Daimler Trucks North America LLC (DTNA) is recalling certain model year 2014-2015 FCCC S2G, MT45G, and MT55G truck chassis manufactured September 17, 2013, to August 27, 2014. The affected vehicles may be equipped with LPI fuel rails for 6 and 8 liter engines. The propane fuel injectors in these fuel rails may not be properly secured by the retainer clip…
Risk and remedy
Risk
Either condition may result in a propane leak which may cause a stall. Additionally, leaking propane in the presence of an ignition source increases the risk of a fire.
Remedy
DTNA will notify owners, and Daimler Trucks North America authorized service facilities or CleanFuel USA authorized repair facilities will verify the proper installation of the injector retainer clip, and replace any leaking fuel delivery tubes, free of charge. The recall began on November 21, 2014. Owners may contact DTNA customer service at 1-800-547-0712. DTNA's number for this recall is FL-667.
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
10195557SS1033353 FCCC S2G Cab Lean
10181849Joyson Safety Systems letter informing DTNA about Hikone Webbing Investigation. JSS is near completion of an initial investigation regarding data integrity issues at the seatbelt webbing manufacturing facility in Hikone, Japan acquired from Takata in April of 2018.
10181761Freightliner Custom Chassis Service Bulletin for When troubleshooting powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter is the only Daimler-approved tool for troubleshooting vehicle Powernet issues. When troubleshooting powernet issues, use the BCT-460DTNA PowerNet Assessment Tool. As of May 29, 2018, the AutoMeter is the only Daimler-approved tool for troubleshooting vehicle Powernet issues.
10174376Warranty Information Letter for Warranty Training Online. DTNA is pleased to announce the release of new Warranty-related training videos. The videos provide Warranty content in short instructional videos that are available on demand through the AftermarkeTV Video Channel icon on the Aftermarket Resource Center (ARC) home page.
10174061Warranty Policy Letter for Chassis Progressive Damage Policy Change. Effective for repair orders opened on or after April 27, 2020, if an Authorized Service Location installed a part which later has a warrantable failure, progressive damage and labor may be covered under the Aftermarket Parts Limited Parts Warranty (Parts Warranty).
10174060Warranty Policy Letter for Handling for Authorized Service Location Part Transfers. To promote 24-hour throughput and maximum efficiency, DTNA is adjusting multiple handling policies: Launching a new handling allowance for parts ordered from another Authorized Service Location because the facing Part Distribution Center (PDC) is out of stock Retiring Detroit's Customer First Program
10174052Warranty Policy Letter for Handling Change: Over the Counter Aftermarket Parts Replacement Program. DTNA is pleased to announce that handling will increase to 33% for Misc. Replacement Part type claims filed under the Over the Counter (OTC) Aftermarket Parts Replacement Program.
10163625HDEP GHG17 engines are not equipped with turbo wastegates. Steps in this troubleshooting involving wastegates were removed.
10163622The modified parked regeneration strategy has been standard on GHG17 units since the start of GHG17 production and was added to EPA10 and GHG14 units with a software update. The modified regeneration utilizes an improved strategy to clean the DOC inlet face and reduce downtime due to DOC face plugging.
10163620DTNA Special Tools Group has approved the use of Haweka Axis4000 aftermarket alignment system for use on DTNA products at DTNA service locations. The Axis4000 system uses the reference points required by DTNA for precise, accurate, and repeatable measurements. Axis4000 is a sophisticated, user-friendly system that utilizes computer based camera-radio technology and references the center line of the frame for measuring and providing alignment results to DTNA specifications.
10158075FL739 - Interim Recall Notice
10158054FL739 - Interim Recall Notice
10156423FL739 ? Interim Recall Notice
10156402FL739 ? Interim Recall Notice
10154916Service Information Bulletin- Exhaust Gas Recirculation Crossover Pipe
10154915Service Information Bulletin
10154914Service Information Bulletin- Oil Present at the Turbocharger Compressor Housing
10154909FCCC Chassis Rocker Arms and Intake Gaskets SF548 - Termination Date Extended