2021 Mercedes-Benz AMG GLE53
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › AMG GLE53 › 2021
These records cover every 2021 Mercedes-Benz AMG GLE53. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
16 recalls name the 2021 Mercedes-Benz AMG GLE53. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 GLE 350, 2020-2024 GLE 450, 2020-2023 GLS 580, GLE 580, 2019-2023 GLS 450, 2021-2023 Maybach GLS 600, AMG GLS 63, 2021-2024 AMG GLE 53, AMG GLE 53 Coupe, and AMG GLE 63 S vehicles. A 48-Volt ground connection under the passenger seat may not be secured properly, resulting in the ground…
Risk and remedy
Risk
An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the 48-Volt ground connection as necessary, free of charge. Owner notification letters were mailed on May 3, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024040002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLE350, GLE450, GLS450, GLS580, 2021 AMG GLE53, AMG GLE63, Maybach GLS600, AMG GLS63, and 2020 GLE580 vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain into the passenger compartment.
Risk and remedy
Risk
Water intrusion into the foot wells may cause corrosion and/or short circuits to electrical components, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled and the doors may not unlock, increasing the risk of injury. Also, the engine may not start or may enter a limp-home mode, increasing the risk of a crash.
Remedy
Dealers will inspect and reinstall the air conditioner drain hoses, as necessary, free of charge. Owner notification letters were mailed April 28, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of recall numbers 21V-288 and 19V-587. MBUSA's numbers for this recall are 2023030014 and 15.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE350, GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, and 2021 GLE400e, AMG GLS63, AMG GLE63 S, and Maybach GLS600 vehicles. Due to a manufacturing error, the rear door window trim bars may detach.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed November 1, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, 2021 AMG GLE63, Maybach GLS600 and AMG GLS63 vehicles. A ground cable bolt for the 48V ground connection under the front passenger seat may not be secured properly, which can cause the electrical cable to overheat.
Risk and remedy
Risk
An overheated electrical cable can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the ground cable bolt, as necessary, free of charge. Owner notification letters were mailed July 8, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040017.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLE450 and AMG GLE53 vehicles. In the passenger-side footwell, the ground connection bolts for the electric heater may be improperly tightened.
Risk and remedy
Risk
Loose ground connection bolts on the electric heater may cause the wiring to overheat, increasing the risk of a fire.
Remedy
Dealers will check the electric heater ground connection and repair it as necessary, free of charge. Owner notification letters were mailed January 7, 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 GLE 350, GLE 580, GLS 450, GLS 580, AMG GLE 53, AMG GLE 63 S, and AMG GLS 63 S vehicles. The rear window may be insufficiently bonded to the tailgate, which could allow the rear glass to detach.
Risk and remedy
Risk
Detached rear glass can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the rear window, free of charge. Owner notification letters were mailed December 8, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLS450, GLS580, GLE350, GLE450, AMG C63, and 2021 AMG GLE53 vehicles. The seats may have been assembled incorrectly.
Risk and remedy
Risk
Incorrectly assembled seats may not properly restrain an occupant during a crash, increasing the risk of injury.
Remedy
Dealers will inspect and repair the seats, as necessary, free of charge. Owner notification letters are expected to be mailed December 8, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021110010.
Mercedes-Benz LLC (MBUSA) is recalling certain 2018-2020 C300, 2019-2020 A220, AMG C43, AMG C63, 2020 GLE580, GLB250, 2020-2021 GLE450, GLE350, 2021 AMG GLE63, and AMG GLE53 vehicles. The LED headlights may have been incorrectly adjusted during a vehicle repair. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety…
Risk and remedy
Risk
Incorrectly adjusted headlights may reduce visibility, increasing the risk of a crash.
Remedy
Dealers will replace the LED headlights, free of charge. Interim letters notifying owners of the safety risk were mailed August 13, 2021. A second notice will be sent once the remedy is available. Owner notification letters were mailed January 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 AMG GLE 53, 2020 GLE350, GLE450, GLE580, GLS450, and GLS580 vehicles. The air conditioner drain hoses may have been incorrectly installed, causing water to drain into the passenger compartment.
Risk and remedy
Risk
Water intrusion into the driver and passenger side foot wells may cause corrosion and/or short circuits to electrical components, increasing the risk of fire. In addition, the emergency call (eCall) feature may be disabled and the doors may not unlock, increasing the risk of injury. Also, the engine may not start or may enter a limp-home mode, increasing the risk of a crash.
Remedy
Dealers will inspect and correct the air conditioner drain hoses, as necessary, free of charge. Owner notification letters were mailed June 4, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040024.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLS 450, GLE 350, GLE 450, and 2021 AMG GLE53 vehicles. The dashboard surface may not be properly secured to the base material.
Risk and remedy
Risk
In the event of a crash where the passenger air bag deploys, an unsecured dashboard could impair the inflation of the passenger air bag, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the dashboard, free of charge. The recall began April 16, 2021. Owners may contact MBUSA customer serviced at 1-800-367-6372. MBUSA's number for this recall is 2021030003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz AG USA, LLC. (MBUSA) is recalling certain 2021 AMG GLE53, AMG GLE63, 2020 GLE580, 2020-2021 GLE350 and GLE450 vehicles with 5 passenger seating. While buckling the seat belt, the middle seat belt buckle could be pushed down into the gap below the seat cushion. If the buckle can't be retrieved, the buckle latch will be inoperable and unable…
Risk and remedy
Risk
An unrestrained occupant has an increased risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will secure the middle seat belt buckle, free of charge. The recall began December 18, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020110005.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 CLA250, CLA250 4MATIC and CLA35 AMG 4MATIC, 2020-2021 GLE350, GLE350 4MATIC, GLE450 4MATIC, GLS450 4MATIC and GLS580 4MATIC and 2021 GLE53 AMG Coupe, GLE63S AMG 4MATIC, GLS63 AMG 4MATIC and Maybach GLS600 4MATIC vehicles. The instrument cluster software may deactivate the illumination of certain…
Risk and remedy
Risk
If the interior switches are not illuminated, they may be more difficult to find and operate, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the instrument cluster software, free of charge. The recall began March 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020030019.
Owner complaints
16 complaints
What owners report most
Latest complaints
- Unknown or other
An authorized dealer returned a vehicle with loose hardware in a moving mechanical track, posing a risk of mechanical failure or distraction while driving.
- Power train
According to the dealer, there are fault codes in the system for Transmission control unit failing. Thats what caused the vehicle to go into "limp" mode... That needs to be replaced. In an instant, the warning lights and reduction in power occurred simultaneously. The car slowed down and had to…
According to the dealer, there are fault codes in the system for Transmission control unit failing. Thats what caused the vehicle to go into "limp" mode... That needs to be replaced. In an instant, the warning lights and reduction in power occurred simultaneously. The car slowed down and had to coast to shoulder of the highway crossing multiple lanes of traffic. The warnings that came on said “car cannot shift”, “battery failure warning” and when stopped; “do not restart the car.” The shoulder was very narrow and we could have easily been hit by the cars passing at high speeds on the beltway. We had to wait 2 hours for Mercedes roadside assistance to arrive. The dealer is saying it will be $6,000 to repair this.
- Electrical system
Engine harness wires insulation is falling apart very early after 3 years. It’s causing arching inside the insulation. Issues is from overheating and can cause a fire. Isolation needs to be upgraded and wire harness needs replaced.
- Electrical system · Fuel/propulsion system
Vehicle unexpectedly lost power on a major highway. Limped into a service station, called for a tow truck. Several days later vehicle was repaired with a bill of $2800. Four weeks later, while driving, check engine light comes on. Contact dealership that completed repairs, brought car in. Now it’s…
Vehicle unexpectedly lost power on a major highway. Limped into a service station, called for a tow truck. Several days later vehicle was repaired with a bill of $2800. Four weeks later, while driving, check engine light comes on. Contact dealership that completed repairs, brought car in. Now it’s the 48V Hybrid battery needs to be replaced, $4000. Based on some cursory research, this is a known problem in these cars. Mercedes Benz needs to be held accountable. The car was purchased brand new three years ago.
- Electrical system · Engine · Vehicle speed control
Purchased as a CPO directly from a local dealership. Vehicle has experienced multiple (10+), seemingly random failures of the Electronic Stability Control, Blind Spot Assist, Lane Keeping Assist and Active Break Assist under varied driving and weather conditions. On two separate occasions (one at…
Purchased as a CPO directly from a local dealership. Vehicle has experienced multiple (10+), seemingly random failures of the Electronic Stability Control, Blind Spot Assist, Lane Keeping Assist and Active Break Assist under varied driving and weather conditions. On two separate occasions (one at 15+ mph and the other at 65+), these system failures were accompanied by a brief "limp mode" and immediate total loss of acceleration. The most recent loss-of-acceleration event occurred during lunch hour traffic on the highway, at highway speeds. The vehicle has been taken to the dealership to address these issues on 3 separate occasions. Visit #1: the communication fault codes were noted by the technicians, but they could not replicate the issues. The faults were cleared and the vehicle service was deemed complete. Visit #2 (3 days later and the first instance of acceleration loss): report from service department reads almost identical to that of Visit #1 except the notation that "...found several stored faults for communication with engine control unit." Again, the issues could not be replicated and the faults were cleared. Viewed as an unacceptable response by the consumer, the dealership retained the vehicle for further troubleshooting with the follow-on report noting, "Found no socket tension at Sockets 27 and 28 to PTCU. Removed and replaced sockets 27 and 28 at ME connector 6." The faults were, again, cleared and the vehicle was returned to the owner. Visit #3 (roughly 5 weeks after last visit and the second instance of acceleration loss, this time on the highway): The same complement of warning lamps illuminated, the car lurched, and there was zero acceleration. The vehicle was navigated to the highway's shoulder without incident and shut down. After 5+ minutes, the vehicle was restarted and acceleration functioning had returned. It was immediately driven to the dealership where it currently awaits repair.
- Electrical system
We bought this GLE AMG 63 new, it has only 1100 miles and we have had two 48 V batters replaced; they just towed it again to the dealer 22 March because it needs yet another 48V battery; the techs say it’s a design problem but there is nothing they can do except get “approval” to have the 48V…
We bought this GLE AMG 63 new, it has only 1100 miles and we have had two 48 V batters replaced; they just towed it again to the dealer 22 March because it needs yet another 48V battery; the techs say it’s a design problem but there is nothing they can do except get “approval” to have the 48V battery replaced. It has also shut down while driving causing us to pull over on freeway; We don’t five it (1100 miles) because we are concerned about safety issues from the 48V battery failing at unexpected times; firs, overheating and battery coolant issues…etc. We believe this falls under the Lemon law and should be recalled. Thank you for your time and I look forward to your feedback.
- Fuel/propulsion system · Unknown or other
When vehicle is driven 70 mph and above the drive side of vehicle is making a whilst noise by ear of the driver, that is coming into the car. The gas cap door is not sitting flush with the body of the vehicle.
- Tires
The contact owns a 2021 Mercedes-Benz GLE53 equipped with Continental Tires, Tire Line: Sport Contact, Tire Size: 255/40/ZR21, DOT: (Unavailable). The contact stated that on several occasions while driving 30 MPH on wet pavement at low speeds, the vehicle started to shake, and a loud abnormal sound…
The contact owns a 2021 Mercedes-Benz GLE53 equipped with Continental Tires, Tire Line: Sport Contact, Tire Size: 255/40/ZR21, DOT: (Unavailable). The contact stated that on several occasions while driving 30 MPH on wet pavement at low speeds, the vehicle started to shake, and a loud abnormal sound was heard in all four tires. No warning light was illuminated. The vehicle was taken to the dealer where it was diagnosed that the tire assembly needed to be replaced; however, there was no repair for the failure. The manufacturer was notified of the failure and the contact was advised to call the NHTSA Hotline. The failure mileage was approximately 18,000.
- Electrical system · Engine · Unknown or other
2021 MB GLE 53 AMG Coupe. Less than 7500 miles. Car wont start throws a red error saying see the operators manual. This is the second time in 5 months this has happened and is extremely frustrating given MB is fully aware of the issue. They say it is related to software but I just had my car at the…
2021 MB GLE 53 AMG Coupe. Less than 7500 miles. Car wont start throws a red error saying see the operators manual. This is the second time in 5 months this has happened and is extremely frustrating given MB is fully aware of the issue. They say it is related to software but I just had my car at the dealer for another issue and all software was updated. This is a design flaw that MB needs to fix before someone dies. The issue can happen at any time, I have just been lucky enough that both times it was parked in my garage. I am now considering pursuing a full refund under lemon law, I no longer feel safe driving this car and each time it has been in the dealer for repair I am without a vehicle for 2 weeks. Very disappointing for a vehicle that cost almost 100k.
- Unknown or other
Unknown
- Electrical system
In the middle of driving it down the road when - without warning -- the instrument panel went black, the entire panel. My husband was on his way to the dealership to replace a tire when this happened. Though he was able to make his way to the dealer, we consider this event to be a serious safety…
In the middle of driving it down the road when - without warning -- the instrument panel went black, the entire panel. My husband was on his way to the dealership to replace a tire when this happened. Though he was able to make his way to the dealer, we consider this event to be a serious safety issue, given that there was a partial power outage involving the components the driver relies upon to drive the car - for example, the driver's side instrument panel has indicator lights for the odometer, gas & oil levels and especially, the gear shift controls. My husband asked the dealer to look into the problem and was told a 10682 Electrical test was performed showing that the Head Unit had a fault. When tested again it showed no fault & no available software updates, so they cleared the Head codes and ran the test, which came up negative.
- Electrical system · Engine
It is incredibly distressing to have experienced an issue that is widely reported in this database and online forums, and remains unaddressed by MBUSA. It also seems to be an entirely preventable issue that can be fixed via a software update. The issue relates to a malfunction of the 48V battery…
It is incredibly distressing to have experienced an issue that is widely reported in this database and online forums, and remains unaddressed by MBUSA. It also seems to be an entirely preventable issue that can be fixed via a software update. The issue relates to a malfunction of the 48V battery that made the vehicle inoperatable. It happened in the midst of winter and we would be been in a dire position if our family did not come to the rescue to pick us up. The vehicle had to be towed to a dealership. Here is the dealer summary: 48v software vehicle has no power, connected jumper, battery lights on in dash, towed into shop and connected battery charger, performed quick test, found codes in 48v- B183349 and B183371 , referred to Topic # LI54.10-P-069698 remedy #2, performed guided test for B1833349, as per guided test updated 48v software and commissioned, after completion vehicle started normally, performed extended test drive and multiple short test drives to verify vehicle now operating as designed again, lights no longer present in dash.
- Electrical system · Engine
GLE53 would not start. The car threw an error stating 12v battery malfunction.(Impacted the 48V battery) This essentially disables the vehicle completely. This is 2021 GLE53 with less than 5000 miles. There is also an issue with the side-view mirror and wind noise.
- Forward collision avoidance › Adaptive cruise control · Service brakes · Vehicle speed control
Issue-The car brakes aggressively using cruise control (Mercedes Distronic) with no driver intervention. This dangerous condition can cause an accident. Using my advanced cruise control…the issue is my set speed was changed along with acceleration or braking when a traffic sign is misread. I have…
Issue-The car brakes aggressively using cruise control (Mercedes Distronic) with no driver intervention. This dangerous condition can cause an accident. Using my advanced cruise control…the issue is my set speed was changed along with acceleration or braking when a traffic sign is misread. I have turned off the only setting controls Traffic Sign Assist & Route Based Speed Assist but there is no change. Example of issue-My car was misreading 80mph as 60 & braking aggressively. .My prior 2020 GLE misread signs less often and did not change the speed setting or brake the vehicle. The Dealer applied all available software updates. After all the updates my car continues to adjust set speed to every misread traffic sign. For example recently I had my speed set at the posted speed of 80 and the car read a sign as 70, changed the 80 to 70, and started braking aggressively. In Idaho there are stacked signs-the upper one reads 80 and below “Trucks 70” so this happens about 50% of the time. The vehicle misreads signs often.
- Power train
The contact owns a 2021 Mercedes-Benz AMG GLE53. The contact stated that while the gear shifter was in PARK, the vehicle was still rolling. In addition, the vehicle failed to stay in reverse and in neutral. The contact mentioned that the parking brake was activated to keep the vehicle from rolling…
The contact owns a 2021 Mercedes-Benz AMG GLE53. The contact stated that while the gear shifter was in PARK, the vehicle was still rolling. In addition, the vehicle failed to stay in reverse and in neutral. The contact mentioned that the parking brake was activated to keep the vehicle from rolling away. The vehicle was taken to the dealer where they informed the contact that the vehicle was operating as designed. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was unknown.
- Electrical system · Electrical system › Adas › Driver monitoring › Camera/sensor
The contact owns a 2021 Mercedes-Benz GLE53. The contact stated the vehicle would not start. The contact stated that he was unable to jumpstart the vehicle. The vehicle was towed to the dealer who diagnosed that the battery needed to be replaced. The vehicle was repaired. The contact also stated…
The contact owns a 2021 Mercedes-Benz GLE53. The contact stated the vehicle would not start. The contact stated that he was unable to jumpstart the vehicle. The vehicle was towed to the dealer who diagnosed that the battery needed to be replaced. The vehicle was repaired. The contact also stated while driving the vehicle would misread speed limit signs on the road and would shift gears on inadvertently. The dealer was made aware of the failure. The manufacturer was not made aware of the failure. The vehicle was not repaired. The approximate failure mileage was 4,800.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010744Complaint Engine cooling fan running for an extended time after switching off vehicle. Cause Optimized thermal management in latest PTCU software. Remedy This is a normal function in the latest PTCU software. Engine fan will operate for up to 20 minutes after ignition is switched off. Note: Repair work should only be performed if a clear malfunction is identified
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010450Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: E504.5 (A 297 904 09 01)
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11010437Complaint Automatic window raising function of side window inoperative. Cause Denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). This requires the door control unit (N69/x) to be commissioned. (Path: XENTRY -> Control units view -> DCU-XX (N69/x) -> Adaptations -> Commissioning) SW item numbers of the repair software: A1679023716 for the door control units on the front doors (N69/1 and N69/2) A1679023816 for the door control units on the rear doors (N69/3 and N69/4)
- 11010435Complaint -Check engine light(MIL) is ON. -Current and stored fault code in DCCU and PTCU : P2E9873 The position sensor of the exterior socket flap of the vehicle socket (direct current) has an electrical fault. The actuator does not open. -Starting the vehicle or Charging the vehicle is normal without any issues. Cause Software in the "N116/5 - Direct current charge connection unit (DCCU)" control unit. Remedy SW remedy for N116/5(DC-Charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5 For this issue, the vehicle starting or charging functions are not typically affected. Do not replace any parts. Replacing parts will not bring a solution for this issue.
- 11009550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11008882Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008072Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007956Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2023 CLS (257 platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
- 11007858Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.
- 11007857Complaint Customer concern of Air Conditioning not cooling. Note: For vehicles produced during or prior to June 2023, a TIPS case is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. ALL steps, with the exception of videos, should be documented and uploaded with the claim submission. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. "NO TIPS case needed on vehicles during or prior to June 2023"
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11006695Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed. Note: A remedy is not yet available. Replacing the hardware does not resolve the symptom. Do not replace the MBUX for this concern. The information will be updated accordingly as soon as a remedy is available.
- 11006678Complaint Head-up display permanently or sporadically unavailable - with warning message in driver display Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.
- 11006550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11005347Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy If other fault codes related to engine fan are present, process these first. Replace engine fan with part as specified in XENTRY parts information. Group 50/015. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003211Complaint The following event codes are logged in control unit IDC213 - N62/4 (Intelligent Drive control unit): U0401FC and U0401FD. Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.
- 11000618Customer concern of Air Conditioning not cooling. Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000610Complaint 1. Cracking noises from the area of the rear axle 2. or a message in the instrument cluster "ESP, ABS failed". Cause Anti-cracking disk at the external joint of the side shaft at the rear axle is broken. Remedy Customer complaint due to noises: A test drive must be performed. For a precise noise analysis (localization of the noise), make use of the NVH/PICO. If the joint of the side shaft can be clearly identified as the cause (source of the noise), the following work must be performed: 1. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 2. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Customer complaint due to display message "ESP, ABS failed" in the instrument cluster: Read out the fault memory; if a rotational speed sensor of the rear axle is stored in the fault memory, the following work must be performed: 1. Check the rotational speed sensor of the affected side for damage and replace if necessary. 2. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 3. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Note: It is not necessary to replace the side shaft.
Every Mercedes-Benz AMG GLE53 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.