Ford Motor Company (Ford) is recalling certain model year 2011-2014 Ford F-59 commercial chassis vehicles manufactured December 17, 2009, to April 30, 2014. Corrosive environments, such as water mixed with road salt, may cause a short circuit between the electrical junction block and the mounting bracket/frame.
Risk and remedy
Risk
A short circuit may result in a fire.
Remedy
Ford will notify owners, and dealers will replace the junction block with an improved design, free of charge. The recall began on July 28, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S11. Note: Since the short may result in a fire whether the vehicle is being operated or not, owners are advised to park affected vehicles outside until they have received the recall remedy.
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
10205024Hazard/Turn signal/Trailer tow lighting - Built on or before 05/29/2015
10183760Some 2011-2015 F-59 Commercial Stripped Chassis vehicles built on or before 5/29/2015 may experience hazard lighting, turn signal operation or trailer tow (TT) lighting that is not functioning properly. Vehicle vibrations may internally damage the relays that control the lighting circuits.
10183758Some 2009-2016 E-Series, F-Super Duty, 2009-2015 F-53 Motorhome and 2011-2015 F-59 Stripped Chassis vehicles equipped with a TorqShift transmission and a transmission built on or before 12/15/2015 may exhibit a MIL with DTCs P0751, P0730 and/or P2700
10164497For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
10160931On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
10155574Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
10144224Certain 2012-2016 Model Year F-450 ? F-750 and F-59 Commercial Stripped Chassis Vehicles Equipped with a 6.8L Engine Camshaft Roller Follower Replacement Coverage
10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
10127405Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
10058636Ford: multiple diagnostic codes: super duty and ecoline equipped with 6.8L engines having malfunction indicator lamp illuminate and unable to determine root cause
10058625Ford: some vehicles transmission will experience, after a cold soak or an extended period with engine off, a 2-3 shift hesitation due to possible hydraulic circuit drain. Model 2013-16 various vehicles.
10057834Ford: no service action IS recommended for this condition. Please use at your discretion. Various 2010-2015 vehicles may experience a turbulence noise, similar to an helicopter noise, at highway speeds when the rear door window(s) or sunroof are open.
10057811Ford: certain 2011-2015 ford f-super duty with 6.7 diesel engines may experience a vibration buzz noise from the diesel fuel conditioning module (dfcm) and/or may 10/1/1 pressure fuel lines w/o diagnostic trouble code poosa.
10055573Ford: a possible intermediate clutch piston lip seal IS worn and can cause an intermediate rough clutch piston bore to slip 1-3 and/or no 2-3 upshift condition. Model 2012-2013 e series, F-450, 550, 53 motorhome, f 59 stripped chassis.
10055312Ford: some model vehicles manual for powertrain control/emission diagnostic (pc/ed) has been updated regarding improved cooling fan circuit due to a lack of air conditioning, a malfunctioning indicator lamp (mil) and overheating.
10053457Ford: on some vehicles, with mytouch, my experience displayed time jumping or audio popping during initial ignition on cycle, or slow navigation calculations, due to amount of data, within size of contact list, creating processing problem for module during key on cycle. Models 2011-2013. No model listed.
10053411Ford: due to loose, missing, modified or damaged ground G400, various malfunction indicator light (mil) dtc's, related to glow plug control module (gpcm), may be exhibit on some diesel equipped trucks. Model years 2011-2013. No models listed.
10053409Ford: on some trucks, the exhaust reductant system or the nox control module would experience various mil dtc's related to glow plug control module (gpcm), due to loose, missing, modified or damaged ground G400. No models listed. Model years 2011-2013.
10053408Ford: on various vehicles with my touch,after any apim programming, replacement or disconnect from front display interface module (fdim), touchscreen calibration must be performed. Model years 2011-2013. No models listed.
10044945Ford: due to instrument cluster (ic) not being installed at time of assembly process, commercial chassis four channel antilock brake system (ABS) module will have diagnostic trouble codes (dtcs) b1596 and u1055.
Every Ford F-59 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.