2015 Mercedes-Benz Gla 250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Gla 250 › 2015
These records cover every 2015 Mercedes-Benz Gla 250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2015 Mercedes-Benz Gla 250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (Mercedes-Benz) is recalling certain model year 2015 CLA250, CLA250 4Matic, GLA250, GLA250 4Matic, and 2016 SLK300 roadster vehicles manufactured July 17, 2015, to August 31, 2015. The affected vehicles have intake or exhaust camshafts whose welds may fail and possibly cause engine damage.
Risk and remedy
Risk
Engine damage may result in a stall, increasing the risk of a crash.
Remedy
Mercedes-Benz will notify owners, and dealers will replace the affected camshafts, free of charge. Interim notices were mailed to owners on December 9, 2015. The recall began on December 23, 2015. Owners may contact Mercedes-Benz customer service at 1-800-367-6372. Mercedes-Benz's number for this recall is 2015100006.
Owner complaints
94 complaints4 involved a crash1 involved a fire8 injuries
What owners report most
Latest complaints
- Structure › Body · Suspension
During an inspection, an authorized Mercedes-Benz dealership discovered severe corrosion and perforation, including holes, in the rear subframe of my 2015 Mercedes-Benz GLA. There were no warning lights or messages alerting us to the condition before it was discovered. The dealership confirmed that…
During an inspection, an authorized Mercedes-Benz dealership discovered severe corrosion and perforation, including holes, in the rear subframe of my 2015 Mercedes-Benz GLA. There were no warning lights or messages alerting us to the condition before it was discovered. The dealership confirmed that the subframe requires replacement and estimated the repair at approximately $6,000. The vehicle has approximately 140,000 miles. The rear subframe is a structural component that supports suspension components. Its advanced corrosion and perforation create concern that it could weaken or fail while the vehicle is being driven, potentially affecting vehicle stability and control. The vehicle and affected component are available for inspection upon request, and photographs of the corrosion and holes are available. Mercedes-Benz USA was notified of the problem but has not agreed to cover the repair. Mercedes-Benz has issued a 20-year/unlimited-mile extended warranty for corrosion with perforation of rear subframes on several other Mercedes-Benz models, but the GLA is not currently included. I am reporting this because the same type of premature structural subframe corrosion appears to be occurring in this vehicle and may present a safety defect affecting other GLA owners.
- Air bags
I came out from work. Got in my car and started it and went to make a three-point turn to go the opposite direction on a quiet back street in the airbag deployed halfway through and blew up in my face, causing my hands to be hurt and difficulty with breathing.
- Forward collision avoidance › Warnings · Lane departure › Blind spot detection
Collision Prevention Assist Plus Inoperative Light on the dashboard it appears often and beep I am not sure and why
- Visibility
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the sunroof panel was tilted on one side and fractured. There were no warning lights illuminated. Upon researching the failure, the contact associated the failure with NHTSA Campaign Number: 19V918000 (Visibility); however, the…
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the sunroof panel was tilted on one side and fractured. There were no warning lights illuminated. Upon researching the failure, the contact associated the failure with NHTSA Campaign Number: 19V918000 (Visibility); however, the VIN was not included. The vehicle was taken to the local dealer, who confirmed there was no recall coverage on the VIN for the failure. The dealer provided an unknown diagnosis. The vehicle was not repaired. The manufacturer was contacted and confirmed that the VIN was not under recall. The failure mileage was approximately 85,000.
- Structure › Body › Roof and pillars
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the roof panel had detached and was tilted. The vehicle was taken to the dealer, where an estimate for the repair was provided. The contact related the failure to NHTSA Campaign Number: 21V197000 (Structure), but the dealer…
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the roof panel had detached and was tilted. The vehicle was taken to the dealer, where an estimate for the repair was provided. The contact related the failure to NHTSA Campaign Number: 21V197000 (Structure), but the dealer informed the contact that the VIN was not included in the recall. The vehicle was not repaired due to the cost. The manufacturer was not notified of the failure. The failure mileage was approximately 98,000.
- Suspension
The contact owns a 2015 Mercedes-Benz GLA250. While the contact's daughter was driving at an undisclosed speed, the rear suspension collapsed. The contact stated that when the failure occurred, the vehicle swerved into the next lane. The contact stated that there were no other vehicles nearby…
The contact owns a 2015 Mercedes-Benz GLA250. While the contact's daughter was driving at an undisclosed speed, the rear suspension collapsed. The contact stated that when the failure occurred, the vehicle swerved into the next lane. The contact stated that there were no other vehicles nearby during the failure. The vehicle was towed to the dealer, where it was diagnosed with frame corrosion. The contact was informed that the frame needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 70,000.
- Structure › Body
Mercedes repair shop inspected this car and stated that there is rear-subframe rusting and corrosion. Repair shop states that this is a safety issue. I took it into Mercedes dealer who stated that this VIN is not covered by a 20-year, unlimited-mile rear-subframe warranty (Feb–Mar 2023) for…
Mercedes repair shop inspected this car and stated that there is rear-subframe rusting and corrosion. Repair shop states that this is a safety issue. I took it into Mercedes dealer who stated that this VIN is not covered by a 20-year, unlimited-mile rear-subframe warranty (Feb–Mar 2023) for specific models (C/E/GLK/CLS/SLK/SLC/SL). Mercedes extended the warranty on the models where they saw the most repeat failures, in a way that addresses the worst cases (holes) while controlling scope and liability—not an admission of a universal defect across all lines (e.g., GLA), which is why my VIN isn’t in the program.
- Air bags › Srs malfunction warning lamp/light · Steering
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that while driving at an undisclosed speed, the SRS warning light illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the steering control module. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 180,000.
- Engine
The contact owns a 2015 Mercedes-Benz GLA 250. The contact stated that occasionally, while driving at various speeds, the vehicle experienced a loss of automotive power. The check engine warning light was illuminated. The contact stated that the failure had progressed. The vehicle was taken to a…
The contact owns a 2015 Mercedes-Benz GLA 250. The contact stated that occasionally, while driving at various speeds, the vehicle experienced a loss of automotive power. The check engine warning light was illuminated. The contact stated that the failure had progressed. The vehicle was taken to a local independent mechanic, where it was diagnosed and DTC: P052E71; was retrieved. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The contact related the failure to an undisclosed recall; however, the VIN was not included. The manufacturer was made aware of the failure. The failure mileage was approximately 90,000.
- Engine · Fuel/propulsion system
Check engine light on my 2015 MB GLA250 4matic came on and the error is "P052E PCV Regulator Valve Performance". There is a recall for other MB vehicle with the same engine. I believe the 2015 Mercedes-Benz GLA250 and other models with the same engine should be included in the recall.
- Engine
I have a 2015 Mercedes benz GLA 250 showing code P052E There’s a TSB (MC‑10241531‑0001) and (LI01.20-P-076894 )covering intake‑line assemblies on similar M270‑engine models. Based on these two service bulletin kindly assist with extended emissions warranty
- Fuel/propulsion system
Same part had been recalled from all other models but not my model. It's the same part being used across Mercedes and they won't sale the valve and force customers like me there are thousands other to spent $2700 plus to replace whole system. Should have been recalled since it's same valve that may be using across all vehicles. Failed the emission test which is a big problem they should have addressed.
- Fuel/propulsion system
They had recall of this part which is valve in all other models except for this one. My vehicle failed VEIP test due to faulty valve and required assistance from the dealer but they refused to provide solutions and asked to pay $2700 and $230 diagnosis fee when we already had code which showed…
They had recall of this part which is valve in all other models except for this one. My vehicle failed VEIP test due to faulty valve and required assistance from the dealer but they refused to provide solutions and asked to pay $2700 and $230 diagnosis fee when we already had code which showed which part and which is recalled in all other Mercedes vehicles with 150000 milage warranty. We cannot just replace valve they are forcing to replace whole assembly causing problems for many owners like me. My vehicle has only 36k milage. If same valve is faulty which creates environmental hazard that should be recalled in all models from same manufacturer Instead of forcing ripping customers with high cost and environmental risk.
- Fuel/propulsion system · Lane departure › Blind spot detection
Car smell like fuel possibly fuel injectors or fuel line… recall on 2016-2021 models but 2015 having same issue Blind spot assist says inoperative Mercedes changed sensors multiple times still says inoperative
- Power train · Visibility › Sun/moon roof assembly
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated while attempting to accelerate, the vehicle hesitated before accelerating. While driving at various speeds, the vehicle was lagging with a loud rumbling sound coming from the rear of the vehicle. The contact depressed the accelerator…
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated while attempting to accelerate, the vehicle hesitated before accelerating. While driving at various speeds, the vehicle was lagging with a loud rumbling sound coming from the rear of the vehicle. The contact depressed the accelerator pedal excessively to stop the vehicle from hesitating. The failure had become more persistent. The contact stated that the sunroof failed to open, as well. There were no warning lights illuminated. The vehicle had not been taken to the dealer. The vehicle had not been diagnosed. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was 133,277.
- Engine
Today a Check Engine Light turned on my vehicle. I pulled the code via the OBD2 port and looked it up online. It turns out that this issue, code P052E, a defective Crankcase Ventilation Regulator Valve, is a well known problem on in-period MB cars and the manufacturer has issued an extended…
Today a Check Engine Light turned on my vehicle. I pulled the code via the OBD2 port and looked it up online. It turns out that this issue, code P052E, a defective Crankcase Ventilation Regulator Valve, is a well known problem on in-period MB cars and the manufacturer has issued an extended warranty to other models in their range, but excluded the GLA250, which uses the same parts as several other covered models including the GLC300, a vehicle covered by said extended warranty. If left untreated oil can travel up the electronic lines, ultimately fouling the ECU leading to an extreme hazard. This fault is also extremely expensive to fix, about $2000, as the faulty part (alone about $70) is sold only as a component of a larger kit (about $700), and installing the kit requires removing motor mounts and hoisting the engine. Mercedes should either widen the Extended Warranty to cover all of it's vehicles built with the defective part or issue a recall.
- Engine · Power train · Unknown or other
Good Afternoon, the status of my vehicle is simply UNKNOWN. I purchased my vehicle on the 26th last year of January. That same day I drove it back home my car was jerking. So I went back the following day to see if I could get into another vehicle because this one was malfunctioning they didn’t…
Good Afternoon, the status of my vehicle is simply UNKNOWN. I purchased my vehicle on the 26th last year of January. That same day I drove it back home my car was jerking. So I went back the following day to see if I could get into another vehicle because this one was malfunctioning they didn’t want to do anything for me. I tried so many different options to get out of this car I had a few scares driving this car the week of ownership. About sis times my car cut off completely during traffic and I have some recorded videos. Theirs a leakage somewhere I can fill up my gas tank to full and drive maybe two blocks away from my house and the gas meter is say that I have half a tank. Now my car is overheating, it’s not cranking it just tells me on the dashboard that 4MATIC is unavailable.
- Structure · Visibility › Sun/moon roof assembly
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the sunroof failed to close completely as needed. Upon inspection, the contact discovered that a plastic part of the roof panel had detached. The vehicle was taken to an independent mechanic, who replaced the right and left roof…
The contact owns a 2015 Mercedes-Benz GLA250. The contact stated that the sunroof failed to close completely as needed. Upon inspection, the contact discovered that a plastic part of the roof panel had detached. The vehicle was taken to an independent mechanic, who replaced the right and left roof guides, motor glass, and headliners. The contact related the failure to NHTSA Campaign Number: 23V854000 (Structure); however, the VIN was not included in the recall. The manufacturer was made aware of the failure. The failure mileage was approximately 120,000.
- Power train
there is a known issue with the mercedes benz GLA 250 rear differential. it is defective and need to be replaced many times during the life of the vehicle. i have not had an accident that i can relate to this defect but i feel it need to be reported and investigated by your office. the cost of…
there is a known issue with the mercedes benz GLA 250 rear differential. it is defective and need to be replaced many times during the life of the vehicle. i have not had an accident that i can relate to this defect but i feel it need to be reported and investigated by your office. the cost of the repair is over $6000. you can read more about this issue in this forum [XXX] i started reporting the issue before the warranty expired, the dealer was never able to find the problem, after the warranty expires they "discovered" what the issue is, the rear differential need to be replaced. of course they deny any wrongdoing but this is a well documented manufacturing defect that should be addressed. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Power train
Rear differential has failed/malfunctioned. The vehicle is available upon request. It is a road safety issue as it will stall/ hesitate when accelerating and has a jerking effect. It has been confirmed by an independent service center. It had not been inspected by anyone, other than an independent service center mechanic. There were no warning lamps, messages or other symptoms of the problem prior to the failure.
- Power train
The contact owns a 2015 Mercedes-Benz GLA250. While the contact’s daughter was driving approximately 35 MPH, the vehicle lost automotive power and stalled. The vehicle was eventually restarted and driven to the local dealer who diagnosed that the transmission valve body and conductor plate had…
The contact owns a 2015 Mercedes-Benz GLA250. While the contact’s daughter was driving approximately 35 MPH, the vehicle lost automotive power and stalled. The vehicle was eventually restarted and driven to the local dealer who diagnosed that the transmission valve body and conductor plate had failed and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure. The failure mileage was 47,749.
- Engine
My 2015 Mercedes Benz GLA check engine light came on for error P052E Positive Crankcase ventilation assembly. This is a $2,000 dollar repair because you need to buy the whole assembly and you can’t just buy the valve like other cars. This part has a recall on other models but not the GLA. For…
My 2015 Mercedes Benz GLA check engine light came on for error P052E Positive Crankcase ventilation assembly. This is a $2,000 dollar repair because you need to buy the whole assembly and you can’t just buy the valve like other cars. This part has a recall on other models but not the GLA. For example the metrics uses the same part and is covered by a recall but not the GLA. We need to included in this recall. This design flaw renders my 2015 useless and virtually has no value. Please compel Mercedes to recall this defective part and design flaw that requires 6-8 hours of labor for a simple part that is easily accessible on all other cars.
- Unknown or other
My car suddenly shifts to Neutral when stopped at the stoplight/while driving causing a safety issue. I had to turn off and turn on every time this happens. I called Mercedes and filed a complaint #06552876
- Forward collision avoidance › Automatic emergency braking · Forward collision avoidance › Warnings · Fuel/propulsion system
Engine Light Came up & CollIsion Warring Massage Show Up
- Engine
The engine light is one and the related code for the engine light is P052E-71. The valve for Crankcase ventilation has a malfunction. There is recall for the code for other Mercedes Benz car model varies from 2015 to 2019. I believe this code on for GLA 250 is the same manufacture malfunction parts and should be recalled for free replacement for safety reason.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003785Complaint Noise can be heard coming from the air conditioning system at higher blower motor speeds. Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Remove any leaves/foreign objects from the blower and interior air filter (the blower does NOT need to be replaced). After this, more fine-grained grilles and sealing frames can be used that are better at filtering out leaves / foreign objects. Parts required for retrofitting: Sealing frame (A 247 835 12 00) Sealing frame (A 247 835 11 00) Plug-in mounting (A 000 991 56 04) Housing cover (A 247 830 95 03) Housing cover (A 247 830 63 03) Steps: 1- Remove windshield wiper as per the work instructions AR82.30-P-0001MFA 2- Remove cover for water drain as per the work instructionsAR83.10-P-1411MFB 3- Release threaded connections (5x 10 mm, 2x 8 mm) 4- Fasten released part temporarily using cable tie to hood. 5- Thoroughly clean body between fender and wiper motor then mount the sealing frame (A 247 835 12 00) using the self-adhesive tape. 6- Cut cable tie and insert plastic part again. Then thoroughly clean the area behind the mounted sealing frame. 7- Open plastic cap on firewall then vacuum the filter using a vacuum cleaner. Then tighten the threaded connections again. 8- Finally, insert sealing frame (A 247 835 11 00) and attach to body-in-white using plug-in mounting (A 000 991 56 04) 9 - Clean water drains. 10- Assemble in reverse order. 11- Place housing cover (A 247 830 95 03) and housing cover (A 247 830 63 03) on top of each other.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10246281Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Various causes Up to Model year 2018 Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the guided test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. If fault code P06DA00 is activating the check engine light, update software of the ME control unit. No further repairs needed if the code no longer activates check engine light after 2 drive cycles. Model year 2019 and later Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10235988This service campaign has been initiated because Daimler AG (DAG) has determined that the preservation agent at the lower door hinges at the front and rear as well as at the lift-gate hinges may not correspond to specifications. As a result, it is possible that corrosion may form at the lower door hinges at the front and rear as well as at the hinges of the lift-gate. To remedy this situation an authorized Mercedes-Benz Dealer will apply preservation agent during the next workshop visit.
- 10219265Complaint Vibrations in steering at speeds lower than 30 mph. Possible when turning and also partly noticeable after changing to winter or all-season tires. Cause Controller stability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Remedy Software update available in 1st quarter of 2023 (adaptation of stability limits)
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205154Gasket may settle causing a slight oil leak.
- 10205143Clacking noises from the front axle area.
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179907Engine diagnosis warning lamp activated - Fault code P012800
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10169599Squeaking Noise from Exhaust Gas Flap
- 10167000Surface damage on steering wheel trim
- 10165847Diverse fault messages in instrument cluster. Distronic, ESP, tire pressure monitoring, engine indicator lamp Diverse CAN communication errors stored in quick test Possible malfunctions in Parktronic or Active Parking Assist. Possible malfunctions of PTC heater booster.
- 10160735Update restraint system control unit software
- 10160622Audio 20: Apple CarPlay displays pixelated image
- 10158365Reversing camera nonfunctional on vehicles with code 805 YoM 14/1 (MY15)
- 10158322Cracking noise at limit stop of electric steering
- 10158288Noises Made by M133 Exhaust Gas Flap
- 10158267COMAND Online: Some contacts on the telephone are not found via voice control.
- 10158250Garmin MAP PILOT: Traffic information service and possibly voice control inoperative after navigation software update using Download Manager version 2.0.29 or 2.0.30
- 10158236Instrument cluster: Always boots in main menu (trip/total mileage) / Last mode inoperative
- 10158209Instrument panel noises in area of instrument cluster faceplate in BR 117 / 156 / 176
- 10158199Vehicle does not start, battery discharged.
Every Mercedes-Benz Gla 250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.