator IS released. It appears to be bad rod bearing and it occurred within an hour of an oil change at the dealership. According to online forums this IS not an uncommon occurrence.
- Engine
2010 E92 55K miles (88K km) the car IS unmodified. the car has a full service history. the vehicle never tracked - almost all travel during my ownership were highway miles (23K). the cause of the incident was a failure of the number 1 rod bearing. the incident occurred on a wet single lane…
2010 E92 55K miles (88K km) the car IS unmodified. the car has a full service history. the vehicle never tracked - almost all travel during my ownership were highway miles (23K). the cause of the incident was a failure of the number 1 rod bearing. the incident occurred on a wet single lane road in poor weather. I was lucky to avoid an accident when vehicles following me were caught unawares by my unexpected deceleration. The was little opportunity to pull over to the side of the road with safety due to the conditions. I lost power steering and power brakes which made the car more difficult to control.
- Power train · Service brakes, hydraulic
When braking hard and downshifting smg seems to be confused as to what gear you want. Happens mostly when downshifting and braking hard then making a right turn . ## vin passed ## 2010,bmw,m3 ##. *Tr
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10244237Functional noises (squealing/honking) when braking shortly before the vehicle comes to a stop. CAUSE Material-
- 10225126Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
- 10211864The footwell module (FRM) cannot be encoded after replacement.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
- 10170574SERVICE ACTION: N54T ENGINE - INSPECT AND REPLACE INJECTOR(S). The piezo-type fuel injectors may cause a rough running at start-up or rough running while at idle.
- 10163047RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. This Service Information bulletin replaces SI B54 09 07 dated September 2018.
- 10162434Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
- 10162431"Erroneous CC Message "Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"
- 10162426Trunk Lid Intermittently Does Not Open or Latch. Intermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE: The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
- 10162406Power Mirrors and/or Windows are Inoperative. The power windows and/or power mirrors are inoperative. The LED on the headlight switch is flashing. There is a check control message for Windows/Mirrors/ Headlights. There may also be a complaint of water in one or both headlights. One of the following fault codes may be stored: * 9CBD - Communication with stepper motor box left defective * 9CBE - Communication with stepper motor box right defective * 9CC1 - Communication with mirror driver side defective * 9CC2 - Communication with mirror passenger side defective/Right Stepper Motor Controller (SMC) signaling fault * 9CCF - Communication with LIN control defective Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector. CAUSE: Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector.
- 10162404"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
- 10162395N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
- 10160287TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10160244TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10154816In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
- 10153726Takata class action settlement. Customer support program. Front driver side airbag modules.
- 10152314Door Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM door lock status due to voltage variations
- 10151335Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
- 10151255ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
- 10151170N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
- 10151119SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
- 10151115SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
- 10151079SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
- 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
- 10150894?RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. INFORMATION Documents have been developed showing the known correct statuses for all hall sensors and micro switches used to operate the retractable hard top (RHT). This document is intended to act as a supplement to the diagnostic information available in ISTA. Comparing these statuses to the actual statuses of a vehicle with a functional problem may assist in narrowing down which sensor/switch is contributing to the functional problem. For E93, the status request may be found by connecting the car to ISTA and selecting: Control module functions/CTM Convertible top module/Diagnosis Requests ?Sensors/Switches For F33/F83, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 F33 F83 RHT Status.pdf. For I15, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 I15 Top Status.pd
- 10150389Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
- 10150385"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
- 10150381Junction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.
- 10150334"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
- 10150330"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
- 10150329Intermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
- 10150324?SI B51 15 08 Body Equipment October 2012 Technical Service. This Service Information bulletin supersedes SI B51 15 08 dated July 2008. designates changes to this revision SUBJECT Rear Window False Anti-trap Activation. INFORMATION The anti-trap protection feature may be activated when no obstruction is present. This may occur at either one or both of the rear windows. The root cause of the false anti-trap activation may be difficult to determine. The attached diagnosis flowchart has been developed to assist with determining the actual root cause of the failure as well as to help prevent unnecessary part replacements. The root cause is typically either an issue with the window system, or an electrical/software issue. The diagnosis flowchart will help ensure that repairs are only carried out for the system that is most likely at fault. Refer to B511508_Attachment. PARTS INFORMATION Refer to the Electronic Parts Catalog (EPC) for the appropriate parts noted in the diagnostic flowchart. WARRANTY INFORMATION Not applicable.
- 10150265Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
- 10150264"The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding."
- 10150224"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150218N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
Every BMW M3 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.