2012 Mercedes-Benz C250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C250 › 2012
These records cover every 2012 Mercedes-Benz C250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2012 Mercedes-Benz C250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.
Risk and remedy
Risk
An incorrect air bag may not function properly in a crash, increasing the risk of injury.
Remedy
Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012 C250, C250 Coupe, C300, C350, C350 Coupe, C63 AMG, and C63 AMG Coupe vehicles equipped with a front passenger air bag assembly replaced under a prior recall. An incorrect replacement front passenger air bag may have been installed.
Risk and remedy
Risk
An incorrect passenger air bag may not provide adequate protection, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began July 10, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida…
Risk and remedy
Risk
An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691
Owner complaints
272 complaints3 involved a crash2 involved a fire3 injuries
What owners report most
Latest complaints
- Service brakes · Steering · Vehicle speed control
-The steering wheel and brake locked up and became unusable while driving at approximately 75mph. Cruise control was enabled for a few miles (maybe 2) and disabled after. Around 5 minutes after disabling, the car began to surge between acceleration and deceleration drastically on its own. All of…
-The steering wheel and brake locked up and became unusable while driving at approximately 75mph. Cruise control was enabled for a few miles (maybe 2) and disabled after. Around 5 minutes after disabling, the car began to surge between acceleration and deceleration drastically on its own. All of the dashboard lights that come on when the key is initially inserted came on at once while engine was on/running and the car was in drive. After finally being able to reach a safe enough spot, I put the car in park and turned the engine off. I sat for a few minutes to try and turn the engine/car back on and the car would not crank, but the overhead lights, radio, and dash lights were functioning. -This was an extremely dangerous experience. The car began to decelerate rapidly in heavy freeway traffic. At that speed, with many semi-trucks traveling nearby, this sudden loss of speed created an extremely dangerous situation. My vehicle instantly became a slow moving obstacle in the lane. Only by luck and quick reaction was a serious or fatal collision avoided. The car would not start back up so I was sitting at the edge of the highway as many cars flew by just inches away from my car. -I am away at college in a rural city. Accessibility is limited as well as support because of lack of resources. -The car was towed to a mechanic who does not specialize in German cars and stated they did not have the proper tools to "get into the car" because the motor is "locked up" and the car wouldn't crank. -The vehicle will be towed to the nearest dealership (50mi away) who stated they won't be able to look at it for a few weeks from date of arrival. Research indicates this may be linked to a known issue with Electronic Steering Lock (ESL) / Electronic Ignition Switch (EIS) failure in Mercedes vehicles, which can electronically disable the engine and steering. This could've easily been fatal for me and still poses an alarming threat if not addressed.
- Engine
The contact owns a 2012 Mercedes-Benz C250. The contact stated that while driving at an undisclosed speed, there was an abnormal rattling sound coming from the vehicle with the check engine warning light illuminated. The contact drove the vehicle to the shoulder of the road. The contact stated that…
The contact owns a 2012 Mercedes-Benz C250. The contact stated that while driving at an undisclosed speed, there was an abnormal rattling sound coming from the vehicle with the check engine warning light illuminated. The contact drove the vehicle to the shoulder of the road. The contact stated that the rattling sound continued, and the vehicle shuddered abnormally. The vehicle was towed to the residence. The independent mechanic provided mobile service and diagnosed the vehicle with cam shaft timing chain adjuster failure. The contact was informed that the cam shaft timing chain adjuster needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 150,000.
- Service brakes, hydraulic
The contact owns a 2012 Mercedes-Benz C250. The contact stated while driving 35-40 MPH and depressing the brake pedal, the brake pedal was significantly stiff, and the vehicle failed to respond as needed. The contact stated that upon standing on the brake pedal, the vehicle responded as needed. The…
The contact owns a 2012 Mercedes-Benz C250. The contact stated while driving 35-40 MPH and depressing the brake pedal, the brake pedal was significantly stiff, and the vehicle failed to respond as needed. The contact stated that upon standing on the brake pedal, the vehicle responded as needed. The contact stated that the failure recurred while driving 65 MPH. The vehicle was taken to the dealer, where the vacuum pump was replaced; however, the failure recurred. The vehicle was taken to Mercedes-Benz of Beaumont (1865 I-10 S, Beaumont, TX 77701), where it was test-driven, and the dealer became aware that the brake pedal was extremely firm. The dealer diagnosed the vehicle and determined that the vacuum pump needed to be replaced. The part was replaced; however, the failure persisted. The contact stated that the failure increased, causing the contact to engage the parking brake to stop the vehicle. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 96,826.
- Air bags · Engine · Power train
The model/year Mercedes-Benz are well known for experiencing this/these particular issues. My research has shown that these year/make/model vehicles are experiencing the same type of mechanical failures nationwide. The issues all relatively begin around 75,000 miles. I've only had my car 3 years…
The model/year Mercedes-Benz are well known for experiencing this/these particular issues. My research has shown that these year/make/model vehicles are experiencing the same type of mechanical failures nationwide. The issues all relatively begin around 75,000 miles. I've only had my car 3 years putting 30000 on it hardly driven/cared for **Issue Found:** Oil was leaking onto the ignition coil and spark plug of cylinder 3. **Source of Leak:** Valve cover gasket failure. **Recommended Repairs:** - Replace the valve cover gasket (to halt the oil leak). - Replace spark plugs and ignition coil (which were contaminated/damaged by oil). **Relevance to Warranty:** The valve cover gasket is only covered if it fails as a result of an internally lubricated engine part causing damage. Ignition coils and spark plugs are maintenance items and are not covered by warranty plans. **Required Repairs (Identified Mechanical Issues)** - **Coolant Pipe Leak – $850** **Issue:** Coolant leaking from a pipe on the side of the cylinder head. **Relevance to Warranty:** Typically not covered unless it pertains to a failure in a covered system such as the water pump or cylinder head due to an internal breakdown. This is likely classified as an external plumbing component, which is not included. - **Oil Feed Line Leak – $600** **Issue:** Oil leaking from the side of the engine, traced back to the oil feed line. **Relevance to Warranty:** This is not typically covered unless the oil feed line is part of the oil pump system and has failed due to an internal issue (usually regarded as an external line). **Other Items Found (Worsening Issues)** - **Timing Chain Rattle / Cam Adjuster Noise – $6,000** -**Issue:** Rattling sound during startup. **Diagnosis:** Noise emanating from the timing chain and camshaft adjusters. **Relevance to Warranty:** This is covered under Secure Plus, as both the timing chain and camshaft adjusters are recognized as internally lubricated par
- Engine · Fuel/propulsion system
The contact owns a 2012 Mercedes-Benz. The contact stated while driving at an undisclosed speed, the Check Engine and High Pressure Fuel Pump warning lights was illuminated. The failure occurred on several different occasions. The vehicle was taken back to the residence. The contact did research…
The contact owns a 2012 Mercedes-Benz. The contact stated while driving at an undisclosed speed, the Check Engine and High Pressure Fuel Pump warning lights was illuminated. The failure occurred on several different occasions. The vehicle was taken back to the residence. The contact did research and was made aware of an unknown NHTSA Campaign Number however, the VIN was not included. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
- Power train · Service brakes · Steering
Lost of drive power and the vehicle steering wheel locked on my mercedes from a damaged malfunctioning steering lock actuator module due to mechanical issues within the steering column such as bad steering wheel assembly, faulty steering lock module or issue with the wiring or other electrical…
Lost of drive power and the vehicle steering wheel locked on my mercedes from a damaged malfunctioning steering lock actuator module due to mechanical issues within the steering column such as bad steering wheel assembly, faulty steering lock module or issue with the wiring or other electrical components and the mercedes dealer is the only one who solves this issue no other mechanic in general. My safety was at risk due to I lost power and lost of front brakes due to bad sway bar assembly or components could of caused and accident when this happened on November 12, 2024 the problem dealership found during vehicle inspection was code 25464 they told me recommend to replace electric lock module and repair estimate was $2,829.78 and before I approved the the amount I told Mr Ivan Velasco service advisor that after they replace the module that if my vehicle was going to be working again and that if I was just going to make 1 payment of $2,829.78 then I would approved it so I did. Weeks later I got an email asking for more money they wanted another payment for $600 saying it needed a sensor that has something to do with the transmission because after replacing the new module the vehicle did not start up there was no type of communications nothing at all and I responded that I was not going to pay $600 more just cause they don't know what their doing because they promise me the car was going to work after they replace the module now that it did not want to crank up they found another issue that's their fault on not doing there job the right way and for telling lies yes their was flashing blue or red icon on my dashboard that look like a car and a lock would go on and off and it displayed a message saying The theft protection is activated. I want to know if I can get this issue approved and to be considered a recall can you please help I'm so frustrating and mad that they want more money when it's already so expensive please help I would of appreciate it thank you.
- Electrical system · Engine · Unknown or other
1. The car radio, blue-tooth, speakers, sound, car remote sound. Happened after a battery change by AAA - unsure if it's related. CUstomer service tried to resolve it - radio turns on, but nothing else works. 2. Doors won't unlock outside or inside - except passenegers side is open. 3. Accelerator acting strange - won't pick speed after 30, then 60 4. there was an air bag recal of this car a while ago.
- Electrical system › Ignition › Interlock/lockout
The contact owns a 2012 Mercedes-Benz C250. The contact stated while the vehicle was parked, the anti-lock theft prevention feature failed to function as intended. The contact stated that the steering wheel was seized, and the vehicle failed to start. The vehicle was towed to the residence. The…
The contact owns a 2012 Mercedes-Benz C250. The contact stated while the vehicle was parked, the anti-lock theft prevention feature failed to function as intended. The contact stated that the steering wheel was seized, and the vehicle failed to start. The vehicle was towed to the residence. The contact was informed by the tow truck driver that the failure was due to the electronic lockout system. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 143,000.
- Engine
My vehicle, has the engine making noise ,when starting,, the lifters rattle...i was told to check with mercedes benz for recall info...however, the company states,this vehicle IS not included....it has 52,000 original miles, and has been maintained...i believe, this problem should be covered by the…
My vehicle, has the engine making noise ,when starting,, the lifters rattle...i was told to check with mercedes benz for recall info...however, the company states,this vehicle IS not included....it has 52,000 original miles, and has been maintained...i believe, this problem should be covered by the manufacturer...please advise.....i have had the mb dealer do a diagnosis..they confirm the lifters are disfunctioning....
- Lane departure › Assist · Lane departure › Blind spot detection · Steering
I got stranded in the middle of the street my vehicle does not crank steering lock so I had my vehicle towed into the Mercedes dealership the one in Figueroa st Monday November 18 2024 at around 03:24pm and this is what they told me. Needs immediate attention custom recommendation ELECTRIC…
I got stranded in the middle of the street my vehicle does not crank steering lock so I had my vehicle towed into the Mercedes dealership the one in Figueroa st Monday November 18 2024 at around 03:24pm and this is what they told me. Needs immediate attention custom recommendation ELECTRIC STEERING LOCK During vehicle inspection found electric steering lock has malfunction code 25464 recommend to replace electric steering lock first and perform re-check. Repair total estimate: $2,829.78 I definitely can't afford to pay that amount please help with this issue
- Seats
Active headrest on front passenger seat forcefully deployed without any collision or impact occurring. It happened during a gradual stop at red light. Bits of broken plastic were found on the passenger seat after deployment. Cannot re-set the headrest because of broken parts. No one was in the seat at the time but now concerned that the same thing will happen to driver's headrest.
- Fuel/propulsion system
During hard acceleration the high-pressure fuel pump fails. I've never had to replace this part on any other car that I have owned. When I research the part for this car, I reviewed many forums and articles complaining about the failure of the high-pressure fuel pump on the Mercedes c250 sport or…
During hard acceleration the high-pressure fuel pump fails. I've never had to replace this part on any other car that I have owned. When I research the part for this car, I reviewed many forums and articles complaining about the failure of the high-pressure fuel pump on the Mercedes c250 sport or similar chassis. The vehicle performs normally until there is hard acceleration; then the engine light comes on. This causes the car to lose acceleration power and slows the car down significant and can be dangerous especially if driving on a freeway or highway. The failure of the part has been reported to occur as early as 30k miles.
- Engine
What component or system failed or malfunctioned, and is it available for inspection upon request? As I started my car from a cold start and even when starting the engine, the car was creating this tractor like sound. No system has failed but I read the camshaft adjuster and tensioner pulley has…
What component or system failed or malfunctioned, and is it available for inspection upon request? As I started my car from a cold start and even when starting the engine, the car was creating this tractor like sound. No system has failed but I read the camshaft adjuster and tensioner pulley has come out of site, which can ruin the engine. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes, it was audible by the dealer but I was told that it would be a normal issue on a cold start. Now they will charge $200 for a service diagnosis. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Mercedes Benz gave an extended warranty on the program for extension of 10 years but the problem has been happening for multiple people and it has been happening again that this warrants a recall over a poorly designed part that can destroy the car’s engine. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? No such codes or messages. Which is why this is so scary. This incident has been happening for the past 8 months or so and besides a letter about a warranty no such information.
- Air bags · Electrical system · Engine
1) cranshaft and camshaft position sensors, timing problems and it has to be replaced this is a common damage in Mercedes Benz 2012 c250. 2) this put in risk my life because it can brake the engine in a highway and the car could be off.
- Fuel/propulsion system
While trying to pass big rig on freeway my car went into lymph mode and stalled causing the car behind me to brake and almost caused an accident. My engine light came on & after getting it checked out I retrieve the following code P0002. After doing some research it appears this is an ongoing issue with this year and model of car.
- Unknown or other
Dear Sir/Madam, I am writing to file a formal complaint against the Fletcher Jones Mercedes-Benz franchise located in Ontario, California and Mercedes-Benz USA , specifically addressing the issue of the dealership closing the recalls and not honoring the warranty recall on my 2012 Mercedes C250…
Dear Sir/Madam, I am writing to file a formal complaint against the Fletcher Jones Mercedes-Benz franchise located in Ontario, California and Mercedes-Benz USA , specifically addressing the issue of the dealership closing the recalls and not honoring the warranty recall on my 2012 Mercedes C250, even though I have received multiple automotive part recall notices for my vehicle. Please see the attached files below for the full story. Thank you for your time.
- Unknown or other
Dear Sir/Madam, I am writing to file a formal complaint against the Fletcher Jones Mercedes-Benz franchise located in Ontario, California and Mercedes-Benz USA , specifically addressing the issue of the dealership closing the recalls and not honoring the warranty recall on my 2012 Mercedes C250…
Dear Sir/Madam, I am writing to file a formal complaint against the Fletcher Jones Mercedes-Benz franchise located in Ontario, California and Mercedes-Benz USA , specifically addressing the issue of the dealership closing the recalls and not honoring the warranty recall on my 2012 Mercedes C250, even though I have received multiple automotive part recall notices for my vehicle. Please see the attached files for more details.
- Service brakes
on 6/20/23 I was driving this vehicle on the 5 freeway north bound exit 102 in Washington. i found myself travelling at 60mph just moving over to the middle lane of traffic. i needed to slow the vehicle a little and pushing down on brakes I found there was no reaction from the braking system.…
on 6/20/23 I was driving this vehicle on the 5 freeway north bound exit 102 in Washington. i found myself travelling at 60mph just moving over to the middle lane of traffic. i needed to slow the vehicle a little and pushing down on brakes I found there was no reaction from the braking system. Making a quick decision I moved over to the emergency lane where I came to a stop. There were no warning signs of the issue. I had the vehicle towed to my Mercedes Benz dealership where I had the car service the day before on 6/19/23 where nothing was noted on this problem. After inspection from the technician at the dealership it was found that the brake vacuum pump was no longer working. Which technician said had caused the issue and he had never experienced this issue before. i am bringing this to your attention due to it could have caused a fatal accident to with me and other people on the freeway.
- Electrical system · Unknown or other
Popping sounds and smoke from center dash and right rear speaker. Center speaker magnet extremely hot to the touch.
- Engine · Structure › Body › Door › Handle › Exterior
The contact owns a 2012 Mercedes-Benz C250. The contact stated while starting the vehicle, the vehicle started very rough with a rattling sound coming from the vehicle. The check engine warning light illuminated. The vehicle was not diagnosed. On another occasion, while opening the front driver’s…
The contact owns a 2012 Mercedes-Benz C250. The contact stated while starting the vehicle, the vehicle started very rough with a rattling sound coming from the vehicle. The check engine warning light illuminated. The vehicle was not diagnosed. On another occasion, while opening the front driver’s side door, the door handle fractured. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was 90,000.
- Electrical system
The contact owns a 2014 Mercedes-Benz C250. The contact stated while driving 70 MPH, there was an abnormal frequency sound coming from the speakers followed by a popping sound. The contact then began to smell a burning electrical wiring odor with white smoke coming from the middle dashboard…
The contact owns a 2014 Mercedes-Benz C250. The contact stated while driving 70 MPH, there was an abnormal frequency sound coming from the speakers followed by a popping sound. The contact then began to smell a burning electrical wiring odor with white smoke coming from the middle dashboard speaker. The contact immediately pulled over and turned off the vehicle. There was no warning light illuminated. Due to the failure, the contact called her father who towed the vehicle to her home where it remained in her possession. The contact reached out to the manufacturer by email and was informed that there were no recalls on the VIN. The contact was then referred to the NHTSA for further assistance. The vehicle was not repaired. The failure mileage was approximately 305,000.
- Air bags
The contact owns a 2012 Mercedes-Benz C250. The contact stated that she noticed that the air bag warning light was illuminated. The dealer was contacted because the vehicle had been serviced under NHTSA Campaign Number: 21V638000 (Air Bags) and the dealer stated that the seat belt was malfunctioning. The vehicle was not repaired. The manufacturer was contacted, and a case was filed. The failure mileage was 78,000.
- Engine
Faulty camshaft adjusters creating timing chain to stretch and tensioners to fail , causing excessive wear to the crankshaft and wear of the teeth resulting in catastrophic damage and complete engine failure ( I have not replaced this timing chain or camshaft adjuster yet but i can hear the timing chain rattling from the defective parts from manufacturer. )
- Steering
The esl/eis failed. Turned car off and after coming back to try and turn it on, it didn't work. Steering wheel was locked and car wouldn't engage with key. After checking with mechanics and checking online, I discovered that it is a frequent issue that happens with no warning whatsoever. Which…
The esl/eis failed. Turned car off and after coming back to try and turn it on, it didn't work. Steering wheel was locked and car wouldn't engage with key. After checking with mechanics and checking online, I discovered that it is a frequent issue that happens with no warning whatsoever. Which is quite worrisome to think the Steering wheel could lock at anytime without notice. My car is a 2012 Mercedes c250 coupe.
- Engine
Auto IS less than 100K miles excellent condition had the turbo gasket go bad on the auto. oil leaking in the main engine compartment and on ground due to the gasket issue. could cause damage to engine and turbo. gasket should not have gone bad. while at the mechanics same issue with the same…
Auto IS less than 100K miles excellent condition had the turbo gasket go bad on the auto. oil leaking in the main engine compartment and on ground due to the gasket issue. could cause damage to engine and turbo. gasket should not have gone bad. while at the mechanics same issue with the same exact model of mercedes, not sure the year but identical body style. repairs were completed on 06/07/22 cost through mechanic $465.00 any time due to passing or excelartion the engine would miss out and lose power for the passing or escelartion.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205225Headlamps fogged.
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167560Fault message in display - Right rear turn signal light inoperative
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
- 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
- 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
- 10167510The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
Every Mercedes-Benz C250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.