2016 KIA Optima Hybrid

Owner complaints

What owners report most

1. Engine2
2. Power train2
3. Electrical system1
4. Exterior lighting1

Latest complaints

• Oct 21, 2025AZFire
  Electrical system · Engine · Power train
  Dear NHTSA, I am writing to formally report a serious safety incident involving my 2016 Kia Optima Hybrid, which caught fire and was completely destroyed on October 5, 2025. Incident Summary: While driving on a highway at approximately 65 mph, I noticed that the vehicle was not entering Hybrid…

  Dear NHTSA, I am writing to formally report a serious safety incident involving my 2016 Kia Optima Hybrid, which caught fire and was completely destroyed on October 5, 2025. Incident Summary: While driving on a highway at approximately 65 mph, I noticed that the vehicle was not entering Hybrid Mode, which is abnormal for its typical operation. I reduced my speed to 45 mph, then down to 35 mph as I began to observe smoke coming from the vehicle. At no point did the vehicle show signs of overheating, and there was no Check Engine Light until shortly before I was able to safely pull over. Within moments of stopping the vehicle and exiting with my passenger, the vehicle was engulfed in flames and ultimately burned to the ground. Fortunately, both occupants escaped unharmed. The vehicle has been inspected by my insurance provider; however, I have been waiting over two weeks for Kia to inspect the vehicle or provide any official response regarding a possible cause. This delay is concerning, especially given the severity of the incident and the potential safety risk to other drivers. Vehicle Details: Make/Model: 2016 Kia Optima Hybrid VIN: [XXX] Mileage: 54,300 Date of Fire: October 5, 2025 Location: US-60 NONCARD & MP-118 Morristown, AZ I am reporting this incident in hopes that NHTSA will investigate whether this is an isolated case or potentially part of a larger safety defect within this vehicle model or hybrid system. The lack of adequate warning and the total loss due to fire raises serious safety concerns. Please let me know if any additional information or documentation is required to support an investigation. Thank you for your attention to this matter. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

• May 23, 2019CA61,000 mi
  Exterior lighting
  The right passenger headlight won't work I changed the light bulb and it's completely off. At first when I attempted to change the bulb the light flickered and I thought that it might've not been put on all the way or it might've became loose. But then it went completely out causing a road hazard…

  The right passenger headlight won't work I changed the light bulb and it's completely off. At first when I attempted to change the bulb the light flickered and I thought that it might've not been put on all the way or it might've became loose. But then it went completely out causing a road hazard and unsafe to drive as lights are very important. It also has caused me to be pulled over by many police when I shouldn't be going through this or anyone's one else that IS going through the same problem with KIA. This first occurred when I was driving on the highway could've been a bad situation. It could be a bad wiring as I read from other reports but KIA has not done a recall. This situation should be covered by KIA and no one should pay as it IS a safety issue and accidents could occur

• Mar 4, 2019CA38,000 mi
  Engine
  For the 2ND year, my KIA would not start in 32 degree weather in big bear, ca. This IS an annual trip & took my kia.the lights, radio all turn on but the engine will not start. I have to wait until noon for the sun to warm up the car & then it's back to normal. I have taken the car back to the…

  For the 2ND year, my KIA would not start in 32 degree weather in big bear, ca. This IS an annual trip & took my kia.the lights, radio all turn on but the engine will not start. I have to wait until noon for the sun to warm up the car & then it's back to normal. I have taken the car back to the dealership & have been told they cannot find any malfunction & never heard of anyone experience what I have. There are many forums with KIA owners complaining of the same, but cannot get a fix or acknowledgement that the problem exists. It's beyond frustrating when the car has less than 40K miles.

• Dec 5, 2017CA10,000 mi
  Power train
  TL* the contact owns a 2016 KIA optima hybrid. While driving 40 mph, the vehicle stalled and lost power. The vehicle was towed to KIA downtown los angeles (1945 s figueroa st, los angeles, ca 90007) where it was determined that there was an issue with the hybrid system. The dealer replaced the…

  TL* the contact owns a 2016 KIA optima hybrid. While driving 40 mph, the vehicle stalled and lost power. The vehicle was towed to KIA downtown los angeles (1945 s figueroa st, los angeles, ca 90007) where it was determined that there was an issue with the hybrid system. The dealer replaced the transmission, but the failure recurred and the vehicle was towed back to KIA downtown los angeles. The vehicle was not diagnosed or repaired. Additionally, upon starting the vehicle, the check engine indicator illuminated. The vehicle was taken back to KIA downtown los angeles where the dealer stated that some wiring inside the engine failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and offered to potentially replace the vehicle. The approximate failure mileage was 10,000.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Pedestrian alert sounds

  DP22005Opened Jan 27, 2023Closed Aug 7, 2023Recall 22V063000
  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for…

  NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

• Loss of Motive Power

  DP22003Opened Sep 12, 2022Closed Dec 12, 2023
  The National Highway Traffic Safety Administration (NHTSA) received a letter dated July 13, 2022, petitioning the Agency to initiate a safety defect investigation into loss of motive power allegations attributed to oil drain pan assembly failures on certain Hyundai Motor America, Inc. and Kia America, Inc. vehicles…

  The National Highway Traffic Safety Administration (NHTSA) received a letter dated July 13, 2022, petitioning the Agency to initiate a safety defect investigation into loss of motive power allegations attributed to oil drain pan assembly failures on certain Hyundai Motor America, Inc. and Kia America, Inc. vehicles spanning Model Years (MY) 2005-2021. The Petitioners cited examples of complaints indicating that the subject vehicles were experiencing rapid loss of engine oil due to oil drain plug back outs, resulting in loss of motive power and/or catastrophic engine damage. Additional complaints were provided which alleged that the oil drain pans lack sufficient structural integrity and are susceptible to cracking. The petition itself can be reviewed at NHTSA.gov under ODI number 11481745. On September 12, 2022, the Office of Defects Investigation (ODI) opened Defect Petition (DP22-003) to evaluate the Petitioners’ request. The Petitioners have provided additional complaints within four supplemental letters dated January 31, 2023, March 21, 2023, May 23, 2023, and August 4, 2023. ODI’s evaluation included the review and analysis of the complaints and supporting information submitted by the Petitioners, as well as additional complaints submitted directly to NHTSA which referenced either the oil drain plug or a crack in the oil pan. After reviewing the available data, ODI has not identified evidence that would support opening a defect investigation into the oil drain pan assemblies of the subject vehicles. Based on a review of the available information, a loss of motive power resulting from an oil drain plug back out has not occurred between the initial sale of a vehicle and the completion of its first oil change. If during an oil change service, a technician fails to remove the existing drain plug gasket before installing a new gasket, it is likely that a proper seal between the drain plug and the oil pan will not be made. An improper seal between the drain plug and oil pan could lead to the backing out on the drain plug, resulting in the sudden loss of oil while driving. Additionally, the provided examples of oil pan cracks were localized to the immediate vicinity of the oil drain plug and/or appeared to be the result of direct-contact with a tool during servicing.  There is no information to support that a vehicle-based defect exists relating to the oil pan assembly, and instead the documented incidents are related to the failure to follow the proper maintenance procedures during oil change service. In October 2023, Hyundai published a Technical Service Bulletin (TSB) that provided detailed instructions for oil change service on its gasoline powered vehicles, specifically highlighting the need to remove and replace the existing drain plug gasket prior to reinstalling the drain plug. After a thorough review of the material submitted by the petitioner, the information already in NHTSA's possession, and the potential risks to motor vehicle safety implicated by the petitioners' allegations, NHTSA does not believe that a formal investigation is warranted. Therefore, the petition is denied. A Federal Register Notice (FRN) further detailing NHTSA’s reasons for denial of the petition will be published. The reference numbers for the complaints to NHTSA cited by the petitioner can be found in the petition submission documents in the public file for DP22-003. To review those complaints and the additional complaints ODI added to its evaluation which are cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

• Electrical overstress

  EA19001Opened Apr 19, 2019Closed Sep 19, 2024Recall 20V024
  The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect.  During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air…

  The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect.  During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW.  The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications.  The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU.  In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment.  FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle.  Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW.  These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes.  An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time.   In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU.  This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners.  Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW.  The risk associated with the ASIC is equally shared among all OEMS involved in the investigation.  The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage.  There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation.  The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU.  If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC.  Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC.  All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled.  In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024.  With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010705PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2104) - This document is the owner renotification advising that Kia is conducting an important Product Improvement Campaign to perform a software update on 2014-2016 MY Optima Hybrid vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).
• 11010513TECHNICAL SERVICE BULLETIN: PRODUCT IMPROVEMENT CAMPAIGN: SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2104Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2104) titled Knock Sensor Detection System - ECU Logic Improvement for 2014-2016MY Optima (TF HEV) vehicles equipped with Theta 2.4L MPI engine, produced from December 11, 2013 through July 22, 2015. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
• 11006546TECHNICAL SERVICE BULLETIN: VOLUNTARY SERVICE CAMPAIGN: HIGH-VOLTAGE BATTERY SAFETY PLUG FUSE INSPECTION AND REPLACEMENT (SC269) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the High Voltage Battery (HVB) Safety Plug Fuse Assembly or Main Fuse on 2013-2016MY Optima Hybrid (TF HEV) vehicles produced from September 27, 2012 through July 22, 2015. The high-voltage fuse in the subject vehicles may have been replaced with an improper non-OEM aftermarket fuse by third-party repair facilities. A fuse of incorrect capacity may experience a shortened service life, which may result in illumination of the Hybrid System Warning and/or Check Engine Light, followed by a no-start condition. If an improper non-OEM aftermarket fuse is installed, it may fail and result in a fire.
• 11006367VOLUNTARY SERVICE CAMPAIGN: OWNER RENOTIFICATION (SC269) - This document is the owner renotification advising that Kia is conducting a Voluntary Service Campaign to inspect and, if necessary, replace the high-voltage fuse in 2013-2016 MY Optima Hybrid vehicles.
• 11000787This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced.
• 10251445PRODUCT IMPROVEMENT CAMPAIGN: OWNER RENOTIFICATION (PI2104) - This document is the owner renotification advising that Kia is conducting a Product Improvement Campaign to perform a software update on 2014-2016 MY Kia Optima Hybrid vehicles equipped with 2.4-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").
• 10239736VOLUNTARY SERVICE CAMPAIGN: HIGH-VOLTAGE BATTERY SAFETY PLUG FUSE INSPECTION AND REPLACEMENT (SC269) - This bulletin provides information to inspect and, if necessary, replace the High Voltage Battery (HVB) Safety Plug Fuse Assembly or Main Fuse on 2013-2016MY Optima Hybrid (TF HEV) vehicles produced from September 27, 2012 through July 22, 2015. The high-voltage fuse in the subject vehicles may have been replaced with an improper aftermarket fuse by third-party repair facilities. A fuse of incorrect capacity may experience a shortened service life, which may result in illumination of the Hybrid System Warning and/or Check Engine Light, followed by a no-start condition. Furthermore, an improper aftermarket fuse may fail and result in a fire.
• 10239735VOLUNTARY SERVICE CAMPAIGN: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Service Campaign (SC269).
• 10239734VOLUNTARY SERVICE CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Voluntary Service Campaign to ensure that the proper high-voltage fuse is installed on 2013-2016 MY Optima Hybrid vehicles manufactured from September 27, 2012 through July 22, 2015.
• 10239733VOLUNTARY SERVICE CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia is conducting a Voluntary Service Campaign to ensure that the proper high-voltage fuse is installed on 2013-2016 MY Optima Hybrid vehicles manufactured from September 27, 2012 through July 22, 2015.
• 10239732VOLUNTARY SERVICE CAMPAIGN: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is conducting a Voluntary Service Campaign to ensure that the proper high-voltage fuse is installed on 2013-2016 MY Optima Hybrid vehicles manufactured from September 27, 2012 through July 22, 2015.
• 10239721SUBSEQUENT REPAIR ACTION: ENGINE REPLACEMENT INSTRUCTIONS FOR DTC P1326 (PI2104Y/Z) - This bulletin provides information related to the Technical Service Bulletin previously published in (PI2104) titled "Knock Sensor Detection System - ECU Logic Improvement" for 2014-2016MY Optima (TF HEV) vehicles equipped with Theta 2.4L MPI engine, produced from December 11, 2013 through July 22, 2015. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).
• 10238225TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR - ELECTRICAL A/C COMPRESSOR - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding partial repair of the Air Conditioning (A/C) compressor assembly on some 2011MY~ Optima Hybrid (TF HEV, JF HEV/PHEV), 2015MY~ Soul EV (PS EV), 2017MY~ Niro (DE HEV/PHEV/EV), 2022MY~ EV6 (CV), 2021MY~ Sorento (MQ4 HEV/PHEV), 2023MY~ Sportage (NQ5 HEV/PHEV), and 2023MY~ Niro (SG2 EV/HEV/PHEV) vehicles.
• 10230486TECHNICAL SERVICE BULLETIN: HIGH-VOLTAGE BATTERY SAFETY PLUG FUSE INSPECTION AND REPLACEMENT - This bulletin provides information associated with the "Hybrid System Warranty Extension Program" (WTY029) to inspect and, if necessary, replace the High Voltage Battery (HVB) Safety Plug Fuse Assembly or Main Fuse on 2013-2016MY Optima Hybrid (TF HEV) vehicles produced from September 27, 2012 through July 22, 2015.
• 10226555TECHNICAL SERVICE BULLETIN: TRANSMISSION FLUID APPLICATION GUIDE - This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.
• 10222379WARRANTY EXTENSION: OWNER NOTIFICATION - This document is the owner notification advising that Kia is extending the Hybrid System Warranty coverage for the high-voltage battery safety plug fuse in 2013-2016 MY Optima Hybrid vehicles from 10 years / 100,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension addresses, at no cost to you, certain concerns related to the potential failure of the high-voltage battery safety plug fuse.
• 10222377WARRANTY EXTENSION: REIMBURSEMENT FORM - This document is a Reimbursement Request form that was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension program launch.
• 10222376WARRANTY EXTENSION: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the warranty extension (WTY029).
• 10222374WARRANTY EXTENSION: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia America, Inc., is extending the Hybrid System Warranty coverage for the high-voltage battery safety plug fuse in 2013-2016 MY Optima Hybrid vehicles from 10 years / 100,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address certain concerns related to the potential failure of the high-voltage battery safety plug fuse.
• 10222373WARRANTY EXTENSION: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia America, Inc., is extending the Hybrid System Warranty coverage for the high-voltage battery safety plug fuse in 2013-2016 MY Optima Hybrid vehicles from 10 years / 100,000 miles to 15 years / 150,000 miles, whichever comes first, starting from the date the vehicle was first put into service. This warranty extension is to address certain concerns related to the potential failure of the high-voltage battery safety plug fuse.
• 10210264TECHNICAL SERVICE BULLETIN: HIGH-VOLTAGE BATTERY ORDERING AND RETURN PROCEDURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin outlines the ordering and return procedure for high-voltage Lithium-ion batteries equipped on EV/hybrid vehicles (hereafter referred to as "high-voltage batteries" or HVBs).
• 10202226TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.
• 10201529TECHNICAL SERVICE BULLETIN: INFORMATION FOR HEADLAMP CONDENSATION AND MOISTURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.
• 10200535TECHNICAL SERVICE BULLETIN: HIGH-VOLTAGE BATTERY ORDERING AND RETURN PROCEDURE - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin outlines the ordering and return procedure for high-voltage Lithium-ion batteries equipped on EV/hybrid vehicles (hereafter referred to as "high-voltage batteries" or HVBs).
• 10200431SC208_OWNR: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Voluntary Emissions Service Campaign to install an auxiliary evaporative canister in their vehicle to ensure the evaporative canister is not releasing excessive pollutants into the air on some 2011-2016 MY Kia Optima Hybrid vehicles.
• 10200420VOLUNTARY EMISSIONS SERVICE CAMPAIGN: AUXILIARY CANISTER KIT INSTALLATION (SC208) - This bulletin provides the procedure for the installation of an add-on auxiliary canister on some 2011-2016MY Optima (TF HEV) vehicles equipped with 2.4L Theta II engine, produced from February 15, 2011 through July 22, 2015. This is to improve evaporative system performance and ensure compliance with Federal and California emission regulation standards.
• 10200416Sc208_poc: proof of correction card
• 10200415Sc208_stkr: voluntary emissions service campaign completion sticker
• 10200410SC208_QA: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign (SC208).
• 10200397SC208_DPSM: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer Parts and Service Managers that Kia America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2016 MY Kia Optima Hybrid vehicles manufactured from February 15, 2011 through July 22, 2015.
• 10200396SC208_DP: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia America, Inc. is conducting a Voluntary Emissions Service Campaign to install an Auxiliary Canister Kit to improve evaporative system performance on certain 2011-2016 MY Kia Optima Hybrid vehicles manufactured from February 15, 2011 through July 22, 2015.
• 10199208PRODUCT IMPROVEMENT CAMPAIGN: THETA 2.4L MPI - KNOCK SENSOR DETECTION SYSTEM (KSDS) ECU LOGIC IMPROVEMENT (PI2104) - This bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2014-2016MY Optima Hybrid (TF HEV) vehicles equipped with Theta 2.4L MPI engines, produced from December 11, 2013 through July 22, 2015.
• 10199207PRODUCT IMPROVEMENT CAMPAIGN: OWNER NOTIFICATION - This document is the owner notification advising that Kia is conducting a Product Improvement Campaign to perform a software update on 2014-2016 MY Optima Hybrid vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").
• 10199206PRODUCT IMPROVEMENT CAMPAIGN: QUESTION AND ANSWER - This document is the Question and Answer Guide containing the most frequently asked questions regarding the Product Improvement Campaign (PI2104).
• 10199205PRODUCT IMPROVEMENT CAMPAIGN: DEALER PARTS AND SERVICE MANAGER MEMO - This document is the announcement to the dealer principals that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2014-2016 MY Kia Optima Hybrid vehicles equipped with 2.4-liter MPI engines, manufactured from December 11, 2013 through July 22, 2015.
• 10199164PRODUCT IMPROVEMENT CAMPAIGN: DEALER PRINCIPAL MEMO - This document is the announcement to the dealer principals that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2014-2016 MY Kia Optima Hybrid vehicles equipped with 2.4-liter MPI engines, manufactured from December 11, 2013 through July 22, 2015.
• 10197335Optima Hybrid (TF HEV) With DTC B1695 - Lost Communication With E-Comp
• 10195049PIT STOP: A/C DYE FOR E-COMPRESSOR EQUIPPED VEHICLES - This bulletin provides information on the proper non-conductive A/C system leak detection dye to be used in all EV, HEV, and PHEV models equipped with an electric A/C compressor.
• 10189545TECHNICAL SERVICE BULLETIN: PARTIAL REPAIR OF C-MDPS MOTOR, ECU, WORM GEAR AND/OR STEERING COLUMN HOUSING - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.
• 10188137PITSTOP/TECHNICAL OPERATIONS - SMOKE MACHINE NOT TO BE USED FOR EMISSIONS TESTING WITH HEV/PHEV MODELS - This Pitstop provides information to properly test the evaporative emissions system in all Kia 2011MY~ Hybrid (HEV) and Plug-In Hybrid (PHEV) model vehicles. A smoke machine should NEVER be used when testing the evaporative system in a HEV/PHEV model vehicle.

Every KIA Optima Hybrid model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.