2008 Dodge Caliber AWD
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Dodge › Caliber AWD › 2008
These records cover every 2008 Dodge Caliber AWD. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Owner complaints
17 complaints1 involved a fire
What owners report most
Latest complaints
- Unknown or other
My 2008 dodge caliber would not pass inspection 2 weeks ago. the rear cross member IS rotted out, the front control arms are also in need of replacement. there was a k frame recall on 2007, 2009, 2010, 2011 & 2012, but not 2008. the car was unsafe to drive and it has ruined my new tires. I…
My 2008 dodge caliber would not pass inspection 2 weeks ago. the rear cross member IS rotted out, the front control arms are also in need of replacement. there was a k frame recall on 2007, 2009, 2010, 2011 & 2012, but not 2008. the car was unsafe to drive and it has ruined my new tires. I drove the car back to my house and parked it. it IS going to cost me $2000 for repairs. my extended warranty expired january of 2018.
- Electrical system · Structure › Body
Coming home from a trip and stopped to put gas in and it was night time and the dash lights would not come on. It happened 3 times now. I do not like driving home with a flashlight. also the other problem we have IS we had. Our oil changed and we're told that the front subframe IS rusting out and the oil pan will need to be replaced soon
- Fuel/propulsion system
When fueling car gas intake cuts off repeatedly. takes at least 10 minutes to put gas in car. happens consistently 7 - 8 months.
- Electrical system
Electronic throttle control picture came on dash as I was trying to start car to leave from my home. car shut off and does the same thing again and again. dont want to run battery down. Car still in garage at home.
- Electrical system · Seats › Front assembly › Seat heater/cooler
TL* the contact owns a 2008 dodge caliber AWD. The contact stated that the wiring in the heated seat failed causing the seats to overheat leaving a hole approximately 7 inches behind the seat. The contact stated the rear of the seat was warm and an abnormal odor was detected. In addition, the…
TL* the contact owns a 2008 dodge caliber AWD. The contact stated that the wiring in the heated seat failed causing the seats to overheat leaving a hole approximately 7 inches behind the seat. The contact stated the rear of the seat was warm and an abnormal odor was detected. In addition, the wiring in the steering column failed causing the wiper blades to fail and the windshield wiper fluid to activate. The vehicle was taken to a dealer where it was confirmed that the main wiring in the steering column failed and the heated pad, wiring, zone, cover, and seat would need to be replaced. The steering column was repaired; however, the overheated seat failure had not been remedied. The manufacturer was not notified of the failure. The failure mileage was approximately 97,000.
- Suspension
While getting a maryland state inspection on a low mileage (56K) garage kept dodge caliber the car failed due both the front and rear subframe had excessive rust, fractures and holes. both the subframes crossmembers will need to be replaced. there IS a recall on the 2007 for this exact issue but it IS not honored on the 2008.
- Electrical system · Fuel/propulsion system · Power train
Car wouldn't start because of defective tipm. I often travel the freeway and was experiencing a brief pause in the fuel systems while trying to accelerate. After research I have found that this IS a common issue with a variety of dodge model cars and feel that this could be very dangerous to the…
Car wouldn't start because of defective tipm. I often travel the freeway and was experiencing a brief pause in the fuel systems while trying to accelerate. After research I have found that this IS a common issue with a variety of dodge model cars and feel that this could be very dangerous to the public in general. I feel the implications that this type of system failure has on these models as well as their safety feature IS numerous. I also quite sure that the company IS well aware of its defects, yet they are doing nothing to protect their consumers. *tr
- Vehicle speed control › Cruise control
TL* the contact owns a 2008 dodge caliber AWD. While driving 70 mph, the cruise control was activated and the vehicle accelerated independently. The contact was not able to deactivate the cruise control. The dealer was unable to diagnose the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The vin was unavailable. The approximate failure mileage was 56,000.
- Power train
Vehicle starting making a sound. Was determined that the transmission was in need of replacement. *tr
- Steering · Suspension
Had to replace the wish bones. And am on my 5 th set if tires since may of 2012. Which are not cheap at $130 a piece for the cheapest. Alignment IS always off and tires have to be pumped every couple months.
- Suspension
Found both lower control arm's worn to a point where the tires had to be replaced also. And the vehicle would not pass nys inspection because of worn ball joints. *js
- Structure › Body › Door
Went to your car on saturday september 7,2013 to open my driver door and it fell off the hinge. Purchase the vehicle last year and it has not been involved in any accident since I've been the owner. Took it back to the dealer and was told not covered under warranty. I'm still making payment on this…
Went to your car on saturday september 7,2013 to open my driver door and it fell off the hinge. Purchase the vehicle last year and it has not been involved in any accident since I've been the owner. Took it back to the dealer and was told not covered under warranty. I'm still making payment on this vehicle and I'm just shocked the hinge would break. I need to report this incident due to the fact that the hinge IS defective and this sort of thing IS not a common incident. *tr
- Electrical system
If it IS 80 degrees or hotter, the automatic locks will not lock/unlock by pushing the button on the driver door or by pushing the button on the key. they will not perform the automatic lock when you first start driving. when this occurs I have no way of opening the hatch because there IS no key…
If it IS 80 degrees or hotter, the automatic locks will not lock/unlock by pushing the button on the driver door or by pushing the button on the key. they will not perform the automatic lock when you first start driving. when this occurs I have no way of opening the hatch because there IS no key hole. I'm afraid this IS a fire hazard. Only happens when it IS hot weather or when I have been driving for a long trip. Has anyone else had this problem? *tr
- Suspension
Front tires prematurely worn out due to both lower control arms and both lower ball joints failing completely. Car has 38K miles and IS garage kept. Had to buy 4 new tires at a cost of $650.00 and now both control arms and ball joints at a cost of $580.00. Vehicle IS not road worthy. This should…
Front tires prematurely worn out due to both lower control arms and both lower ball joints failing completely. Car has 38K miles and IS garage kept. Had to buy 4 new tires at a cost of $650.00 and now both control arms and ball joints at a cost of $580.00. Vehicle IS not road worthy. This should not happen with these low miles. The mechanic said the front wheels were very close to falling off of the car. Can you help? *Tr
- Steering › Linkages › Tie rod assembly · Suspension › Front
Both of the tie rods on my car are completely worn at 36,000 miles. the dealer told me this IS a common problem with dodge calibers - premature failure of tie rods. *Tr
- Tires › Pressure monitoring and regulating systems
Tire sensor monitor broke for no reason on two of my tires. called to get fixed and was told they were an estimated 8,000 on backorder and not sure when they would be coming in. My tire was losing air every 2 days. I feel that this should be a recall. Why are we responsible for paying $100.00 per…
Tire sensor monitor broke for no reason on two of my tires. called to get fixed and was told they were an estimated 8,000 on backorder and not sure when they would be coming in. My tire was losing air every 2 days. I feel that this should be a recall. Why are we responsible for paying $100.00 per sensor to have this fixed when it IS clearly a defect on the manufacturer? Chrysler/dodge needs to fix this and recall the product. *Tr
- Service brakes, hydraulic
I have a 2008 dodge caliber I purchased in september of 2009. I am having a problem with my car stopping when I approach a traffic signal. I have gone right through traffic signals. I was coming off an exit ramp, and it had been snowing. When I applied the brakes the vehicle wouldn't stop, and I almost slid into the side of another vehicle. We both could have been seriously injured. *Tr
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
- 10229181Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
- 10223854Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
- 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10218307Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10191460Valve Body. These may cause over drive cycling.
- 10175743Disinfectant Solution Recommended for COVID-19
- 10175735Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
- 10169249Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
- 10169247Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
- 10169245Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
- 10166537RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
- 10140258Flash: UConnect and Voice Recognition Inoperative This bulletin involves replacing the Hands Free Module (HFM). The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality
- 10139985Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 10139978Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
- 1012900882212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
- 10121927NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
- 10026829Chrysler: lower control arm to crossmember mounting bolts. Vehicles were shipped with front lower control arm to crossmember mounting bolts that may not be tightened to specification.
- 10026764Chrysler\dodge service campaign: see document search button for owner letter. Vehicles may have been inadvertently programmed with software that disabled three engine diagnostic monitors. Without monitors, an improperly operating component may go undetected and result in excessive exhaust emissions. Csc letter was received. 1/23/09.
- 10025384Flash: mil illumination with dtc p0139 or 02270. This bulletin involves selectively erasing and reprogramming the powertrain control module (pcm).
- 10024873Flash: mil illumination with dtc p2173.
- 10024872Flash: idle vibration from a stop with closed throttle.
Every Dodge Caliber AWD model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.