2022 Mercedes-Benz AMG GLE53
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › AMG GLE53 › 2022
These records cover every 2022 Mercedes-Benz AMG GLE53. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2022 Mercedes-Benz AMG GLE53. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 GLE 350, 2020-2024 GLE 450, 2020-2023 GLS 580, GLE 580, 2019-2023 GLS 450, 2021-2023 Maybach GLS 600, AMG GLS 63, 2021-2024 AMG GLE 53, AMG GLE 53 Coupe, and AMG GLE 63 S vehicles. A 48-Volt ground connection under the passenger seat may not be secured properly, resulting in the ground…
Risk and remedy
Risk
An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the 48-Volt ground connection as necessary, free of charge. Owner notification letters were mailed on May 3, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024040002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2024 GLE, GLS, C-Class, E-Class, S-Class, SL, GLC, CLS, AMG GT, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, causing a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 28, 2024. Owner notification letters will be mailed in phases, on February 23, 2024, April 19, 2024, June 28, 2024, August 9, 2024, October 1, 2024, and December 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 23V-445.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 GLE350, GLE450, GLE580, GLS450, GLS580, Maybach GLS600, AMG GLE53, AMG GLE63 S, and AMG GLS63 vehicles. The rear door window trim bars may detach from the vehicle while driving.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed May 5, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of previous recall number 22V-680. MBUSA's number for this recall is 2023040011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 GLE350, GLE450, 2022 AMG GLE53, AMG GLE63, and GLS450 vehicles. The steering coupling locking screw may loosen and possibly detach from the steering gear, resulting in a loss of steering control.
Risk and remedy
Risk
A loss of steering control can increase the risk of a crash.
Remedy
Dealers will replace the steering coupling locking screw, free of charge. Owner notification letters were mailed January 27, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022120016.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE350, GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, and 2021 GLE400e, AMG GLS63, AMG GLE63 S, and Maybach GLS600 vehicles. Due to a manufacturing error, the rear door window trim bars may detach.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed November 1, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, 2021 AMG GLE63, Maybach GLS600 and AMG GLS63 vehicles. A ground cable bolt for the 48V ground connection under the front passenger seat may not be secured properly, which can cause the electrical cable to overheat.
Risk and remedy
Risk
An overheated electrical cable can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the ground cable bolt, as necessary, free of charge. Owner notification letters were mailed July 8, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040017.
Owner complaints
13 complaints
What owners report most
Latest complaints
- Structure › Body
The panoramic sunroof exploded upwards and outwards while driving under normal conditions. It created an extremely loud and startling sound that left the driver and passenger stunned. We were fortunate there was not an immediate oncoming vehicle as we likely would have struck head on. Shortly after…
The panoramic sunroof exploded upwards and outwards while driving under normal conditions. It created an extremely loud and startling sound that left the driver and passenger stunned. We were fortunate there was not an immediate oncoming vehicle as we likely would have struck head on. Shortly after the explosion, tiny shards of glass began to fall into the passenger area. We were also fortunate to be able to get the vehicle safely off the road. The vehicle was brought to the dealership and the manufacturer was called. They are all pretending they have never heard of something like that happening when a quick search reveals this is a known manufacturing defect with a class action lawsuit filed. The named plaintiff is actually a customer from the very dealership we brought the vehicle to for service. There is no chance they are not aware of the problem.
- Engine
Vehicle has issues maintaining power and attempts to stall in traffic. It also shakes violently at idle. It was diagnosed by the dealership and determined that the cylinder head was damaged and needed to be replaced for $7200.00 since there was no warranty. Vehicle was purchased used and the Issue…
Vehicle has issues maintaining power and attempts to stall in traffic. It also shakes violently at idle. It was diagnosed by the dealership and determined that the cylinder head was damaged and needed to be replaced for $7200.00 since there was no warranty. Vehicle was purchased used and the Issue was noticed 6 months after purchase at 70-80 thousand miles. After researching the issue, this appears to be a known problem with the 4 cylinder Mercedes vehicles, but only specific models were covered under the extended warranty for replacement.
- Engine · Fuel/propulsion system · Unknown or other
Nov. 7, 2025 - After returning home around 4pm, I parked the car in my garage, and entered my home. Due to the sound of the fan motor which stays on after you shut off the car, it is possible that the engine was still running when I thought it was off. Please note that my garage is attached to my…
Nov. 7, 2025 - After returning home around 4pm, I parked the car in my garage, and entered my home. Due to the sound of the fan motor which stays on after you shut off the car, it is possible that the engine was still running when I thought it was off. Please note that my garage is attached to my home. Around 1am I awoke and went into the bedroom on the far side of my home which sits directly above my garage. When I entered this room I heard a noise, like some kind of motor but at the time I had no idea what this was. As I walked through my home, went downstairs and neared the doorway to my garage when I realized the loud noise was coming from my garage. It was not only frightening but extremely concerning and come to find out my Mercedes was running, in fact it had been running since I got home earlier in the afternoon. Please note that one of the most critical things that happened is that upon opening the door to the garage I was exposed to severe carbon monoxide fumes. I discovered the car sitting there, running, for no reason at all, the outside was very hot to the touch and I panicked. I was breathing in fumes that could affect my life! I ran to the kitchen, grabbed a fan, opened the garage doors and immediately went upstairs to see if my daughter was okay. As you know carbon monoxide can kill you and I did not know why in HECK this was happening. - This car is still relatively new with low miles. - This vehicle is also supposed to be equipped with significant safety features and it is difficult to exit the car without alarms sounding and appearing on the dash telling you the car is still on. - Mercedes, however, already made me take this car in twice to address multiple recalls affecting safety! I also had it serviced not less than 3 weeks ago. - Mercedes is completely skirting/ignoring the critical issues with this vehicle and has sent me a FORM letter denying assistance. There could have been 2 fatalities and I have been ill since this happened.
- Steering · Suspension
The contact owns a 2022 Mercedes-Benz AMG GLE53. The contact stated while driving at various speeds, the vehicle started swaying from left to right. There were no warning lights illuminated. The contact stated that while her husband was driving, the vehicle was swaying from side to side. The…
The contact owns a 2022 Mercedes-Benz AMG GLE53. The contact stated while driving at various speeds, the vehicle started swaying from left to right. There were no warning lights illuminated. The contact stated that while her husband was driving, the vehicle was swaying from side to side. The contact stated that the tires were previously replaced; however, the failure recurred. The vehicle was taken to the local dealer who was unable to determine the cause of the failure. The vehicle was test driven and the contact was informed that the vehicle seemed to be top-heavy. The vehicle was not repaired. The manufacturer was contacted but no assistance was provided. The failure mileage was approximately 6,000.
- Fuel system, gasoline
The contact owns a 2022 Mercedes-Benz GLE53. The contact received notification of NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall…
The contact owns a 2022 Mercedes-Benz GLE53. The contact received notification of NHTSA Campaign Number: 23V445000 (Fuel System, Gasoline) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
- Electrical system · Engine · Fuel/propulsion system
On March 30, 2023, my 2022 AMG GLE 53 check engine warning light came on. I immediately called Capitaleurocars the Mercedes Benz dealer. On May 1, 2023, according to the Capitaleurocars service order, the technician noted the following: "found the check engine light on" then performed "a guided…
On March 30, 2023, my 2022 AMG GLE 53 check engine warning light came on. I immediately called Capitaleurocars the Mercedes Benz dealer. On May 1, 2023, according to the Capitaleurocars service order, the technician noted the following: "found the check engine light on" then performed "a guided test for fault code (P146264) and found fuel pressure and temp sensor passing test." The technician wrote "Checked PTSS cases and checked for related LI documents. Found LI-47.50-p-070263 which states that software is under development for this issue. no software available at this time. Cleared code and released back to customer." Capitaleurocars service department could not tell me when the software update would be issued, but I would be notified as soon as it was released. I was also told that on September 6, 2022, a temperature sensor was replaced on the vehicle due to the check engine warning light being on. I asked if the issue on September 6, 2022, was the same issue I was having and I was told yes, it was the same fault code. So, approximately a month before I purchased the car on October 1, 2022, the check engine warning light was on and a temperature sensor was replaced. The Capitaleurocars service department suggested I call MBUSA Customer Service to get more information about the software update. I researched the LI document number and found that NHTSA had received a complaint on 06/25.2020, with same the LI 47.50-p-070263 document number and fault code P146264. The complaint to NHTSA was on a GLE and noted as follows: Complaint: Check engine light active and FC P146264 Temp. and pressure sensor B4/7 is stored in engine control unit and tank control unit. Cause: Software parameter in Fuel pump control unit Remedy: Update SW in FSCU control unit Capitaleurocars Service Department did confirmed that the fault code found on my car on May 1, 2023, was the same as the one reported to NHTSA on 06/25/2020.
- Tires
I purchased the vechile brand new in July from North Olmsted Mercedes. I purchased winter tires in Oct they were installed in Nov. I stored the Yokohama in my finished basement 68-70degress on carpet. Upon installation this spring Mercedes refused due to seperation & dry cracking. They have less then 4000 miles on them. 325-35ZR22
- Tires
Tires were purchased with car in July of 2022. Winter tires were purchased and installed in Nov. These tires were stored in my basement- finished on carpet at 68-70dgrees. When pulled out for installation mercedes refused due to seperation & dry cracking 325-35ZR22
- Tires
I purchased my vehicle brand new in July 2022 with these tires. I purchased winter tires in Oct they were installed in Nov. The Yokohama was stored in my finished carpeted basement. They were brought up to be installed & they are showing thread seperation & dry cracking with less then 4000 miles on the tire.
- Tires
Tires purchased in July 2022 with car new from Mercedes of North Olmsted. I purchased winter tires in Oct & they were installed in Nov. Yokohama tires were stored in my finished basement at a nice 70degrees. When taking them to be put on they are showing signs of thread separation & dry cracking. They only have 4000 miles on them. 285-40ZR22
- Engine
Radiator failed after driving on the highway. Radiator failed due to an item passing through the grille in the normal course of driving causing coolant to leak from car. Low coolant warning light indicated that coolant was low. Car was inspected by dealer who determined that an external…
Radiator failed after driving on the highway. Radiator failed due to an item passing through the grille in the normal course of driving causing coolant to leak from car. Low coolant warning light indicated that coolant was low. Car was inspected by dealer who determined that an external influence(road debris or a small rock) passed through the front car grille and striked the radiator causing the radiator failure. Manufacturer was notified of the incident regarding the radiator failure.
- Electrical system · Engine
1. 48 volt battery electrical system malfunctioned. car shut down on the road while driving. 2. could have been rear ended if on highway and there was no shoulder 3. dealer had car for a week and serviced electrical components and updated software. 4. no police. vehicle serviced ny manufacturer…
1. 48 volt battery electrical system malfunctioned. car shut down on the road while driving. 2. could have been rear ended if on highway and there was no shoulder 3. dealer had car for a week and serviced electrical components and updated software. 4. no police. vehicle serviced ny manufacturer 5. eceived many warning notices when it happened - 48 volt battery , coolant too hot, engine overheating, etc. no prior warnings. first occurrence 1/4/2023, second occurrence 2/21/2023 issue reocurred
- Forward collision avoidance › Adaptive cruise control · Lane departure › Assist · Steering
While driving with Active Cruise Control (Distronic) and with Lane Keep Assist off and Active Lane Change Assist off, the car would forcefully and suddenly try and steer me back into my lane while performing a lane change while using the blinker. It happens randomly and abruptly. Most lane changes occur without issue and there are no obstructions or other warnings that occur during these incidences.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010744Complaint Engine cooling fan running for an extended time after switching off vehicle. Cause Optimized thermal management in latest PTCU software. Remedy This is a normal function in the latest PTCU software. Engine fan will operate for up to 20 minutes after ignition is switched off. Note: Repair work should only be performed if a clear malfunction is identified
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010450Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: E504.5 (A 297 904 09 01)
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11010437Complaint Automatic window raising function of side window inoperative. Cause Denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). This requires the door control unit (N69/x) to be commissioned. (Path: XENTRY -> Control units view -> DCU-XX (N69/x) -> Adaptations -> Commissioning) SW item numbers of the repair software: A1679023716 for the door control units on the front doors (N69/1 and N69/2) A1679023816 for the door control units on the rear doors (N69/3 and N69/4)
- 11010435Complaint -Check engine light(MIL) is ON. -Current and stored fault code in DCCU and PTCU : P2E9873 The position sensor of the exterior socket flap of the vehicle socket (direct current) has an electrical fault. The actuator does not open. -Starting the vehicle or Charging the vehicle is normal without any issues. Cause Software in the "N116/5 - Direct current charge connection unit (DCCU)" control unit. Remedy SW remedy for N116/5(DC-Charging control unit box) is in progress. Once the software is available, update the software for N116/5 and perform SCN coding of N116/5 For this issue, the vehicle starting or charging functions are not typically affected. Do not replace any parts. Replacing parts will not bring a solution for this issue.
- 11009550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11008882Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008072Complaint White plastic insert present on microphone assembly. See figure A for example. Cause The insert (breathable filter) is designed to be inside for dust protection and air flow control. Remedy Do not remove the breathable filter from the microphone assembly. This part is designed to be in the microphone and should remain in the vehicle. Note: If TIPS support is required for microphone symptoms please open a TIPS case and reference this LI.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007956Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2023 CLS (257 platform), E-Class (213 and 238 platform), GLE (167 platform), and AMG GT 4-Door (290 platform) vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software.
- 11007858Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.
- 11007857Complaint Customer concern of Air Conditioning not cooling. Note: For vehicles produced during or prior to June 2023, a TIPS case is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. ALL steps, with the exception of videos, should be documented and uploaded with the claim submission. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. "NO TIPS case needed on vehicles during or prior to June 2023"
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11006695Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed. Note: A remedy is not yet available. Replacing the hardware does not resolve the symptom. Do not replace the MBUX for this concern. The information will be updated accordingly as soon as a remedy is available.
- 11006678Complaint Head-up display permanently or sporadically unavailable - with warning message in driver display Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.
- 11006550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11005347Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy If other fault codes related to engine fan are present, process these first. Replace engine fan with part as specified in XENTRY parts information. Group 50/015. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003211Complaint The following event codes are logged in control unit IDC213 - N62/4 (Intelligent Drive control unit): U0401FC and U0401FD. Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.
- 11000618Customer concern of Air Conditioning not cooling. Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000610Complaint 1. Cracking noises from the area of the rear axle 2. or a message in the instrument cluster "ESP, ABS failed". Cause Anti-cracking disk at the external joint of the side shaft at the rear axle is broken. Remedy Customer complaint due to noises: A test drive must be performed. For a precise noise analysis (localization of the noise), make use of the NVH/PICO. If the joint of the side shaft can be clearly identified as the cause (source of the noise), the following work must be performed: 1. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 2. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Customer complaint due to display message "ESP, ABS failed" in the instrument cluster: Read out the fault memory; if a rotational speed sensor of the rear axle is stored in the fault memory, the following work must be performed: 1. Check the rotational speed sensor of the affected side for damage and replace if necessary. 2. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 3. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Note: It is not necessary to replace the side shaft.
- 11000606Complaint Message in Instrument Cluster: "Active Brake Assist function restricted". The driver assistance systems are temporarily unavailable. Note: Please note the listed fault code! Cause Rarely, it may be the case that communication is interrupted due to a brief interruption in the power supply to the LRR (B92/12) or A108 (Active Brake Assist). Remedy Perform new SCN coding at BC_R (N10/8).
Every Mercedes-Benz AMG GLE53 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.