2008 Infiniti G37
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Infiniti › G37 › 2008
These records cover every 2008 Infiniti G37. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2008 Infiniti G37. Newest first.
Nissan IS recalling 204,361 my 2007-2008 altima, altima hybrid, 350Z, 350Z roadster, my 2008 altima coupe, rogue, my 2009 murano, and infiniti my 2007-2008 G35 sedan, my 2008 G37 coupe and EX35 passenger vehicles equipped with continental automotive systems' occupant classification system (ocs) control units. a varistor in the ocs control unit located in…
Risk and remedy
Risk
This could result in the passenger air bag being suppressed which could fail to provide adequate protection in the event of a crash.
Remedy
Dealers will test the signal between the ocs and acu systems using a special tool to check that it IS functioning as designed. if necessary, the seat cushion (containing ocs hardware) will be replaced with a new one manufactured to specification. the recall began on november 4, 2008. owners may contact nissan at 1-800-647-7261 or infiniti at 1-800-662-6200.
Owner complaints
66 complaints2 involved a crash3 involved a fire
What owners report most
Latest complaints
- Air bags
Three times in the past 4 years, the air bag warning light was triggered when the battery was either disconnected/reconnected or jump started. Each time to re-activate the airbag safety system, I had to send out the air bag control module to have it reset. It is not expensive to do that , but it…
Three times in the past 4 years, the air bag warning light was triggered when the battery was either disconnected/reconnected or jump started. Each time to re-activate the airbag safety system, I had to send out the air bag control module to have it reset. It is not expensive to do that , but it does mean one has to disassemble the center console, remove airbag control module and send it out to be reset. Additionally, during the time that the airbag light is on, my understanding is that the SRS is deactivated, which is obviously a safety hazard.
- Air bags
The contact owns a 2008 Infiniti G37. The contact stated that while driving at various speeds, the air bag warning light flashed intermittently. The vehicle was taken to the dealer, where it was diagnosed, and determined that the Occupant Classification System (OCS) varistor in the front passenger…
The contact owns a 2008 Infiniti G37. The contact stated that while driving at various speeds, the air bag warning light flashed intermittently. The vehicle was taken to the dealer, where it was diagnosed, and determined that the Occupant Classification System (OCS) varistor in the front passenger seat had failed and needed to be replaced. The vehicle was not repaired due to the cost. The contact related the failure to the Manufacturer Recall Number: P8243. The manufacturer was made aware of the failure; however, no assistance was offered. The failure mileage was approximately 140,000.
- Air bags · Seats
According to Campaign P8243, Ref ITB08-045e, NTHTSA # 08-521, my 2008 Infiniti G37 has a warning blinking light for the passenger airbag. I contacted the National Consumer Affairs Dept of Infiniti and they said that my vin # did not indicate it has a recall. I was quoted $5000 to replace the seat by other mechanical shops, but my vehicle is not worth that anymore. Please advise. Thank you.
- Air bags · Electrical system
The airbag control module can be damaged through normal use. Simply disconnecting the battery can damage the module, which then causes the airbag malfunction light on the instrument cluster to turn on. It is unclear weather or not the airbag will function when this occurs. Presumably, it will not.…
The airbag control module can be damaged through normal use. Simply disconnecting the battery can damage the module, which then causes the airbag malfunction light on the instrument cluster to turn on. It is unclear weather or not the airbag will function when this occurs. Presumably, it will not. The dealer solution for this is to replace the module, at a cost of over $1000. Fortunately, it is possible to remove the module and send it to a 3rd party who can reflash a chip. However, doing this every time a random electrical glitch (common ) causes the warning system to trip is dangerous.
- Air bags
Air bag light indicator on dashboard continually flashes off and on…no reason for it to be doing so; i.e., the vehicle has had no impact to cause it to flash.
- Air bags · Forward collision avoidance › Adaptive cruise control
The passenger air bag light is on and flashing and all my controls for my steering wheel have stopped working including my horn!
- Air bags
SRS Air Bag light continues to flash after the vehicle is running. This causes the passenger airbag to stay off even if a passenger is buckled in the seat.
- Electrical system
Regarding tracking number 11400119.- infinity called me today(from phone number 6157257000. She said they are not interested in my case because the car has no recall on it. I'm confused because I thought you and infinity would want to know what caused the fire and if others with this model of.car were in danger of being set on fire.
- Electrical system
Last night while I was sleeping, my car caught fire inside.it appears it started where the seat warmer button is(on the console). It was a big enough fire to reach the roof.
- Power train
After 60K miles, the car has difficulty shifting in reverse. Once in reverse, the car doesn't roll back and it remains idle as if left in park. a foreign transmission repair shop owner said that this issue IS not user error, and that nissan/infiniti have not been having ongoing trans issues with…
After 60K miles, the car has difficulty shifting in reverse. Once in reverse, the car doesn't roll back and it remains idle as if left in park. a foreign transmission repair shop owner said that this issue IS not user error, and that nissan/infiniti have not been having ongoing trans issues with many of their models, but refuse to claim responsibility for most. nissan/infiniti USA will easily goad customers into paying $8K to install a new trans, however.
- Engine
The vehicle has started to stutter upon taking off and shows signs of power loss. After much investigation, these G37S have a minor defect that causes the engines to run on low oil pressure. The part 'gallery gasket' IS the culprit that causes these engines to, in bad cases, last only up to 100K…
The vehicle has started to stutter upon taking off and shows signs of power loss. After much investigation, these G37S have a minor defect that causes the engines to run on low oil pressure. The part 'gallery gasket' IS the culprit that causes these engines to, in bad cases, last only up to 100K miles. Everywhere online there are infiniti owners talking about this gallery gasket problem and few of them have had to buy a replacement engine because of it. Infiniti has failed to come forward with a solution to reduce the amount of oil related problems in these cars. As mentioned, this IS a minor defect with the VQ37 engines but with an outcome that can cost thousands of dollars to either fix or replace. A simple google search of 'G37 gallery gasket' will bring many pages of owners with the exact same problem trying to give each other advice. There are many videos online showing what an owner must go through in order to fix their daily drivers. It would only be right for infiniti to come forward and offer at least free labor to fixing these cars when the symptoms first start. That way owners can keep driving without worrying that their engines will go out due to a bad gallery gasket. The G37 IS very reliable in all other aspects besides the gallery gasket. Owners can only hope that the proper steps are taken in order to avoid the problems the gallery gasket brings.
- Unknown or other
Inside my 2008 G37 coupe, on the passenger side , water IS leaking onto the floorboard. It looks like it's coming from somewhere in the firewall. I've ran my own test and tried to fix it multiple times for 3 years but finally caved in and looking for help. I think its something more than the sunroof drain . What can infiniti do to help me ?
- Air bags · Electrical system
I hit a bump or a pothole in the road and my driver side airbag deployed. My insurance wouldn't cover the claim as there had been no front or rear impact damage. Ever since my cars battery won't hold a charged and had to be jumped off prior to each use.
- Structure › Body
2008 G37 dash IS cracking along the edges. Many other G37 from 2008 to 2010 are having this issues. Its a manufacture problem and should have been recalled long ago. People pay good money for these cars. Dash board caracking IS a sign of cheap material used.
- Air bags · Electrical system · Engine
Around 6AM on 4/13/19 me and my family and neighbors were awoken by an explosion in the front end of my vehicle..we called the fire dept and they ruled it as an electrical problem..i noticed that all the sensor lights in the dash would blink and the airbag sensor light was going off that evening…
Around 6AM on 4/13/19 me and my family and neighbors were awoken by an explosion in the front end of my vehicle..we called the fire dept and they ruled it as an electrical problem..i noticed that all the sensor lights in the dash would blink and the airbag sensor light was going off that evening prior to the incident..i didnt think much of it..i was planning on taking it to a mechanic that morning but it caught on fire..its a total loss.the fire fighters had to cut the hood open in half to get to the fire in the engine compartment..its not fair..i had just bought that car..and I loved my infinity..luckily I wasnt injured or anyone else. The vehicle was parked in the street..i need my car for work , school and on a regular basis. Please help me. *Dt*jb
- Air bags
The passenger airbag light keep blinking like the sensor isn't not working, I did came and ask infiniti dealer if there's any recall and they said no
- Air bags
Air bag sensor suddenly come on. it cost $500 to diagnose that it was "probably" the sensor of the passenger seat. cost to repair estimated at $5000. I see that this IS a more common problem than nissan admits. it should be recalled as others have. Not sure why it hasn't been. the car IS worth…
Air bag sensor suddenly come on. it cost $500 to diagnose that it was "probably" the sensor of the passenger seat. cost to repair estimated at $5000. I see that this IS a more common problem than nissan admits. it should be recalled as others have. Not sure why it hasn't been. the car IS worth less than $10,000. so I'm driving it in an unsafe condition but have no other choice financially. *Dt vin not available *jb
- Visibility/wiper
My garage kept 2008 G37S has a dash that has increasingly become shinier to the point that it has become dangerous to drive during the day when the sun IS out. It IS so reflective that it causes a tremendous glare on my windshield. This seemed to happen progressively over the last few years because…
My garage kept 2008 G37S has a dash that has increasingly become shinier to the point that it has become dangerous to drive during the day when the sun IS out. It IS so reflective that it causes a tremendous glare on my windshield. This seemed to happen progressively over the last few years because when I bought the car 6 years ago it was not an issue. The dash itself IS in one piece with no cracks but it IS tacky like uncured rubber. If you put a fingernail in it lightly, that mark IS now there to stay. This makes it impossible to clean or wipe down the dash due to running the finish. It also makes the inside of the windshield hazy due to what I have to assume IS off gassing of some sort. The blinding glare this dash creates on my windshield has nearly caused me to crash on more than one occasion and has got me wanting to sell the car but I don't want to pass the problem on to anyone else. I paid 28,000 for the car 6 years ago and it was a 48,000 car new with every option possible. The infinity dealership in wichita ks was of no help even though they admitted there were problems with G37'S and many other nissans and infinity of this era ( mid 2000's) where the meterial the dash pad IS made from starts to break down just outside the factory warranty. It's only a matter of time these shiny tacky dashes start causing collisions due to blinding glare.
- Power train · Vehicle speed control · Visibility/wiper
Dashboard has become tacky and highly reflective causing a severe glare when the sun hits it. vehicle surges while coming to a stop. Enough to hit something if you do not have the brake pedal pressed abnormally hard.
- Visibility/wiper
The dash board plastic IS melting and the reflection of the sun makes it very difficult to drive in the direction of the sun at all times.
- Air bags · Electrical system
Airbag light randomly came one. I went into the dealership they said it was a sensor in my passenger seat and that it would cost 5K to replace. I was shocked. That IS a manufactured problem and huge safety issue. I shouldn't have to pay for something like that when I already paid over 30K for the car. Not right.
- Air bags
The airbag light came illuminated. the repair shop traced it to a possible faulty sensor or possibly the passenger seat. The sensor must be ordered from infiniti at a cost of almost $1300.and it might take 10 days to get it. plus $700 in labor. It might not fix it and it could be the seat which…
The airbag light came illuminated. the repair shop traced it to a possible faulty sensor or possibly the passenger seat. The sensor must be ordered from infiniti at a cost of almost $1300.and it might take 10 days to get it. plus $700 in labor. It might not fix it and it could be the seat which would be $5000. this IS half or more of the value of the car. I have noted that this IS a common problem with the 2008-2010 infinit's. I was referenced in the infiniti service bulletin as a known defect but they are not offering any recall or repair compensation. that means that a lot of people are driving around in the older infiniti's without air bags!!
- Unknown or other · Visibility/wiper
The dash of the car IS melting causing a shiny surface that reflects off the windshield causing a visual impairment. the dash IS getting sticky as well and can no longer be cleaned. any rag used sticks to the dash. dash has also become very soft which causes imperfections to occur at the…
The dash of the car IS melting causing a shiny surface that reflects off the windshield causing a visual impairment. the dash IS getting sticky as well and can no longer be cleaned. any rag used sticks to the dash. dash has also become very soft which causes imperfections to occur at the slightest touch. there was a class action lawsuit for this that apparently only covered the state of florida. nissan agreed to replace dash and cover all cost except for $250. this should have been blanket coverage across all nissan/infiniti models affected. I know of other owners with same issue - their dash was made of same material as mine. link to class action lawsuit: https://www.girardgibbs.com/melting-dashboards/
- Structure › Body
Melting dashboard makes the surface sticky and shiny. The sticky surface makes everything stick and impossible to clean. The shiny surface creates a glare problem on the windshield when the sun or light hits. That glare IS a problem because I can't see sometimes while driving and creates a temporary blind spot.
- Vehicle speed control
After the car has been driven for 20 minutes or more, it starts revving on its own. it happens mostly when I am entering my garage. I have to stop, back up, then go forward to get in because I have a side garage. I have to keep my foot on the brake to keep from surging forward. I have also had…
After the car has been driven for 20 minutes or more, it starts revving on its own. it happens mostly when I am entering my garage. I have to stop, back up, then go forward to get in because I have a side garage. I have to keep my foot on the brake to keep from surging forward. I have also had this problem when stopped at a stoplight and have almost hit the car in front of me because it surges forward forcefully. if I cut it off and re-start the engine, it stops surging. I mentioned this to my dealership and he said that if it IS not doing it when I take it in, then they probably cant find out what the problem IS. this has been an issue with my infinity for about one year now.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11002539INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11002537CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001653CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001182WINDOW GLASS WARRANTY INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001179REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 11001177WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10233611ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232646REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232645WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232644WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10208936DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10208930CAN COMMUNICATION NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10207844CAN COMMUNICATION CODES DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192822SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed. When ordering a replacement A/T or control valve, use the Infiniti electronic parts information systems to obtain the correct software program part number See this bulletin for further detail.
- 10192806IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location, ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
- 10192802SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.
- 10192788SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
- 10192728SERVICE INFORMATION The purpose of this bulletin is to give Infiniti dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
- 10192693SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.
- 10192639SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
- 10192598SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
- 10192589SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
- 10192569SERVICE INFORMATION The Body Control Module (BCM) for the Applied Vehicles in this bulletin is now shipped as a blank unit. As with previous BCM replacements, when a blank unit is installed, the configuration process must be performed. See this bulletin for further detail.
- 10192531IF YOU CONFIRM: The clutch pedal on an applied vehicle does not return to its normal (rested) position after being depressed to the floor OR the customer states the clutch pedal on an applied vehicle does not return to its normal (rested) position after being depressed to the floor AND there are no leaks in the clutch hydraulic system. ACTION: Flush (remove) ALL existing clutch hydraulic system fluid, and refill with GT-R R35 Special Brake Fluid (see PARTS INFORMATION). - Use the SERVICE PROCEDURE in this bulletin for proper flush and refill procedure. See this bulletin for further detail.
- 10192514SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
- 10192511SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
- 10192505SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
- 10192475SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
- 10192396SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
- 10192345SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.
- 10192314SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192265SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Infiniti vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
- 10192235Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
- 10192232SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
- 10192219SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
- 10192218If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
- 10192191As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
- 10192188SERVICE INFORMATION The navigation system in the Applied Vehicles of this bulletin has an HDD (Hard Disc Drive) map data storage system. This bulletin contains the information and instructions for updating/upgrading the map data with a new version. See this bulletin for further detail.
- 10192146SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
- 10192126SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
Every Infiniti G37 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.