2013 Mercedes-Benz CLS550

Recalls

3 recalls name the 2013 Mercedes-Benz CLS550. Newest first.

• Communication

  Nov 1, 2019NHTSA 19V78700024,226 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…

  Risk and remedy

  Risk

  An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

  Remedy

  MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

  Full recall details →

• Exterior lighting

  Mar 10, 2015NHTSA 15V13700030,141 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2015 CLS 400 and CLS 400 4matic, 2012-2015 CLS 550 and CLS 550 4matic, 2012-2013 CLS 63, 2014 CLS 63, and 2014-2015 CLS 63P. The affected vehicles have LED tail lights that may not light on the sides, reducing the rear side visibility of the vehicle. As such, these vehicles fail to comply…

  Risk and remedy

  Risk

  Reduced rear side marker illumination may prevent other drivers from seeing the vehicle, increasing the risk of a crash.

  Remedy

  MBUSA will notify owners, and dealers will update the lighting controller software, free of charge. The recall began April 6, 2015. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2015030005.

  Full recall details →

• Structure › Body › Hood

  Feb 13, 2015NHTSA 15V088000147,224 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 E350 Sedan, E350 4Matic Sedan, E350 4Matic Station Wagon, E400 Hybrid Sedan, CLS 550 CGI, and CLS550 4Matic, 2013-2014 E550 4Matic Sedan, 2013 E63 Sedan, E63 Station Wagon and CLS63, 2014-2015 CLS63 4Matic, E63 4Matic Sedan, E63 4Matic Sedan "S", and E63 4Matic Station Wagon, 2015…

  Risk and remedy

  Risk

  If the rubber seal falls into the engine compartment, it may contact parts of the exhaust system, increasing the risk of a fire.

  Remedy

  MBUSA will notify owners, and dealers will attach four additional retaining clips to the rubber seal, free of charge. The recall began March 6, 2015. Owners may contact MBUSA customer service at 1-201-573-5339. MBUSA's number for this recall is 2015020001.

  Full recall details →

Owner complaints

What owners report most

1. Electrical system1
2. Fuel system, gasoline1
3. Power train1
4. Seat belts1
5. Service brakes1

Latest complaints

• Nov 16, 2023NH
  Service brakes
  I brought the car to my Mercedes dealer for a State required safety and emissions inspection. It passed but they said the rear brake line were rusted and needed replacement at a cost of $2546.00. This model and numerous others were recently provided an extended warranty for rusted subframes. This…

  I brought the car to my Mercedes dealer for a State required safety and emissions inspection. It passed but they said the rear brake line were rusted and needed replacement at a cost of $2546.00. This model and numerous others were recently provided an extended warranty for rusted subframes. This is a $5-$7K repair. They do not cover the brake lines or include them as part of the repair. The sub-frame rust from the inside out so it is not initially obvious of impending failure. There is a pending class action lawsuit against MBUSA that mentions the failure to include the brake line and other components. The rusted brake lines are indicative of internal rust of the subframe. I am facing potential brake failure if I don't act on this expensive repair when clearly Mercedes is not acting in good faith to repair the entirety of their faulty components.

• Apr 11, 2022AZ
  Electrical system · Power train

  Car looses communication with the Electronic Ignition System (keyless system) and while rolling to a stop light, slams the car into park while still rolling. It also will throw itself into park while first accelerating - almost causing the car following me to crash into my rear end.

• Dec 7, 2020TX85,000 mi
  Fuel system, gasoline
  TL* the contact owns a 2013 mercedes-benz cls550. The contact stated that after refueling and parking in the garage, the odor of fuel was present coming from the vehicle. Upon inspection, it was discovered that fuel had leaked from under the rear driver's side seat. The cause of the failure was not…

  TL* the contact owns a 2013 mercedes-benz cls550. The contact stated that after refueling and parking in the garage, the odor of fuel was present coming from the vehicle. Upon inspection, it was discovered that fuel had leaked from under the rear driver's side seat. The cause of the failure was not yet determined. Neither the manufacturer nor the local dealer were notified of the failure. The failure mileage was 85,000.

• Oct 18, 2017AL50,000 mi
  Seat belts

  TL* the contact owns a 2013 mercedes-benz cls550. The contact stated that the seat belt did not retract. The vehicle was not taken to an independent mechanic or a dealer for diagnostic testing. The manufacturer was notified of the failure. The vehicle was not repaired. The approximate failure mileage was 50,000.

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
• 10240203This NCU replaces the prior NCU issued on May 11, 2023, and clarifies replacement part information. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, is extending the warranty coverage on the catalytic converter system in certain Model Year (MY) vehicles fitted with the M278 8-cylinder engine listed below: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 13 years / 156,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 144,000 miles (whichever occurs first) - MY2013: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 132,000 miles (whichever occurs first) - MY2014 MY2020: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first)
• 10237240This extended warranty applies to the following condition that may necessitate the repair or replacement of the catalytic converter system and is related to: A check engine Malfunction Indicator Lamp (MIL) may illuminate due to sulfur contamination in the catalyst.
• 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10233794Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).
• 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10233778In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below as follows: - MY2011: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 12 years / 120,000 miles (whichever occurs first) - MY2012: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 11 years / 120,000 miles (whichever occurs first) - MY2013 MY 2016: Original New Vehicle Limited Warranty of 4 years / 50,000 miles New Vehicle to 10 years / 120,000 miles (whichever occurs first) This extended warranty applies to the following condition that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinderhead) related to: Over time, increased lateral forces may lead to wear in the valve guide and/or seat ring. This issue could potentially cause combustion misfire for cylinder 1 through 8 (right and/or left cylinder head), resulting in an activation of the check engine Malfunction Indicator Lamp (MIL) .
• 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
• 10205265Outside mirror fogged.
• 10205248"SOS mbrace service not activated".
• 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
• 10205239"Anti-theft protection activated".
• 10205237The COMAND unit does not start or the display remains dark.
• 10205236"Metadata loss- Please reimport all media data".
• 10205234Software update of COMAND Online control unit.
• 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
• 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
• 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167556Glove box squeaks/rattles at top left mounting.
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.

Every Mercedes-Benz CLS550 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.