2016 Fiat 500E

Recalls

1 recall names the 2016 Fiat 500E. Newest first.

• Electrical system › Propulsion system › Traction battery

  May 16, 2016NHTSA 16V30300016,584 vehicles

  Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Fiat 500e vehicles manufactured March 22, 2012, to January 29, 2016. The power inverter module (PIM) may experience voltage spikes which can cause the propulsion system to shut down and loss of motive power.

  Risk and remedy

  Risk

  Loss of motive power can increase the risk of a crash.

  Remedy

  Chrysler will notify owners, and dealers will update the PIM software, free of charge. The recall began on July 5, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S26.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system3
2. Exterior lighting2
3. Power train1

Latest complaints

• Nov 22, 2023CA15,347 mi
  Electrical system · Electrical system › Propulsion system › Traction battery

  The contact owns a 2016 Fiat 500E. The contact stated that the vehicle could not immediately be started. The "Service Electrical System" message was displayed. The vehicle was taken to the local dealer who diagnosed the vehicle and determined that the battery was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure. The failure mileage was 15,347.

• Jun 6, 2023CA26,500 mi
  Exterior lighting › Headlights
  The contact owns a 2018 Fiat 500E. The contact stated that while driving at night, it was discovered that the driver's side headlight was not illuminating. The driver's side light bulb was replaced but would intermittently shut off. Upon inspection, the contact discovered that the driver's side…

  The contact owns a 2018 Fiat 500E. The contact stated that while driving at night, it was discovered that the driver's side headlight was not illuminating. The driver's side light bulb was replaced but would intermittently shut off. Upon inspection, the contact discovered that the driver's side light bulb connector had melted and needed to be replaced. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The failure mileage was 26,500.

• Aug 9, 2018CA21,000 mi
  Exterior lighting

  TL* the contact owns a 2016 fiat 500E. While the vehicle was stationary, the rear driver side brake light malfunctioned. The brake light warning indicator displayed the following message: "right stop light out". The vehicle was not diagnosed or repaired. A dealer and the manufacturer were not made aware of the failure. The failure mileage was 21,000.

• Oct 12, 2016CA120 mi
  Electrical system · Power train

  Car stopped while waiting at intersection for no reason in the middle of the street. Would not restart. After a period of time car started and resumed driving.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10251783Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
• 10248509Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10244356LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
• 10244348Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
• 10243209FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
• 10243208Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
• 10242717Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
• 10239957Water Quality When Mixed With Engine Coolant
• 10236933wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
• 10234420Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
• 10230183No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
• 10230180Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
• 10229572Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 10228988Lithium Ion Batteries BeginningApril 1, 2022, a $5,000 penaltywill be assessed to dealers who return any visually damaged battery to the supplier. Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp
• 10227983If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
• 10225424Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 10225287Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
• 102248991.4L FIRE Service Engine (Normally Aspirated) This engine in this kit will contain one of 8 different production full dress engines, but labeled as component engine 68275870AA or 71AA. The received engine will be configured for use with an automatic transmission, (includes auto transmission adapter plate / flexplate) or manual transmission. (includes flywheel / clutch asm) The received engine will be configured with or without a block heater. If required, dealer to purchase/install the block heater. The included instruction sheet K6855863AB in engine kit 68275870AA is to be followed for all applications that it applies. Please see the sheet for details. In addition to the items detailed in instruction sheet K6855863AB, please read the following below to determine the rework required to install this engine into a 2012- 2018 Fiat 500 (FF) with 1.4L EAB normally aspirated engine: 1) determine which condition exists for the received service engine a) vehicle has a manual transmission, received manual transmission engine. b) vehicle has a manual transmission, received automatic transmission engine. c) vehicle has an automatic transmission, received automatic transmission engine. d) vehicle has an automatic transmission, received manual transmission engine. 2) follow below steps based on condition (a) through (d) above. Condition a) No further rework required, other than ordering/installing a block heater if required. Condition b) Remove flexplate / auto trans adapter plate / auto trans engine mounting bracket / auto trans engine oil dipstick from new service engine. Transfer flywheel / clutch / manual trans engine mounting bracket / manual trans engine oil dipstick from old engine. Order/install block heater if required. Condition c) Identify the automatic transmission adapter plate on the original engine. Looking at the rear of the vehicle engine with adapter plate mounted:
• 10224661Electric Vehicle Control Unit (EVCU) System Enhancements
• 10223855Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
• 10223027Lithium Ion Batteries BeginningApril 1, 2022, a $5,000 penaltywill be assessed to dealers who return any visually damaged battery to the supplier. Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp
• 10221822HVAC Control Panel Illumination Inoperative
• 10221597No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
• 10221594Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
• 10221228WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
• 10221153Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
• 10221152Battery Tester Warranty Code Procedures, Medtronic Update Process
• 10221150Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
• 10221097Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
• 10220644Lithium Ion Batteries BeginningApril 1, 2022, a $5,000 penaltywill be assessed to dealers who return any visually damaged battery to the supplier. Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp
• 10220101Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
• 10220099Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
• 10220098Authentic Mopar Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar Glass.
• 10220097Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
• 10220071wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
• 10219831Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
• 10219830Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
• 102198149-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
• 10219809Speakers: For 2016 speakers issues (all bodies), before replacing this part please contact one of the following people regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~
• 10218310RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Navigation failed message is displayed. Clock not automatically updating to local time. Poor or no connection to cellular network. HVAC temperature out of sync with radio display (KL vehicles). Display goes blank/black. Radio locks up. Some Uconnect App remote commands do not execute with the vehicle.

Every Fiat 500E model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.