2018 Mercedes-Benz AMG GLE63

Recalls

5 recalls name the 2018 Mercedes-Benz AMG GLE63. Newest first.

• Structure › Body › Roof and pillars

  Dec 15, 2023NHTSA 23V8540002,976 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…

  Risk and remedy

  Risk

  A detached roof panel can become a road hazard, increasing the risk of a crash.

  Remedy

  Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.

  Full recall details →

• Fuel system, diesel › Delivery › Fuel pump › Control/drive module

  Dec 23, 2022NHTSA 22V955000348,183 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…

  Risk and remedy

  Risk

  An engine stall while driving increases the risk of a crash.

  Remedy

  Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.

  Full recall details →

• Structure › Body › Roof and pillars

  Mar 19, 2021NHTSA 21V19700015,096 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…

  Risk and remedy

  Risk

  The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.

  Remedy

  Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Communication › Auto crash notification

  Feb 5, 2021NHTSA 21V0580001,292,258 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…

  Risk and remedy

  Risk

  Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.

  Remedy

  MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.

  Full recall details →

• Service brakes, hydraulic

  Aug 16, 2018NHTSA 18V5390009,044 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018 Mercedes-Benz GLE350 4Matic, GLE350, GLS450 4Matic, GLS550 4matic, GLE43 AMG 4Matic, GLE63 AMG 4Matic, GLE63S AMG 4Matic, and GLS63 AMG 4Matic vehicles. The rear brake caliper pistons on these vehicles may not have been correctly coated, causing gas to become temporarily released into the rear brake…

  Risk and remedy

  Risk

  Reduced braking performance can increase the risk of a crash.

  Remedy

  MBUSA will notify owners, and dealers will bleed the rear axle brake system, free of charge. The recall began September 14, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018080013.

  Full recall details →

Owner complaints

Latest complaints

• Apr 3, 2019NY8,000 mi
  Service brakes

  I got 9000 miles on my 2018 mercedes benz GLE AMG 63S coupe I am going for my second set of breaks

• Dec 17, 2018MA
  Service brakes

  Brakes need replacing after only 11 months old and 14,000 miles. Loud squealing from brakes upon applying them. This has been a problem since purchasing the car in jan. 2018. Reported to dealership multiple times and was told it was normal. Now they want me to pay to have the brakes replaced.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Front Roof Panel Detachment

  PE21001Opened Jan 8, 2021Closed Oct 14, 2021Recall 21V197000
  On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…

  On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
• 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10241527Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customers vehicle. The OTA may be validated as successful on the customers Mercedes Me connect app under Over-the-Air Vehicle Updates as Update for the communication module. If the OTA is successful it will show a green installed and date of installation in the Over-the-Air update section.
• 10219259Complaint CEL on with Code P012800 "The Coolant Temperature is Below the Specified Temperature" Cause Under investigation. This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy Due to formatting issues please see "remedy instructions" in attachments
• 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
• 10205835Model series 167 noise on B/C/D pillars.
• 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
• 10189402Complaint: Height adjustment of electric steering column adjustment jams in upper / lower adjustment position or it generates a cracking noise when exiting the upper /lower adjustment position (e.g. for Easy Entry function). Cause: Height adjustment runs into upper / lower limit stop and jams there or generates a breakaway cracking noise when exiting the jammed limit stop. Remedy: 1. Move fore/aft adjustment to the end position. 2. Release jamming of height adjustment by knocking with palm of hand onto top of steering wheel. At the same time, push adjusting switch (downwards). 3. Commission driver's seat control unit. While doing so, - the control unit software is updated, if necessary - the limit stops are cleared and normalized again - and any renewed jamming is prevented 4. Once commissioning has been completed the vehicle can be handed over to the customer.
• 10184798Replace charge air hose between charge air cooler and turbocharger
• 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
• 10172683Information Label on Tire Sealant
• 10169590MY17+ M157 Equipped GLE63, GLS63, G63 ECOStop/ Start: Engine May Not Automatically Restart
• 10167785G-Class Facelift 2018: Fault message "ABS, ESP inoperative, see operator's manual"
• 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
• 10167565A flapping/rattling noise can be heard from the area of the center console towards the rear.
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
• 10167549Thumping noises at the front axle when driving over road bumps

Every Mercedes-Benz AMG GLE63 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.