2014 Mercedes-Benz C250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › C250 › 2014
These records cover every 2014 Mercedes-Benz C250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2014 Mercedes-Benz C250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.
Risk and remedy
Risk
An incorrect air bag may not function properly in a crash, increasing the risk of injury.
Remedy
Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of…
Risk and remedy
Risk
A loss of steering can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
163 complaints13 involved a crash4 involved a fire11 injuries
What owners report most
Latest complaints
- Steering
The electronic steering lock (ESL) system on my 2014 Mercedes-Benz C250 failed without warning, leaving the vehicle completely unable to start. When attempting to start the vehicle, the key would insert but the vehicle would not crank or start, and the steering lock malfunction prevented normal…
The electronic steering lock (ESL) system on my 2014 Mercedes-Benz C250 failed without warning, leaving the vehicle completely unable to start. When attempting to start the vehicle, the key would insert but the vehicle would not crank or start, and the steering lock malfunction prevented normal operation of the vehicle. The vehicle became stranded and inoperable. This failure created a safety risk because the vehicle could not be moved and left me stranded unexpectedly. If this failure were to occur in an unsafe area or emergency situation, it could place the driver and passengers at risk. After researching the issue, I found numerous reports online from other owners of similar Mercedes-Benz C-Class models experiencing the same ESL/EIS failure. This appears to be a common issue affecting these vehicles. At this time, the problem has not yet been repaired. UNKNOWN if the manufacturer has inspected the vehicle. No warning lights or prior symptoms appeared before the failure. The malfunction happened suddenly and without warning.
- Electrical system
The contact owns a 2014 Mercedes-Benz C250. The contact stated that the vehicle was difficult to start. Additionally, the steering wheel was difficult to turn to the left or the right. The vehicle was eventually started and driven to a dealer; however, after the vehicle was parked and turned off…
The contact owns a 2014 Mercedes-Benz C250. The contact stated that the vehicle was difficult to start. Additionally, the steering wheel was difficult to turn to the left or the right. The vehicle was eventually started and driven to a dealer; however, after the vehicle was parked and turned off, the contact attempted to restart the vehicle; however, the vehicle failed to restart. The dealer replaced the battery however, the vehicle failed to start. The contact stated that the dealer then traced the failure to an anti-theft sensor that shut off the vehicle to deter vehicle theft. The vehicle was repaired. The manufacturer was informed of the failure. The failure mileage was approximately 115,000.
- Engine
my car overheats badly and shakes and it is starting to smoke from the hood in snowy conditions
- Air bags
The contact owns a 2014 Mercedes-Benz C-250. The contact stated that the driver’s side seat air bag warning light was illuminated. The air bag was visible through the seat and was able to be moved manually. The vehicle was taken to a certified mechanic but was not diagnosed. The vehicle was not…
The contact owns a 2014 Mercedes-Benz C-250. The contact stated that the driver’s side seat air bag warning light was illuminated. The air bag was visible through the seat and was able to be moved manually. The vehicle was taken to a certified mechanic but was not diagnosed. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 19V010000 (Air Bags); however, the VIN was not included in the recall, and the recall referenced the front passenger’s seat air bag. The manufacturer was not informed of the failure. The failure mileage was approximately 111,300.
- Engine · Service brakes
I was coming off the freeway on 9/25/25, and when I pressed on the breaks they completely locked up and would not break at all. The car turned off, no warning lights nothing, and I continued to hit the break and the car would not stop, then all of a sudden it came to a stop almost colliding within…
I was coming off the freeway on 9/25/25, and when I pressed on the breaks they completely locked up and would not break at all. The car turned off, no warning lights nothing, and I continued to hit the break and the car would not stop, then all of a sudden it came to a stop almost colliding within inches of hitting the Semi-Truck in front of me. This is the second time in one year that this has happened to me, I have had the car checked out the first time last year immediately, and even paid to diagnose it, nothing, I had the brakes and rotors replaced last June of 2024 when this happened. Since then the car has only been in the dealership to get the car Fully checked out mutltiple times within 2024, 2025 and repaired by Mercedes dealership. On 9/25/25 this happened to me and it was a traumatic experiance when I pressed the break and the break got super hard and in a Locked position and would not come to a stop, there was no warning lights, no engine lights, nothing. (increased braking effort, and potentially I was inches of collision risk. I had the car towed to the nearest shop and was told this is a collapsed break booster Vacuum pump, and possibly the hose and lines and possibly further problems but they would need to replace the Vacuum pump first. After I looked to see if there was a recall on the vacuum pumps in that model on google and it says the following; Google- 2014 Mercedes c250 recall on Vacuum pump A-Premium Vacuum Pump Compatible With Select Mercedes ...Yes, there was a recall on certain Mercedes-Benz vehicles, including some 2014 C250 models, related to a defective brake booster vacuum hose. The recall involves hoses that may delaminate over time, leading to a loss of vacuum, increased braking effort, and potentially a collision risk. To check if your specific 2014 C250 is affected by this recall, you should contact an authorized Mercedes-Benz dealer or visit the Mercedes-Benz USA website to check for open recalls for your vehicle's VIN.
- Steering
The "ESL Module" in this model is designed to unlock the steering and ignition when the vehicle key's passcode matches, using a small, mechanical motor with significantly poor durability. The problem is that this motor's failure is unpredictable, and many users of this model have been stranded and…
The "ESL Module" in this model is designed to unlock the steering and ignition when the vehicle key's passcode matches, using a small, mechanical motor with significantly poor durability. The problem is that this motor's failure is unpredictable, and many users of this model have been stranded and unable to start their vehicles due to the motor's lifespan ending. Even when the car is painstakingly brought to a dealership, repairs cost approximately $1,800 to $2,000, or owners are resorting to unofficial bypasses using a device called an ESL Emulator from the aftermarket. I'd like to request NHTSA to start a thorough investigation into this issue and a RECALL order for the affected models to be issued to MBUSA. Thank you.
- Steering
The contact owns a 2014 Mercedes-Benz C-250. The contact received notification of NHTSA Campaign Number: 17V252000 (STEERING). The contact stated that the recall repair was completed in 2018. The contact stated that the vehicle failed to start. After several attempts, the vehicle failed to start.…
The contact owns a 2014 Mercedes-Benz C-250. The contact received notification of NHTSA Campaign Number: 17V252000 (STEERING). The contact stated that the recall repair was completed in 2018. The contact stated that the vehicle failed to start. After several attempts, the vehicle failed to start. The contact deactivated the push start button and attempted to start the vehicle with the key whoever, but the vehicle failed to start. The vehicle was towed to the dealer, where it was diagnosed and determined that the steering wheel had seized due to the steering coupling connecting bolt. The vehicle remained at the dealer pending the repair. The manufacturer was made aware of the failure. The contact stated that the manufacturer was contacted prior to the dealer repairing the vehicle in 2018. The contact was advised to take the vehicle back to the dealer, where the repair was completed in 2018, to have the vehicle inspected, and if the part that failed was the part replaced under the recall, the manufacturer would pay for the additional repair. The contact stated that the vehicle was not drivable and that the dealer was three hours away. The failure mileage was approximately 70,664.
- Engine
My Mercedes Benz 2014 W204 C250 initially had a noise during startup. The startup noise became louder and now my car does not start. Also, the check engine light indicate a cam shaft position sensor error. Looking online it appears that my problem is exactly like the problem described in a NHTSA…
My Mercedes Benz 2014 W204 C250 initially had a noise during startup. The startup noise became louder and now my car does not start. Also, the check engine light indicate a cam shaft position sensor error. Looking online it appears that my problem is exactly like the problem described in a NHTSA report on 2012-2015 W204 and W172 vehicles(C250 and SLK250) equipped with the M271 engine. I would like NHTSA assistant in getting my Mercedes Benz W024 C250, VIN [XXX] included as part of extended recall of the same car and engine and repaired. If more information is needed, please contact me. [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Steering
The ESL has failed and it has happened in a lot of these cars.i was unable to move my steering wheel.
- Electrical system · Steering
A known issue by many mB owners related to Steering Wheel Lock or ESL system. Car will not start due to a known defect related to a part installed inside the steering wheel preventing owners from starting car safely and to get to destination safely.
- Engine · Power train · Vehicle speed control
Driving on [XXX] to Atlanta GA my car would not automatically shift and began to vibrate badly. I was almost hit by other vehicles as I pulled off the highway to check car out. Car was vibrating badly in idle and when I resumed my trip back home the car would not accelerate properly and caused…
Driving on [XXX] to Atlanta GA my car would not automatically shift and began to vibrate badly. I was almost hit by other vehicles as I pulled off the highway to check car out. Car was vibrating badly in idle and when I resumed my trip back home the car would not accelerate properly and caused tremendous stress and danger. Figured out that car would not shift automatically and I was forced to shift the car manually. Car would sputter and vibrate badly and would only slightly less vibrate to where I could drive it home in gear D5 and would less vibrate at 75+ mph very dangerous, and would lose power and shake violently going up highway hills. I prayed all the way home and barely made it shaken. I called my Mercedes Benz Dealer from the highway and immediately scheduled appointment on 8/15/24. This was a major safety hazard and life threatening situation with my Mercedes Benz C250 2014 car. My car 100% serviced over the years at dealership I bought it from Rick Hendricks Mercedes Benz of Lake Norman NC. Thank you for your time! Actor & Model [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure
The contact owns a 2014 Mercedes-Benz C250. The contact stated that while driving at an undisclosed speed in a rainstorm, the contact observed water entering the vehicle from underneath the driver's side footwell, causing extensive water damage. No warning lights were illuminated. The vehicle was…
The contact owns a 2014 Mercedes-Benz C250. The contact stated that while driving at an undisclosed speed in a rainstorm, the contact observed water entering the vehicle from underneath the driver's side footwell, causing extensive water damage. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was 93,000.
- Engine · Fuel/propulsion system · Unknown or other
I was driving on the highway my car sort of hesitated for a brief second then continued on as if nothing about one mile later my car began to slow down while I was in traffic so asap I pulled over at this point I could only go about 40 miles per hour which was very terrifying at that time it came…
I was driving on the highway my car sort of hesitated for a brief second then continued on as if nothing about one mile later my car began to slow down while I was in traffic so asap I pulled over at this point I could only go about 40 miles per hour which was very terrifying at that time it came a complete stop. After restarting the car 3-4 times it stayed running I continue home which was about 12 miles from my current location. For the next few days I did not go any where. I then had an appointment to have the 80,000 mile maintenance I mentioned the problem I was then told I need a throttle body replacement costing more than $2000 that I can not afford. At that time I started researching my own problem. My relative who works on 18 wheel truck for a living, . that perhaps it just may need cleaning rather than replacement . Also per my research this happens quite often with this model it also stated that Mercedes C250 was the worst Mercedes of that year many many owners have had this problem. The yellow ESP light come on saying it is off also my hold brake no longer works. It work at my prior dealer appointment it while going to appointment afterwards it did not work since over 9 years seldom used I wasn't concerned thus that is the message that appears when car fails Mercedes wants me to pay I believe $2000 problem not needed
- Fuel/propulsion system
I bought my 2014 C250 back in 2017 with 17K miles and currently has 58,570 miles. The issue is with fast acceleration from a stop or slow moving. When trying to accelerate to merge with traffic after a few seconds the vehicle goes into limp mode and the check engine light comes on. In limp mode…
I bought my 2014 C250 back in 2017 with 17K miles and currently has 58,570 miles. The issue is with fast acceleration from a stop or slow moving. When trying to accelerate to merge with traffic after a few seconds the vehicle goes into limp mode and the check engine light comes on. In limp mode I am only able to accelerate very slowly and this is a major concern for my safety. This has been and ongoing issue over the past few years and I have learned to reset it temporarily (around 10 times) with a YouTube fix. I recently found out that there was a recall for the high pressure fuels pump on some C250 models but mine was never included. I also found out that the recall time limit has expired. Please investigate and expand the recall along with the time limit so my vehicle will be included.
- Air bags
The contact owned a 2014 Mercedes-Benz C250. The contact received notification of NHTSA Campaign Number: 19V010000 (Air Bags) and requested to be removed from the recall distribution list. The manufacturer was contacted regarding the issue. The local dealer was not notified.
- Air bags
The passenger airbag was replaced under the Takata recall. Recently the airbag indicator light came on for the driver airbag. We have been notified by the dealership that this airbag needs replaced. They provided an estimate of $2,652.29. We reached out to Mercedes due to this being a safety…
The passenger airbag was replaced under the Takata recall. Recently the airbag indicator light came on for the driver airbag. We have been notified by the dealership that this airbag needs replaced. They provided an estimate of $2,652.29. We reached out to Mercedes due to this being a safety issue and also due to the fact that the passenger airbag was replaced under a recall. They are unwilling to assist. It is illogical that just the passenger airbag is faulty in the recall but that the driver's airbag is fine as they came from the same manufacturer and installed when the vehicle was built. We are concerned about either deploying on its own or if it will deploy in an accident.
- Engine
The contact owns a 2014 Mercedes-Benz C250. The contact stated that upon starting the vehicle, an abnormal rumbling noise was detected. The vehicle had hesitated to start. The engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the timing…
The contact owns a 2014 Mercedes-Benz C250. The contact stated that upon starting the vehicle, an abnormal rumbling noise was detected. The vehicle had hesitated to start. The engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the timing chain tensioner needed to be replaced. The vehicle was not repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 56,000.
- Power train
The contact owns a 2014 Mercedes-Benz C250. The contact stated while depressing the accelerator pedal, the vehicle jerked and then the traction control warning light illuminated. The contact released the accelerator pedal and was able to press the accelerator pedal again to regain normal operation…
The contact owns a 2014 Mercedes-Benz C250. The contact stated while depressing the accelerator pedal, the vehicle jerked and then the traction control warning light illuminated. The contact released the accelerator pedal and was able to press the accelerator pedal again to regain normal operation of the vehicle. The contact continued to drive the vehicle for a few months without experiencing another failure. The contact took the vehicle to the dealer for routine maintenance where it was diagnosed that the differential mounting flange was cracked on the driveshaft. The contact discovered NHTSA Campaign Number: 17V654000 (Power Train) however, the VIN was not included. The vehicle was not repaired due to the parts not being available. The manufacturer was notified of the failure. The failure mileage was approximately 61,192.
- Visibility/wiper
I prchased used with no visible damage to the windshield. In the inclement weather for no apparent reason my windshield began to crack as I was driving the vehicle. I pulled over as soon as I could. The crack stoped and I called the Mercedes Benz manufacture to no avail. I decided to research to…
I prchased used with no visible damage to the windshield. In the inclement weather for no apparent reason my windshield began to crack as I was driving the vehicle. I pulled over as soon as I could. The crack stoped and I called the Mercedes Benz manufacture to no avail. I decided to research to see if this is common and the article says, "that the 2014 Mercedes Benz" windshields are known to crack in extrem cold and hot conditions. The windshield has continued to spider and crack in different direction. I feel threathened at this point and featful for my life that this will implode in my face while driving. I did in good faith reach out to someone.
- Steering
Mercedes has a convenience easy enter/exit feature that lifts the steering and slides the driver's seat back for easy exit and restores the seat and steering when the driver sits down and places the key in the ignition. The safety issue is the steering often gets locked in the up position and…
Mercedes has a convenience easy enter/exit feature that lifts the steering and slides the driver's seat back for easy exit and restores the seat and steering when the driver sits down and places the key in the ignition. The safety issue is the steering often gets locked in the up position and doesn't lower, making it unsafe to drive the car. This is happened 5 times since I bought the car. I had to drive home with the steering wheel locked above the dashboard. The car has been towed to the dealership 4 times under warranty and now I have to get it towed myself. There are approximately 54000 miles on the car.
- Air bags · Structure › Body · Wheels
unknown but I have submitted a previous complaint.
- Engine and engine cooling › Engine › Engine control module (ecu/ecm) · Fuel system, gasoline › Fuel injection system › Injectors · Suspension › Front › Control arm
The contact owns a 2014 Mercedes-Benz C250. The contact stated while driving 60-62 MPH, the vehicle lost motive power. The check engine warning light, the traction control warning light, and other unknown warning lights were illuminated. The contact veered to the side of the road. The contact was…
The contact owns a 2014 Mercedes-Benz C250. The contact stated while driving 60-62 MPH, the vehicle lost motive power. The check engine warning light, the traction control warning light, and other unknown warning lights were illuminated. The contact veered to the side of the road. The contact was able to restart the vehicle after several attempts. The contact was able to continue driving. The dealer was notified of the failure and referred the contact to AutoZone. The vehicle was taken to AutoZone, where it was diagnosed that the fuel injectors and the ECM had failed. The contact sent a diagnostic report to the used car dealer where the vehicle was purchased, but no assistance was provided. Additionally, the contact stated that the control arm had fractured. The vehicle was not repaired. The dealer and manufacturer were not notified of the failure. The failure mileage was approximately 123,000.
- Engine · Visibility › Sun/moon roof assembly
The contact owns a 2014 Mercedes-Benz C250. The contact stated that the vehicle was getting water inside the cabin from a leak coming from the sunroof. The contact stated that while driving at various speeds, the vehicle started jerking and making a choking sound as if the vehicle was going to shut…
The contact owns a 2014 Mercedes-Benz C250. The contact stated that the vehicle was getting water inside the cabin from a leak coming from the sunroof. The contact stated that while driving at various speeds, the vehicle started jerking and making a choking sound as if the vehicle was going to shut off. The check-engine warning light was illuminated. The vehicle was taken to the dealer who determined that there was an electrical failure related to the leak coming from the sunroof leak and that there were corroded cam blocks. The cable for the sunroof was replaced along with the mats on the floor. The contact was unsure if the engine was repaired. The contact stated that the check engine warning light was intermittently illuminated, and the jerking of the vehicle persisted. The manufacturer was not made aware of the failure. The approximate failure mileage was 54,315.
- Unknown or other
Windshield seal failure, moisture in car
- Air bags
I was in an accident that caused my car to be a total loss. I was hit near the front left side, close to the driver's door. The airbag did not deploy despite the hard impact. I am currently having to go to therapy due to impact. My right lower arm was bruised from the impact, and I was in a lot of…
I was in an accident that caused my car to be a total loss. I was hit near the front left side, close to the driver's door. The airbag did not deploy despite the hard impact. I am currently having to go to therapy due to impact. My right lower arm was bruised from the impact, and I was in a lot of pain due to the bruising caused. I am assuming the bruising came from the hit to the steering wheel. I was never notified of an airbag recall.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205248"SOS mbrace service not activated".
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205234Software update of COMAND Online control unit.
- 10205233Mobile phone cotacts are not transferred completely.
- 10205225Headlamps fogged.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
- 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
- 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
- 10167560Fault message in display - Right rear turn signal light inoperative
- 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
- 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.
- 10167536Model X204 (GLK 250 BT) with AMG Styling Package 321. Model Year 2013 Install Tire Fit Kit, Replace Monroney Label
- 10167532A production fault means that the telematics DVD A 166 827 14 00 cannot be used. Because of this the previous telematics DVDs A 204 827 03 65 and A 204 827 10 65 must continue to be used for control unit programming. If required, these are still available for ordering. With XENTRY DVD 03/2014 a new telematics DVD with part number A 166 827 21 00 is being shipped. This telematics DVD replaces the previous telematics DVDs.
- 10167525Apple products (iPhone or iPod) are not charged via the serial USB interface of the COMAND Online control unit (A40/3) in the stowage compartment of the center console.
Every Mercedes-Benz C250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.