2021 Mercedes-Benz Gla 250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Gla 250 › 2021
These records cover every 2021 Mercedes-Benz Gla 250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2021 Mercedes-Benz Gla 250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 CLA, 2019-2022 A-Class, 2022-2023 C-Class, 2024 CLE, 2020-2026 GLA/GLB, and 2023-2024 GLC vehicles. Please refer to MBUSA's recall report for specific model information. The micro-switch in the driver's door lock may corrode and fail to detect an open door, preventing the electronic parking brake…
Risk and remedy
Risk
A vehicle rollaway increases the risk of a crash or injury.
Remedy
Dealers will replace the driver's door lock, free of charge. Owner notification letters are expected to be mailed September 18, 2026. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Owners may contact MBUSA customer service at 1-800-367-6372. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning July 31, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2020 A220, 2020 CLA250, GLB250, AMG A35, AMG CLA45, AMG CLA35, and 2021 GLA250 vehicles. The vehicles may not be equipped with an inspection gauge to check the wear of the rear brake pads. In addition, information for using this inspection gauge might not be included in the owner's manual. As such…
Risk and remedy
Risk
Driving with worn brake pads can reduce braking ability, increasing the risk of a crash.
Remedy
Dealers will install an inspection gauge and provide supplemental owner's manual information, free of charge. Owner notification letters were mailed on February 29, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 AMG CLA 35 and 2021 GLA 250 vehicles. The rear brake caliper housing fasteners may be loose, which can reduce brake performance or cause rear brake components to detach from the vehicle.
Risk and remedy
Risk
Reduced brake performance can increase the risk of a crash. In addition, detached brake components can create a road hazard, and increase the risk of a crash for other drivers.
Remedy
Dealers will inspect and tighten the fasteners on the rear brake caliper housings, as necessary, free of charge. Owner notification letters were mailed March 25, 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain GLA250 vehicles. The ground connection for the front passenger air bag may not be mounted properly, which could result in an inadvertent deployment.
Risk and remedy
Risk
Inadvertent air bag deployment can increase the risk of injury for an occupant in the front passenger seat, and increase the possibility of a vehicle crash.
Remedy
MBUSA will notify owners, and dealers will inspect the ground connection for the passenger air bag and correct it, if necessary, free of charge. The recall began March 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020037.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2019 C300, E300, 2018-2020 CLA250, 2020 CLS450, AMG E53, AMG GT53, GLE450, 2018 AMG E63, AMG GTA, 2017-2020 GLA250, GLC300, 2019 GLC350, AMG GLC43, 2017-2018 GLE350, 2019 AMG GLC 43, GLC350, GLE400, 2017 GLS450, S550, C300 Cabrio, and 2018-2019 S560 vehicles. On June 18, 2021, an additional 9…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting emergency services through the call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the communication module and activate it, if necessary, free of charge. The recall began March 31, 2021. Letters for the owners of the 9 additional vehicles were mailed July 9, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021030005.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Owner complaints
18 complaints1 involved a crash2 injuries
What owners report most
Latest complaints
- Latches/locks/linkages
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 26V481000 (Latches/Locks/Linkages); however, the part to do the recall repair was not yet available. The local dealer was contacted by the manufacturer. The contact stated that the manufacturer…
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 26V481000 (Latches/Locks/Linkages); however, the part to do the recall repair was not yet available. The local dealer was contacted by the manufacturer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
- Engine and engine cooling · Power train
See attached document for complaint
- Electrical system · Engine · Structure › Body
Cowl vent grille openings allowed normal environmental debris to accumulate, plug drainage and divert water onto electrical components and potentially result in a fire if not addressed. Some of the debris passes through into the hvac system and cannot be cleaned without dealer removal/repair of…
Cowl vent grille openings allowed normal environmental debris to accumulate, plug drainage and divert water onto electrical components and potentially result in a fire if not addressed. Some of the debris passes through into the hvac system and cannot be cleaned without dealer removal/repair of the hvac motor, which costs the customer more than $500 in repairs and disincentivizes mitigation. Furthermore, Mercedes is aware of the problem, has not issued a customer satisfaction recall, and instead, is charging customers more than $1,000 to install a plastic protective shield to prevent accumulation of debris, clogged water management, and risk of fire.
- Fuel/propulsion system · Unknown or other
The Gas Door did not open in order to pump gasoline. There is no mechanical device for the driver, passenger, owner of the vehicle to manually open the gas door from the inside. There was no electronic warning within the Mercedes Benz to alert driver about malfunction of gas door not working.…
The Gas Door did not open in order to pump gasoline. There is no mechanical device for the driver, passenger, owner of the vehicle to manually open the gas door from the inside. There was no electronic warning within the Mercedes Benz to alert driver about malfunction of gas door not working. Driver took vehicle to local Firestone mechanic who said the "gas door actuator" needed to be replaced. Accordingly, vehicle with the remaining gasoline was taken to local Mercedes Dealer who after the vehicle being looked at, "confirmed gas door to not opening due to internal mechanical fault" and replaced with new gas door actuator at a cost of $820.28. Vehicle owner mentioned to service rep, that he lives from parents about 150 miles away and had the vehicle owner stopped at gas station in between, the vehicle owner would have been stranded without any access to a dealer to fix this critical safety issue. Vehicle owner then advised service rep this issue should have been elevated as critical safety recall issue and that a complaint would be filed with NHTSA. Any vehicle owner, their family if being transported in a deserted place hoping to go to the next gas station for pumping gas would have faced a severe danger to their self and their families. Vehicle owner has sent a detailed letter to Mercedes Benz corporate office in USA detailing the incident and a copy of the letter will be attached as an attachment if it is permitted in this complaint. Requesting a recall of this issue with an order for reimbursement of service charges paid by vehicle owners to fix this "malfunction of gas door". There are multiple complaints to this effect on various message boards regarding the occurrences of "gas door not opening". This also needs to be looked at.
- Engine · Fuel/propulsion system · Vehicle speed control
When coming to a full stop at a red light (or any need to idle at a stop), the car frequently begins to hesitate as if it is about to cut off. I assume it has something to do with the ‘fuel saving feature’ which comes on in the form of a green symbol in the lower left of the odometer display (the…
When coming to a full stop at a red light (or any need to idle at a stop), the car frequently begins to hesitate as if it is about to cut off. I assume it has something to do with the ‘fuel saving feature’ which comes on in the form of a green symbol in the lower left of the odometer display (the engine is still running the AC) . When you start to drive again the car always jerks before moving , on at least 3 occasions it has actually cut off completely and must be restarted (everything goes off) - it is big problem, especially in heavy traffic (horns blaring & angry drivers are encountered) I almost had a car hit me from behind; my car had jerked slightly when I began to accelerate and then shut off completely. It is definitely a dangerous defect. The Dealership emphasizes 93 Octane gas or higher to help with this issue- but I Always use the highest Octane gas I can find ! It has happened VERY often - I dread stopping at red lights and stop signs, one day it will cause an accident.
- Engine · Unknown or other
I am reporting a potential safety and mechanical defect involving the cylinder head in the Mercedes-Benz GLA 250. Many owners, including myself, have experienced premature cylinder head failure, often without warning, leading to loss of power, engine misfires, rough idling, and in some cases…
I am reporting a potential safety and mechanical defect involving the cylinder head in the Mercedes-Benz GLA 250. Many owners, including myself, have experienced premature cylinder head failure, often without warning, leading to loss of power, engine misfires, rough idling, and in some cases, sudden engine shutdown while driving. This issue appears to be widespread among GLA models equipped with the M260/M270 engine, often occurring well before 100,000 miles. It raises serious concerns about the design, durability, and safety of the engine’s top-end components. Given the frequency and severity of this failure — and the high cost of repairs — I believe this warrants an official investigation and potential manufacturer recall. I urge the NHTSA to review similar complaints and initiate a formal inquiry into Mercedes-Benz’s awareness and handling of this defect. Thank you for your attention to this matter.
- Latches/locks/linkages › Hatchback/liftgate › Lock
Twice now, my husband is putting groceries in the back of the vehicle and the top closes on him and this last time, hit him hard in the head. This is a safety issue, what can we do??
- Unknown or other
My vehicle has two separate tire inflation placards. There is a placard inside the drivers door recommending 43 PSI (cold) all tires, and another placard inside the fuel door recommending 38 PSI front and 34 PSI rear (cold). Two different tire service centers have confirmed that my tires are…
My vehicle has two separate tire inflation placards. There is a placard inside the drivers door recommending 43 PSI (cold) all tires, and another placard inside the fuel door recommending 38 PSI front and 34 PSI rear (cold). Two different tire service centers have confirmed that my tires are wearing out prematurely because of overinflation. My telephone calls to Mercedes USA have been handled poorly because their representatives are poorly training and do not understand the nature of my issue.
- Engine
Engine misfired in operation requiring an emergency stop while on a mountain road. Severe check engine light turned on (Mercedes has a two stage check engine light). Vehicle was parked for 20 minutes and battery was disconnected. This appeared to fix the issue. Vehicle was brought to dealer.…
Engine misfired in operation requiring an emergency stop while on a mountain road. Severe check engine light turned on (Mercedes has a two stage check engine light). Vehicle was parked for 20 minutes and battery was disconnected. This appeared to fix the issue. Vehicle was brought to dealer. Dealer stated the cylinder head for early 2021 GLA 250 engines had a casting flaw that result in hot gases escaping and damaging engine. Engine and turbo rebuilt under warranty at 17000 miles.
- Electrical system
The entire circuit board was short circuited immobilizing the car in the middle of the highway. It was determined that the condensation of the air conditioning was unable to drain due to the drainage tubing being clogged with insects, causing water to back up and short circuited the electrical system.
- Engine · Fuel/propulsion system
I purchased this car approx 3 months after real issues began. My car would have issues idling where it would sometimes turn off at stop lights and require multiple reignition attempts before proceeding. This would also happen when the auto-start feature (anti-idle/gas saving) was engaged (which is…
I purchased this car approx 3 months after real issues began. My car would have issues idling where it would sometimes turn off at stop lights and require multiple reignition attempts before proceeding. This would also happen when the auto-start feature (anti-idle/gas saving) was engaged (which is the default in the system) and this posed major safety concerns. The unstable idling of the car would result in an initial acceleration after being stopped, shortly followed by the engine dying. There were multiple times I was at an intersection yielding before turning where this happened and it resulted in my being in the path of oncoming traffic without the ability to accelerate until the car restarted. I contacted my local Mercedes dealer who acted like this wasn't a big deal, but it is related to a known issue with a faulty cylinder head. They covered the repair under the manufacturer warranty, but told me to keep driving my car and promised it was safe until they could get the part in (because the didn't have a loaner car to provide). I found this very troubling. In conversations throughout the repair being completed, the dealer admitted that they know the part that was used for the year and model is bad, but they didn't want to do a recall and would wait for issues to come up. This is unacceptable because this absolutely is a safety concern as demonstrated by the example I shared. They should be required to do a full recall to address the safety concerns and I believe not disclosing this information was unfair to me as a consumer who did not have the information I needed to be informed on the reliability of this vehicle prior to purchase.
- Back over prevention · Electrical system
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System) however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet…
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System) however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
- Tires
The contact called on behalf of his client who owns a 2021 Mercedes-Benz GLA250 equipped with Continual tires, Tire Line: Procontact GXSSR, Tire Size: 235/55r/18, and DOT 6y3lwxx43220. The contact stated while driving at 30 MPH on a local road and attempting to get into the right lane, the driver…
The contact called on behalf of his client who owns a 2021 Mercedes-Benz GLA250 equipped with Continual tires, Tire Line: Procontact GXSSR, Tire Size: 235/55r/18, and DOT 6y3lwxx43220. The contact stated while driving at 30 MPH on a local road and attempting to get into the right lane, the driver crashed into a pole where the vehicle came to a stop. The contact suffered injuries to the face from the air bag deploying and hurt her leg. No medical attention was needed. There was no warning light illuminated. The vehicle was towed to an impound lot. The manufacturer was made aware of the failure. The failure mileage was 11,000.
- Tires
I have a zero point dmv clean record!! Tires are dysfunctional poorly made235/55 R18 The front tires are ready to blow out and look /feel very unsafe to drive no blow out yet - however last 6 months many people have noticed POOR TRACTION & asked if the car tires need air. No air WAS NEEDED!!…
I have a zero point dmv clean record!! Tires are dysfunctional poorly made235/55 R18 The front tires are ready to blow out and look /feel very unsafe to drive no blow out yet - however last 6 months many people have noticed POOR TRACTION & asked if the car tires need air. No air WAS NEEDED!! Continental offered 40% off for replacement tires. This is unacceptable ! These are not industry safe and continental stated there’s no mileage warranty! Who gets all new tires at 26,500 miles. I’m a mom going to the grocery store and the mall! My brand new 2021 leased Car now has approx. 26,500 miles . Bought October 2020! Front tires are near bald. Back tires are nearly worn as well. Car was in & serviced at Mercedes’ where point inspections prove NO ALIGNMENT ISSUES 04/2022 and prior service dates tires were rotated 4 times and all service schedules were completed! Assumptions were made that I didn’t rotate tires as exscuse for POORLY MADE an outlet for UNSAFE TIRES. I live in a mild climate, Nor Cal and went to the snow one time. No car accidents, no beach salt climate. Also the Car is parked IN A covered garage area no excessive temps ON THE tires. No off roading. I have never seen a car tire wear like this. Colors been brown murky also continues alwaysneeds polish !!It’s not the Industry standard. It drives choppy also and reflects no air needed! For a Run flat expensive tire there’s no reason why it’s such a piece of junk. I’m middle aged and not a teenage driver this should of lasted ! Bought my car brand new nearly 50 grand Mercedes 2021! This is my 6th Mercedes’ and second leased Mercedes’ I’ve owned Escalade, 2 bmws, fiat, sabb, ml500 Mercedes’ , cla250 lease before this one that 2018 I got 40,000 miles only changed 2 tires due too moderate driving.
- Power train
I was parked in a lot and turned the ignition on and selected "DRIVE" but when I started to pull away the vehicle went backwards instead of forwards (as though "REVERSE" had been selected). I switched back to PARK, then selected DRIVE again and the vehicle once again went backwards. I then turned…
I was parked in a lot and turned the ignition on and selected "DRIVE" but when I started to pull away the vehicle went backwards instead of forwards (as though "REVERSE" had been selected). I switched back to PARK, then selected DRIVE again and the vehicle once again went backwards. I then turned the engine off altogether and restarted it and this seemed to clear up the problem as now the vehicle went forwards when in DRIVE. No damage, or injuries, but of course very concerning from a safety point of view which is why I am reporting this. Mercedes did check the vehicle out the next day and could not locate any problem.
- Forward collision avoidance › Automatic emergency braking · Service brakes
Car's brake system slammed on in light traffic with no nearby obstacles. Clear night, light traffic, road dry, moderate temperature. If there had been more traffic, or if the road had been slick, high probability of risk. Dealer has been notified, will not be able to pick up vehicle for a day or two. I did not see any warning lights, heard no warning sounds.
- Back over prevention · Electrical system
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the…
The contact owns a 2021 Mercedes-Benz GLA250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the rearview camera image was not displaying on the display screen. The vehicle was taken to the dealer, but the dealer could not activate the display screen and informed the contact that they were waiting for parts to arrive to perform the repair. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 2,200.
- Unknown or other
Please fix issue associated with my vin so I can Turo it
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009518Complaint Lower rear door cover protrudes in area of rear wheel arch. Left and right vehicle side could be affected. See Figure 1 Cause Rear catch tab of the rear door cover cannot fully engage, causing the component part to protrude. Remedy Order new component part and, before installing the new part, shorten the contact ribs on the rear catch tab by 1 mm (A). See Figure 2.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005288Complaint Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, 247476 247747, 247646 247647 the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, 247751 247753, 274651 the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part.
- 11003785Complaint Noise can be heard coming from the air conditioning system at higher blower motor speeds. Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Remove any leaves/foreign objects from the blower and interior air filter (the blower does NOT need to be replaced). After this, more fine-grained grilles and sealing frames can be used that are better at filtering out leaves / foreign objects. Parts required for retrofitting: Sealing frame (A 247 835 12 00) Sealing frame (A 247 835 11 00) Plug-in mounting (A 000 991 56 04) Housing cover (A 247 830 95 03) Housing cover (A 247 830 63 03) Steps: 1- Remove windshield wiper as per the work instructions AR82.30-P-0001MFA 2- Remove cover for water drain as per the work instructionsAR83.10-P-1411MFB 3- Release threaded connections (5x 10 mm, 2x 8 mm) 4- Fasten released part temporarily using cable tie to hood. 5- Thoroughly clean body between fender and wiper motor then mount the sealing frame (A 247 835 12 00) using the self-adhesive tape. 6- Cut cable tie and insert plastic part again. Then thoroughly clean the area behind the mounted sealing frame. 7- Open plastic cap on firewall then vacuum the filter using a vacuum cleaner. Then tighten the threaded connections again. 8- Finally, insert sealing frame (A 247 835 11 00) and attach to body-in-white using plug-in mounting (A 000 991 56 04) 9 - Clean water drains. 10- Assemble in reverse order. 11- Place housing cover (A 247 830 95 03) and housing cover (A 247 830 63 03) on top of each other.
- 11000596Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.
- 11000541Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10253715Check engine light active and FC P146364 Temp. and pressure sensor B4/7 is stored in Engine control unit and Fuel pump control unit. Software parameter in Fuel pump control unit. Perform software update for Fuel System Control Module (FSCM) N118. New software is A0009026661.
- 10253708In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10253706IMPORTANT EMISSION EXTENDED WARRANTY INFORMATION In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the Fuel System Control Module (FSCM) software in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the FSCM software for the fuel pressure sensor and fuel temperature plausibility check may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ("MIL") might illuminate. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P146264 The sensor Low fuel pressure and fuel temperature has a malfunction. There is an implausible signal. -and/or- P146364 This error code can be ignored and erased. 'OR' Sensor Low fuel pressure and fuel temperature has a malfunction during calculation of the fuel pressure. There is an implausible signal. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 47045 90 Control Unit, Fuel Pump - Software Parts (Software): A0009026661 Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty. No part replacement is covered by this extended warranty.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10251118After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
- 10249731Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2021 GLA and GLB (247 platform) vehicles, the identification plate on the B-pillar does not correspond to current specifications.MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the identification plate on the B-pillar.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249537Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
Every Mercedes-Benz Gla 250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.