2017 Mercedes-Benz E400
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › E400 › 2017
These records cover every 2017 Mercedes-Benz E400. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
8 recalls name the 2017 Mercedes-Benz E400. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 E450 4MATIC Wagon, 2017-2018 E400 4MATIC Wagon, and 2018-2019 E63S 4MATIC Wagon vehicles. The rear spoiler may detach.
Risk and remedy
Risk
If the spoiler detaches while driving, it can become a road hazard, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect and correct the mounting of the spoiler, as necessary, free of charge. The recall began October 18, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. Note: This recall is an expansion of NHTSA recall number 18V-849. MBUSA's number for this recall is 2019090008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2017 Mercedes-Benz E300 4Matic, E300, E43 AMG, and E400 vehicles. The headlight horizontal adjustment screws on these vehicles may not be properly sealed behind a non-removable sealing cap to keep headlights from being readjusted. As such, these vehicles fail to comply with the requirements of Federal…
Risk and remedy
Risk
If the headlight's horizontal aim is altered, a misaimed headlight may lead to an insufficiently illuminated roadway, which may increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will retrofit the sealing caps for the headlights, free of charge. The recall is expected to begin in June 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018050012.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2015-2017 C300 4Matic, C300, CLA250, CLA250 4Matic and CLA45 AMG vehicles, 2017 C300 4Matic Cabrio, C300 4Matic Coupe, C300 Cabrio, C300 Coupe, E300, E300 4Matic, E400 4Matic Wagon, E43 AMG 4Matic, GLA250, GLA250 4Matic and GLC300 4Matic Coupe vehicles and 2016 C350e and GLC300 vehicles and 2016-2017 C450…
Risk and remedy
Risk
If the starting current limiter overheats, the surrounding components can melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will install an additional fuse in the electrical line to the starter, free of charge. The recall began August 31, 2017. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2017080002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 CLA250, CLA250 4Matic, E400 Coupe, E400 4Matic Coupe, E550 Coupe, E400 Cabriolet, E550 Cabriolet, E300, E300 4Matic, E400 Wagon, GLA250, and GLA250 4Matic vehicles. The pelvis air bag or the front passenger air bag inflator initiator may fail to ignite in the event of a crash.
Risk and remedy
Risk
If the pelvis airbag or the front passenger airbag does not deploy as intended in the event of a crash, the occupants have an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the affected air bag modules, free of charge. The recall began March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2017 E400 4Matic Coupe, E400 Convertible, E550 Coupe and E550 Convertible vehicles manufactured June 7, 2016, to September 8, 2016. On the affected vehicles, there may be insufficient clearance between the left catalytic converter and the composite underbody panel.
Risk and remedy
Risk
The insufficient clearance may cause the panel to melt, increasing the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will inspect and replace the underbody panel, as necessary, free of charge. The recall began December 2016. Owners may contact Mercedes customer service at 1-800-367-6372.
Owner complaints
20 complaints4 injuries
What owners report most
Latest complaints
- Structure
The contact owns a 2017 Mercedes-Benz E400 Coupe. The contact stated that the silver metal coating on the seat release lever was rough and jagged on both driver and passenger sides of the two door vehicle. The contact's son had grabbed the front seat release lever to access the rear passenger’s…
The contact owns a 2017 Mercedes-Benz E400 Coupe. The contact stated that the silver metal coating on the seat release lever was rough and jagged on both driver and passenger sides of the two door vehicle. The contact's son had grabbed the front seat release lever to access the rear passenger’s side seat and cut his hand. The cut was approximately 2-3 inches long. No medical attention was needed. The vehicle was taken to the dealer, and the contact was informed that the failure was common with the vehicle and that the coating was known to peel due to heat. The contact was concerned that the failure occurred as his vehicle was stored in the garage and sustained less heat exposure due to its maintenance/care. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline for assistance. The approximate failure mileage was 42,000.
- Air bags · Seats
Seat pressure sensor for supplemental restraint system (SRS) routinely fails. The system generates and error and disables the front passenger airbag. The condition clears when the vehicle is turned off. Sensors have been recalibrated multiple times. System still routinely fails.
- Seats
Safety Issue. The Chrome on the lever to make the seat move forward to access the back seat has sharp razor blade ridges. It has cut my hand open multiple times as well as my wife and a friend. A lot of blood, this is a serious issue. When I brought my car to the Mercedes Service center the agent…
Safety Issue. The Chrome on the lever to make the seat move forward to access the back seat has sharp razor blade ridges. It has cut my hand open multiple times as well as my wife and a friend. A lot of blood, this is a serious issue. When I brought my car to the Mercedes Service center the agent told me this is a known problem and he too has cut his hand open on customers cars. This is not from wear and tear, this lever is used in frequently, I see a lot of complaints on the blogs too. Mercedes will not fix it. The Part is only $270 but they want $650 to install it.
- Unknown or other
I was driving down the interstate when the panoramic sunroof suddenly shattered. Luckily my shade was closed but it is leaving me with a costly repair bill. I was not driving near any other vehicles, had not gone under an overpass, nor did a rock hit my roof. How could this happen and how can this be resolved? Who do I contact?
- Air bags
TL* takata recall. The contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. The contact called mercedes-benz of long beach (2300 e spring st, signal hill, ca 90755) where…
TL* takata recall. The contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. The contact called mercedes-benz of long beach (2300 e spring st, signal hill, ca 90755) where it was confirmed that the part was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags
Takadaairbag recall. No repair available for over 2 years, and no answer from meercedesdealer, regional office or us headquarters. In fear of air bag explosion and not safe to have passenger in front seat.
- Air bags
TL* takata recall. The contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the…
TL* takata recall. The contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. Mercedes-benz of sarasota (located at 4754 clark rd, sarasota, fl 34233, (941) 275-1293) was made aware of the issue. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.*dt*jb
- Air bags
This IS a complaint about the lack of response by mercedes benz in replacing the defective takata passenger airbag. my understanding IS that mercedes benz has addressed only 35% of recalled models as opposed to honda who has already responded to 85% of the recalled models, replacing the defective…
This IS a complaint about the lack of response by mercedes benz in replacing the defective takata passenger airbag. my understanding IS that mercedes benz has addressed only 35% of recalled models as opposed to honda who has already responded to 85% of the recalled models, replacing the defective airbags in question. I called the daytona mercedes benz dealer when I received the recall notice in january 2019 requesting that the defective passenger airbag be replaced. they replied that the part was not available and would notify me when it would be available. as of two days ago, october 14, 2020 I had not heard from the dealer or from mercedes benz. since then I have found documentation as to the danger of this airbag and how it has killed or injured hundreds of people. are we expected to drive this car under these conditions? does mercedes benz give a hoot about its customers? I am not driving my car because it doesn't take much for these airbags to deploy. the car has been sitting in my garage even though I am paying taxes and insurance on it. I am 79 years old living on a small pension and do not think I will be able to sell this car with this recall pending. yesterday I called mercedes benz customer service and they replied that the part will be available in november 2020. I am filing this claim with nhtsa to notify you that I am one of the affected customers and will be notifying you again whether or not the part IS replaced in november. follow through.
- Air bags
No parts available for recall
- Air bags
Sales staff told me that airbag, light and paint issue was fixed. after completing the deal, the stories began. I tried to return the car to no avail. The salesman told me the airbag recall was of no harm. Later I read the information on your website that this recall of the airbag could cause harm and death. Nothing has happened however I am afraid to drive it or to have a passenger in the car
- Air bags
TL* the contact owns a 2017 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. Mercedes-benz of white plains (50 bank st, white plains, ny 10606) was contacted and confirmed that the part…
TL* the contact owns a 2017 mercedes benz E400. The contact received notification of nhtsa campaign number: 19v010000 (air bags) however, the part to do the recall repair was unavailable. Mercedes-benz of white plains (50 bank st, white plains, ny 10606) was contacted and confirmed that the part was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. the manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available. *Bf*jb
- Air bags
I am waiting to buy this car but do not want to buy until the airbags are fixed. the car has remained on recall of airbags since jan. 2019.
- Air bags
Takata recall. I have been waiting months for a fix to this recal problem. What IS taking so long for them to come up with a solution. I am starting to get very worried about the safety of my passengers and myself.
- Air bags
Takata recall I do not feel safe driving my car and want the dealership to give me a loaner.
- Air bags
2017 mercedes benz E400. Consumer writes in regards to takata safety airbag recall. *Ld *tr
- Air bags
2017 mercedes benz E400. Consumer writes in regards to passenger side airbag safety defect. *Ld *tr
- Air bags
TL* takata recall. The contact owns a 2017 mercedes-benz e400a. The contact received an unknown recall regarding the air bags. The contact received the recall notice in february of 2019. The dealer was not contacted. The manufacturer was contacted and stated that the air bags were not available and…
TL* takata recall. The contact owns a 2017 mercedes-benz e400a. The contact received an unknown recall regarding the air bags. The contact received the recall notice in february of 2019. The dealer was not contacted. The manufacturer was contacted and stated that the air bags were not available and may not be available until may of 2020. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags · Electrical system · Steering
Takata airbag defect. I received notice of recall from mb in november, 2017, almost 8 months ago. Despite numerous followups with both mb and the dealer, neither mb or the mb dealer can tell me when the parts will be available to correct this serious safety problem. Please help before my wife or…
Takata airbag defect. I received notice of recall from mb in november, 2017, almost 8 months ago. Despite numerous followups with both mb and the dealer, neither mb or the mb dealer can tell me when the parts will be available to correct this serious safety problem. Please help before my wife or I or other persons are injured or worse. the mb notice states that the airbag may deploy due to insufficient electrical grounding, an electrostatic discharge and a broken steering module clock spring, causing injury and risk of a crash.
- Air bags
TL* the contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The…
TL* the contact owns a 2017 mercedes-benz E400. The contact received notification of nhtsa campaign number: 17v627000 (air bags); however, the part needed for the repair was not available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The vehicle was taken to mercedes-benz of palm spring (4095 e palm canyon dr, palm spring, ca 92264), but the part was not available for the repair. The manufacturer stated that an email would be sent and the contact was referred to nhtsa. The contact had not experienced a failure. Vin tool confirms parts not available.
- Tires › Sidewall
TL* the contact owns a 2017 mercedes-benz E400 convertible equipped with michelin m+s tubeless radio x tires, size: 255/35/r18 94H (na). While driving 60 mph, the contact noticed that the rear passenger side tire was flat. The vehicle was towed to an independent mechanic where it was diagnosed that…
TL* the contact owns a 2017 mercedes-benz E400 convertible equipped with michelin m+s tubeless radio x tires, size: 255/35/r18 94H (na). While driving 60 mph, the contact noticed that the rear passenger side tire was flat. The vehicle was towed to an independent mechanic where it was diagnosed that the rear passenger side tire had a bubble on the sidewall. The tire was inflated. While driving 60 mph, the vehicle shook uncontrollably and the rear passenger side tire blew out suddenly. The tire pressure indicator illuminated. The vehicle was taken to capital eurocars (3705 w tennessee st, tallahassee, fl 32304 at (888) 701-6470), but the failure could not be replicated. The vehicle was not repaired. The manufacturer was not notified of the failure. The vin was unknown. The approximate tire and vehicle failure mileage was 2,000.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003218Complaint Complaints about shift quality in vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2. Cause If the shift adaptation is not performed as described under "Remedy", the adaptation values may not be saved correctly under certain circumstances. Remedy In vehicles of MODEL 205, 212 and 222 with TRANSMISSION 724.2, it must be ensured that the adaptation of the shifts is performed only as described below. Acceleration upshifts may only be adapted in transmission mode "S" Acceleration downshifts may only be adapted in transmission mode "S" Coast down shifts may only be adapted in transmission mode "E"
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10243565In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the intake line assembly on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years / 150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2015 - 2020 C/E/GLC/SLC and SLK vehicles, under certain circumstances, the partial-load ventilation valve (a part of the intake line assembly) may not work as intended, resulting in the illumination of the check engine Malfunction Indicator Lamp (MIL). A faulty partial-load ventilation valve might also increase exhaust gas emission. . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10238424In the MBUX weather app, the temperature is displayed in the wrong unit (Fahrenheit instead of C, or vice versa). Temperature setting in Mmc mobile application settings incorrect Remedy Adjust the setting in the Mercedes me connect app via mobile phone (settings -> units)
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233783Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10227148Complaint The trunk lid is not latching into the closed position with the help of the trunk lid power closing function after the electric closing process. There is a loud rattling from the trunk or from the trunk lid power closing unit (M14/31). Cause Under Analysis Remedy Please create a PTSS case to MBUSA before attempting repair on the vehicle
- 10222481Complaint Customer states after a bus sleep the SiriusXM category changes from "My Favorites" to "All Stations" or a different category. Sometimes, the "My Favorites" category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be updated once the software is released.
- 10222461Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10217216Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has extended the warranty for the accelerator pedal wiring harness and connectors from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 10 years/120,000 miles for certain Model Year (MY) 2016-2019 Mercedes-Benz E-Class and GLC-Class vehicles (213, 238, and 253 platforms).
- 10217163Complaint The Apple Carplay interface cannot be controlled via the center console touchpad or the right-hand steering wheel touchpad. Cause A setting on the iPhone may prevent control via the touchpad Remedy To remedy on the affected iPhone, navigate to "Settings" -> "Accessibility" -> "Touch" and turn the "BackTap" option OFF.
- 10217157Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10217154Complaint Thumping noise on rear axle shock absorber on rough road. Cause Until now the rear axle shock absorber support bushing was only available together with the rear axle shock absorber as a replacement part. In future, the rear axle shock absorber support bushing will be available individually as a replacement part to avoid any unnecessary shock absorber noise. Remedy For noise problems on the rear axle shock absorbers, please always make a noise diagnosis, for example using Chassis Ear to localize any sources of noise on shock absorbers or support bushings. If the noise originates from the upper part of the shock absorbers, it is enough to replace the support bushings. Otherwise the complete shock absorber including support bushing have to be replaced. The modified support bushings must be replaced in pairs the first time so that any mixed installation of old and new is reliably ruled out.
Every Mercedes-Benz E400 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.