2016 Mercedes-Benz E400
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › E400 › 2016
These records cover every 2016 Mercedes-Benz E400. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2016 Mercedes-Benz E400. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.
Risk and remedy
Risk
An incorrect air bag may not function properly in a crash, increasing the risk of injury.
Remedy
Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2016 GLE300d 4Matic, E400 4Matic Coupe, GL63 AMG, GLE350, GLE350 4Matic, GLE350d 4Matic, GLE400 4Matic, GLE43 AMG Coupe 4Matic, GLE550e 4Matic, GLE63 AMG 4Matic, GLE63S AMG 4Matic and GLE63S AMG Coupe 4Matic vehicles, 2017 E300 4Matic and GLS63 AMG 4Matic vehicles, and 2016-2017 GL350 4Matic BlueTec…
Risk and remedy
Risk
If water enters the power steering control unit, the power steering assist may be deactivated, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the connector and inspect the electric power steering rack, replacing the rack as necessary. These repairs will be performed free of charge. Remedy parts are currently unavailable. Interim notices informing owners of the safety risk are expected to be mailed June 30, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 SL550, 2013-2014 SL63 AMG, 2014-2016 E350, 2014 E350 Cabriolet, E350 Coupe, 2014-2015 S550, 2015 E350 Bluetec, 2015-2016 E400, 2016 E550 Coupe, and Maybach S600 vehicles manufactured August 23, 2012, to August 14, 2015. The affected vehicles use an electric power steering system that…
Risk and remedy
Risk
If the control unit pins lose connection, there would be a loss of electric power steering assist, increasing the risk of a crash. The increase in pin contact resistance can also increase the risk of a fire, even while the vehicle is parked and ignition is off.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering control unit, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 Mercedes Benz E350, E400, E400 4Matic, E63 4M S AMG, E350 4Matic, E63-4M S AMG, 2015 CLS400, CLS400 4Matic, CLS550, CLS63-4M "P" AMG, and CLS550 4Matic vehicles manufactured April 16, 2015, to April 22, 2015. The integral steel cable that secures the rubber seal to the bulkhead might have…
Risk and remedy
Risk
If the rubber seal falls into the engine compartment, it may contact parts of the engine or exhaust system, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will replace the rubber seal, in the engine compartment, free of charge. The recall began on September 2, 2015. MBUSA's number is 2015080001. Owners may contact MBUSA customer service at 1-201-573-5339.
Owner complaints
34 complaints1 involved a crash
What owners report most
Latest complaints
- Electrical system · Forward collision avoidance › Adaptive cruise control
The contact owns a 2016 Mercedes-Benz E400. The contact stated that upon starting the vehicle, there was a knocking sound coming from the vehicle. The check engine warning light was illuminated. The automatic brake and Adaptive Cruise Control warning lights were illuminated. The emergency braking…
The contact owns a 2016 Mercedes-Benz E400. The contact stated that upon starting the vehicle, there was a knocking sound coming from the vehicle. The check engine warning light was illuminated. The automatic brake and Adaptive Cruise Control warning lights were illuminated. The emergency braking system engaged independently. The vehicle was taken to an independent mechanic who determined that there was oil leaking from the gasket and was dripping onto the engine. The contact called the local dealer, who confirmed that there was no recall under the VIN. The vehicle was not diagnosed or repaired. The failure mileage was approximately 134,000.
- Engine
Mercedes Benz has a recall on several models including E-Class (E 200, E 220, E 280, E 350) experiencing timing chain problems. The timing chain is an important component of the engine, as it helps to coordinate the timing of the engine’s various parts. I am currently having the same issue, but my…
Mercedes Benz has a recall on several models including E-Class (E 200, E 220, E 280, E 350) experiencing timing chain problems. The timing chain is an important component of the engine, as it helps to coordinate the timing of the engine’s various parts. I am currently having the same issue, but my model is an (E400) which has not been included in the recall. It appears that my timing chain failing, which is causing a number of problems with the engine, including reduced performance and fuel efficiency, and if MB does not recall this model, I am facing complete engine failure.
- Engine
The contact owns a 2016 Mercedes-Benz E400. The contact stated that while driving at various speeds the vehicle would display a vibration sensation. The check engine light had illuminated. The vehicle was taken to the dealer where it was diagnosed that the head gasket had failed. The head gasket…
The contact owns a 2016 Mercedes-Benz E400. The contact stated that while driving at various speeds the vehicle would display a vibration sensation. The check engine light had illuminated. The vehicle was taken to the dealer where it was diagnosed that the head gasket had failed. The head gasket and engine needed to be replaced. The vehicle had not been repaired. The manufacturer was made aware of the failure. The failure mileage was 106,000.
- Back over prevention
The contact owns a 2016 Mercedes-Benz E400. The contact stated while reversing the Back Over Prevention camera screen was blank. There was no warning light illuminated. The vehicle was taken to the dealer and the dealer stated that no failure was found. The vehicle was not repaired. The…
The contact owns a 2016 Mercedes-Benz E400. The contact stated while reversing the Back Over Prevention camera screen was blank. There was no warning light illuminated. The vehicle was taken to the dealer and the dealer stated that no failure was found. The vehicle was not repaired. The manufacturer was contacted and notified of the failure. The contact was referred to the NHTSA Hotline to file a complaint. The failure mileage was 62,000.
- Steering
The contact owns a 2016 Mercedes-Benz E400. The contact stated upon starting the vehicle, a message indicating a power steering malfunction was displayed and the vehicle lost power steering functionality. The vehicle was towed to the dealer, where an unknown software update was completed. The…
The contact owns a 2016 Mercedes-Benz E400. The contact stated upon starting the vehicle, a message indicating a power steering malfunction was displayed and the vehicle lost power steering functionality. The vehicle was towed to the dealer, where an unknown software update was completed. The failure ceased but reoccurred a year and a half later. The vehicle was taken to the dealer, where it was diagnosed that the power steering assist assembly needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 17V241000 (Steering); however, the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was approximately 29,000. The consumer stated the power steering assist assembly needed to be replaced and it was repaired in the amount of $4042.00.
- Steering
Steering wheel stuck in Up Position
- Steering
I was waiting at a light when the message “steering wheel malfunction” can up. I was forced to turn left, which I did with great difficulty as the power assist stop working. I managed to go straight 3 blocks despite the hard steering with my emergency lights on at 5 mph and turn left two short…
I was waiting at a light when the message “steering wheel malfunction” can up. I was forced to turn left, which I did with great difficulty as the power assist stop working. I managed to go straight 3 blocks despite the hard steering with my emergency lights on at 5 mph and turn left two short blocks to get home. I was in my car with my two children. If this would have happened in the highway, I am certain that it would have resulted in an accident.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. Mercedes-benz of fort mitchell (2100 dixie hwy, fort mitchell, ky 41011, (859) 331-1500)…
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. Mercedes-benz of fort mitchell (2100 dixie hwy, fort mitchell, ky 41011, (859) 331-1500) was contacted and it was confirmed that the part was not yet available. The manufacturer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. Parts distribution disconnect. *Dt
- Air bags
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the…
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact contacted park place motorcars dallas (6113 lemmon avenue, dallas tx, 75209, (214) 526-8701) was contacted and confirmed that parts were available replaced on may 4TH, 2021. The manufacturer was not made aware of the issue. Vin tool confirms parts not available.
- Air bags · Service brakes
Right passenger air bag malfunction. parking brake fail to engage.
- Air bags
The dealership still doesn't have a remedy for takata recall over 2 years later
- Air bags
On 02/15/2019, I received a letter from mercedes-benz USA, llc, regarding mbusa recall # 2019010001. The letter advised that "the passenger side airbag in your vehicle IS affected by this recall based on the defect decision of tk holdings, inc. ('Takata')". In the two-year period since my receipt…
On 02/15/2019, I received a letter from mercedes-benz USA, llc, regarding mbusa recall # 2019010001. The letter advised that "the passenger side airbag in your vehicle IS affected by this recall based on the defect decision of tk holdings, inc. ('Takata')". In the two-year period since my receipt of the original letter, I have received no follow-up communications from the manufacturer regarding this issue. I have proactively contacted both mercedes-benz USA and my local dealership multiple times, in an attempt to obtain some indication as to when the recall will be addressed, only to be informed that the status IS still "pending".
- Air bags
2016 mercedes benz E400. Consumer writes in regards to airbag safety recall. *Ld the consumer was informed the parts to repair the vehicle were not yet available. The consumer stated the repair exceeded a reasonable amount of time. *js *js
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. The contact contacted mercedes-benz of cherry hill (2151 NJ-70, cherry hill, nj 08002; (856)…
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. The contact contacted mercedes-benz of cherry hill (2151 NJ-70, cherry hill, nj 08002; (856) 663-3200) where it was confirmed that parts were not yet available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bag). After contacting mercedes of south orlando located at 4301 millenia blvd, orlando, fl 32839, and the manufacturer, the contact was informed that the parts…
TL* takata recall. The contact owns a 2016 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bag). After contacting mercedes of south orlando located at 4301 millenia blvd, orlando, fl 32839, and the manufacturer, the contact was informed that the parts needed for the recall remedy were still not available and no estimated time for receiving the parts could be provided. The contact had not experienced a failure. The contact was concerned the manufacturer had exceed a reasonable amount of time for the recall repair. Vin tool confirms parts not available. *bf*jb
- Suspension · Wheels
Chamfer bolts bent by potholes. Caused uneven wear of tread and multiple flats over past year. *tr
- Air bags
Tla* taste recall. The contact owns a 2016 mercedes benz E400. the contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do recall the repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the…
Tla* taste recall. The contact owns a 2016 mercedes benz E400. the contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do recall the repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. An unknown dealer was contacted and confirmed that the part was not available. The manufacturer was made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.*dt*jb
- Power train · Steering
TL* the contact owns a 2016 mercedes benz E400. The contact stated that the vehicle was taken to mercedes benz of hunt valley 9800 york road cockeysville, md 21030, (410)-666-7777 to be repaired under nhtsa campaign number: 17v241000 (steering). The contact stated that the free repair failed to fix…
TL* the contact owns a 2016 mercedes benz E400. The contact stated that the vehicle was taken to mercedes benz of hunt valley 9800 york road cockeysville, md 21030, (410)-666-7777 to be repaired under nhtsa campaign number: 17v241000 (steering). The contact stated that the free repair failed to fix the failure stated in the recall. The contact stated that there was an abnormal sound when the accelerator pedal was depressed. The contact stated that the sound disappeared when the vehicle exceeded 40 mph. The vehicle was not diagnosed nor repaired. The manufacturer was notified of the failure. The failure mileage was 18,763.
- Air bags
I bought this car used from mercedes benz in may 2019, and decided to rent it on turo to pay monthly payments of the loan, but turo rejected it as it has a recall on it, --------------------------------------------------- mercedes-benz USA IS recalling certain my 2010-2017 c-class, glk-class…
I bought this car used from mercedes benz in may 2019, and decided to rent it on turo to pay monthly payments of the loan, but turo rejected it as it has a recall on it, --------------------------------------------------- mercedes-benz USA IS recalling certain my 2010-2017 c-class, glk-class, sls-class and e-class coupe mercedes-benz vehicles equipped with passenger-side frontal airbags affected by the defect decision of tk holdings, inc. ( takata ). Under certain circumstances during a crash that necessitates frontal airbag deployment, the defect in your passenger-side frontal airbag inflator may cause the inflator to explode. A passenger-side inflator explosion during deployment could result in metal fragments striking the front passenger or other occupants, possibly causing serious injury or death. safety risk: according to takata, in the event of an inflator explosion, metal fragments could pass through the air bag cushion material, which may result in injury or death to vehicle occupants. remedy: an authorized mercedes-benz dealer will replace the passenger-side airbag. recall status: recall incomplete. Remedy not yet available
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the parts to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the…
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the parts to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Mercedes-benz of gilbert 3455 s gilbert rd, gilbert, az 85297, was contacted and confirmed that the part for the recall repair was not available. The contact had not experienced a failure. The manufacturer was not made aware of the issue. The vin was provided but could not be decoded.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz e400a. The contact received a recall notice for nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of raleigh (5607 capital blvd…
TL* takata recall. The contact owns a 2016 mercedes-benz e400a. The contact received a recall notice for nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of raleigh (5607 capital blvd, raleigh, nc 27616, (919) 573-5050) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
I had a mercedes ml350. there was a safety recall on that vehicle. I went to the dealership and the salesman told me that the E400 did not have the same airbags in the car and that it would be safe. I purchased the new vehicle and thought I was safe. now I have had a recall for the airbags and…
I had a mercedes ml350. there was a safety recall on that vehicle. I went to the dealership and the salesman told me that the E400 did not have the same airbags in the car and that it would be safe. I purchased the new vehicle and thought I was safe. now I have had a recall for the airbags and I do not feel safe. there IS not a "fix" for my vehicle at this time. I do not feel safe. that IS why I bought a new vehicle. I am in the same situation that I was in before the purchase. the letter came out in march and I spoke to the service department and they said that they should be getting new airbags soon. this IS now september, and still nothing can be done.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of paramus (located at 755 NJ-17…
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of paramus (located at 755 NJ-17, paramus, nj 07652, (201) 977-6365) was contacted and confirmed that the part was not available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that mercedes-benz of union (located at 2585 US-22, union, nj 07083, (908) 356-6805) exceeded a reasonable amount of time for the…
TL* takata recall. The contact owns a 2016 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that mercedes-benz of union (located at 2585 US-22, union, nj 07083, (908) 356-6805) exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and stated that the part was not available for the repair. The contact had not experienced a failure. Parts distribution disconnect.
- Air bags
TL* takata recall. The contact owns a 2016 mercedes-benz e400c4. the contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of littleton (8070 s broadway…
TL* takata recall. The contact owns a 2016 mercedes-benz e400c4. the contact received notification of nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Mercedes-benz of littleton (8070 s broadway, littleton, co 80122, (303) 738-7700) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue. The contact had not experienced a failure. vin tool confirms parts not available.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007750Complaint Dynamic seat function or multicontour system inoperative Noises from area of lateral support bladder Cause Lateral support bladder leaking Remedy Replacement of complete air cushion insert.
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003218Complaint Complaints about shift quality in vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2. Cause If the shift adaptation is not performed as described under "Remedy", the adaptation values may not be saved correctly under certain circumstances. Remedy In vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2, it must be ensured that the adaptation of the shifts is performed only as described below. Acceleration upshifts may only be adapted in transmission mode "S" Acceleration downshifts may only be adapted in transmission mode "S" Coast down shifts may only be adapted in transmission mode "E"
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10238425The trunk lid is not drawn into the end position with the help of the trunk lid power closing function after the electric closing process. There is a loud rattling from the trunk or from the trunk lid power closing unit (M14/31). Toothed drive wheel in trunk lid power closing unit (M14/31) has run over the limit stop. Remedy Replace trunk lid power closing unit (M14/31).
- 10235972Enclosed for your information and pursuant to part 579.5, please find our latest Service and Warranty Bulletins for March, 2016
- 10235673To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232334To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10231042To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to allegations that the Burl Walnut Trim in model year 2010 to 2016 Mercedes-Benz E-Class (212 platform) vehicles is defective. This Burl Walnut Trim is also sometimes referred to as Burred Walnut. The purpose of this NCU update is to alert you that: 1. The settlement went into effect on January 23, 2023. Customers are now eligible to receive extended warranty coverage and may start contacting authorized Mercedes-Benz dealerships to schedule an appointment for the repairs. 2. Before scheduling a repair appointment and ordering replacement parts kits: The customer should be given a repair order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the repair order before the parts kit can be ordered.
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205265Outside mirror fogged.
- 10205248"SOS mbrace service not activated".
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205239"Anti-theft protection activated".
- 10205237The COMAND unit does not start or the display remains dark.
- 10205236"Metadata loss- Please reimport all media data".
- 10205234Software update of COMAND Online control unit.
Every Mercedes-Benz E400 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.