2002 International 7400
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › 7400 › 2002
These records cover every 2002 International 7400. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2002 International 7400. Newest first.
On certain vehicles equipped with air operated fifth wheel slides and an msva 7-pack accessory controller, the 7-pack can allow water to contaminate its circuit board. this could result in inadvertent operation of the fifth wheel slide control.
Risk and remedy
Risk
If the slide control actuates while the vehicle IS in motion, momentum from the trailer can cause the fifth wheel to slide without input from the driver, which could result in a crash without warning.
Remedy
Dealers will relocate the msva 7-pack to a less water intensive environment. a new msva 7-pack base, that has been improved to prevent water intrusion, and all air accessory solenoids will be installed free of charge. the recall began on august 5, 2005. owners may contact international at 1-800-448-7825.
On certain heavy duty trucks equipped with international dt530, cummins, or caterpillar I-6 engines, the positive battery cable between the batteries and the starter may rub against an electrical ground cable between the starter and frame rail.
Risk and remedy
Risk
This could cause an electrical short and/or fire.
Remedy
Dealers will inspect for any chafing. if there IS no evidence of chafing, a saddle clamp will be installed. if there IS evidence of chafing, the damaged cables will be replaced and the saddle clamp installed. the recall began on august 16, 2004. owners should contact international at 1-800-448-7825.
On certain trucks equipped with dt466 or dt530 1308 style engines and 4X4 or 6X6 capability, the universal joint between the front drive shaft and drive axle could come in contact with the engine oil filter under certain braking conditions.
Risk and remedy
Risk
This could cause a loss of complete engine oil which could result in the engine shutting down and increase the risk of property damage, personal injury, or a crash.
Remedy
Dealers will install a shorter oil filter and adapter. owner notification IS expected to begin april 29, 2004. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact international at 1-800-448-7825.
Certain heavy duty trucks fail to comply with the requirements of federal motor vehicle safety standard no. 104, "windshield wiping and washing systems." due to the design of the windshield washer pump motor circuit, the system's ability to function IS impaired when it IS full of frozen water and the pump motor shaft IS locked or frozen (cannot rotate).
Risk and remedy
Risk
Any resultant reduced visibility could cause a crash.
Remedy
Dealers will install a new 10 amp fuse in place of the 5 amp fuse and a new 10 amp label will be placed over the original 5 amp designation on the fuse panel label. Owner notification began on june 27, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact international at 1-800-448-7825.
On certain heavy duty trucks, the fuel line IS routed too close to a turbo charger outlet/exhaust pipe. if an interference condition occurs between the fuel harness and the exhaust pipe, the fuel line inside the reflective heat wrap could melt due to excessive heat.
Risk and remedy
Risk
The melting of the line could result in immediate engine shut down, increasing the risk of a crash.
Remedy
Dealers will inspect the vehicles for proper routing of the fuel harness. if the harness IS routed near the exhaust system, a new fuel harness will be installed. owner notification began december 27, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact international at 1-800-448-7825.
Owner complaints
1 complaints
What owners report most
Latest complaints
- Engine and engine cooling › Engine › Diesel · Fuel system, diesel
Tl*the contact owns a 2002 international 7400. the contact stated that the vehicle was leaking fuel and oil in the high pressure fuel rail. on september 6, 2006, the vehicle was taken in for service and the repair was performed under warranty. the leak resumed when the warranty expired in july…
Tl*the contact owns a 2002 international 7400. the contact stated that the vehicle was leaking fuel and oil in the high pressure fuel rail. on september 6, 2006, the vehicle was taken in for service and the repair was performed under warranty. the leak resumed when the warranty expired in july of 2007. the failure occurs whenever the engine IS running and IS located directly above the starter near several electrical parts. the speed was unknown. the current mileage was 23,983 and failure mileage was 23,590.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10227455J1939 Data link source address information
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10209487Calculating pulses per mile (speedometer setting); only models equipped with International engines
- 10208431J1939 Data Link Source Address Information
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10204137J1939 Data Link Troubleshooting
- 10204136Dual Drive Cab Throttle Position Harness for APS/IVS throttle pedals; only models with both left hand and right hand drive.
- 10201758Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
- 10200831Cab water leak troubleshooting tips
- 10199915General wheel speed sensor troubleshooting
- 10198708Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- 10189743Suggested alignment target values when performing a vehicle axle alignment
- 10189741Frame Rail Straightness Inspection Procedure
- 10181960Cab Lean Concern
- 10179294Driveline Information Center and Troubleshooting Procedures
- 10179289Repair Procedures for Vehicles Struck by Lightning
- 10177096A/C Refrigerant and Oil Capacities
- 10173025Cleaning and Disinfecting Trucks and Buses
- 10172045J1939 Data Link Troubleshooting
- 10170952Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
- 10169879Key Codes and Key Cutting Information (Not for CV Series)
- 10169867Power Distribution Center (PDC) Replacement; 7000 (Workstar) Model Series with Allison or Manual Transmissions
- 10165643Oil Capacities; All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10163416Suspension Lean Diagnostics; All models
- 10162034J1939 Data Link Source Address Information
- 10156324Driveline Information Center and Troubleshooting Procedures
- 10156305Tool Instruction - BCM Programming Harness
- 10145721A/C Refrigerant and Oil Capacities
- 10145715Engine Oil Capacities All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10145711Radio Diagnostics and Information
Every International 7400 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.