2020 Mercedes-Benz Glb 250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Glb 250 › 2020
These records cover every 2020 Mercedes-Benz Glb 250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
20 recalls name the 2020 Mercedes-Benz Glb 250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 CLA, 2019-2022 A-Class, 2022-2023 C-Class, 2024 CLE, 2020-2026 GLA/GLB, and 2023-2024 GLC vehicles. Please refer to MBUSA's recall report for specific model information. The micro-switch in the driver's door lock may corrode and fail to detect an open door, preventing the electronic parking brake…
Risk and remedy
Risk
A vehicle rollaway increases the risk of a crash or injury.
Remedy
Dealers will replace the driver's door lock, free of charge. Owner notification letters are expected to be mailed September 18, 2026. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Owners may contact MBUSA customer service at 1-800-367-6372. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning July 31, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2020 A220, 2020 CLA250, GLB250, AMG A35, AMG CLA45, AMG CLA35, and 2021 GLA250 vehicles. The vehicles may not be equipped with an inspection gauge to check the wear of the rear brake pads. In addition, information for using this inspection gauge might not be included in the owner's manual. As such…
Risk and remedy
Risk
Driving with worn brake pads can reduce braking ability, increasing the risk of a crash.
Remedy
Dealers will install an inspection gauge and provide supplemental owner's manual information, free of charge. Owner notification letters were mailed on February 29, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 AMG GLB35, 2019-2020 A220, and 2020 GLB250 vehicles. The integral carrier that supports the front axle may corrode, causing it to fail.
Risk and remedy
Risk
Front axle carrier failure may result in a loss of steering control, increasing the risk of a crash.
Remedy
Dealers will inspect and replace the integral carrier, as necessary, free of charge. Owner notification letters were mailed July 29, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022070009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source, such as hot engine or exhaust components, can increase the risk of a fire.
Remedy
Dealers will replace the fuel rail and fuel injectors, free of charge. Owner notification letters were mailed April 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030003.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLB250 vehicles. In the event of a crash, the air bag control unit software may not activate the front seat belts and front passenger air bag properly.
Risk and remedy
Risk
Air bags and seat belts that do not function properly can increase the risk of injury in a crash.
Remedy
Dealers will update the air bag control unit software, free of charge. Owner notification letters were mailed on September 17, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLB 250 vehicles. The accessory power outlet for the second-row seating may have excessive voltage due to an incorrect voltage converter socket.
Risk and remedy
Risk
Excessive voltage through the accessory power outlet to a connected device can increase the risk of a fire.
Remedy
Dealers will inspect and replace the voltage converter, as necessary, free of charge. Owner notification letters were mailed on September 3, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021080005.
Mercedes-Benz LLC (MBUSA) is recalling certain 2018-2020 C300, 2019-2020 A220, AMG C43, AMG C63, 2020 GLE580, GLB250, 2020-2021 GLE450, GLE350, 2021 AMG GLE63, and AMG GLE53 vehicles. The LED headlights may have been incorrectly adjusted during a vehicle repair. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety…
Risk and remedy
Risk
Incorrectly adjusted headlights may reduce visibility, increasing the risk of a crash.
Remedy
Dealers will replace the LED headlights, free of charge. Interim letters notifying owners of the safety risk were mailed August 13, 2021. A second notice will be sent once the remedy is available. Owner notification letters were mailed January 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLB250 vehicles. Water may enter through the wheel well area into the front occupant foot wells, potentially damaging certain electrical components. This may result in the instrument cluster going blank, an engine stall while driving, or the vehicle may not start.
Risk and remedy
Risk
Either a blank instrument cluster display or an engine stall can increase the risk of a crash.
Remedy
Dealers will seal the vehicle body in the wheel well area and inspect the front foot wells for water intrusion, repairing as necessary, free of charge. Owner notification letters were mailed July 20, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020070009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLB250 vehicles. The side curtain air bags may not deploy properly during a crash.
Risk and remedy
Risk
Air bags that do not deploy as intended can increase the risk of injury.
Remedy
Dealers will replace the side curtain air bags, free of charge. Owner notification letters were mailed on September 24, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020 GLB250 vehicles. The front passenger air bag inflator and cushion may be improperly attached inside the air bag module, which could result in the air bag cushion tearing upon deployment.
Risk and remedy
Risk
An air bag that does not deploy properly during a crash can increase the risk of injury.
Remedy
Dealers will replace the front passenger air bag module, free of charge. Owner notification letters were mailed July 16, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021060011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLB35 AMG, and 2020-2021 GLB250 vehicles. The side spoilers on the tailgate might not have been installed correctly, allowing them to detach.
Risk and remedy
Risk
Detached spoilers can create a road hazard, increasing the risk of a crash or injury.
Remedy
MBUSA will notify owners, and dealers will inspect and, if necessary, replace the side spoilers, free of charge. Owner letters were mailed July 2, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021050009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLB250 vehicles. The wheel arch covers on the front fenders might not have been installed correctly, allow them to detach.
Risk and remedy
Risk
Detached wheel arch covers can create a road hazard, increasing the risk of a crash or injury.
Remedy
MBUSA will notify owners, and dealers will check the installation of the front wheel arch covers and correct them as necessary, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLB 250 vehicles. The window air bag in the A-pillar area may not be mounted correctly, affecting its performance. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 226, "Ejection Mitigation."
Risk and remedy
Risk
In the event of a crash that deploys the window air bag, the catch strap could disconnect and increase the risk of injury.
Remedy
MBUSA will notify owners, and dealers will check the mounting of the window air bag and correct it as necessary, free of charge. The recall began October 30, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020100010.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLB250 vehicles. The second row seat may not be correctly aligned within the seat track on one side, possibly causing the seat to not lock properly into place.
Risk and remedy
Risk
If the second row seat is not locked into place, there could be an increased risk of injury to the seat occupants in a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the installation of the second row seat and correct it, if necessary, free of charge. The recall began October 23, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020090020.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLB250 vehicles. The rear spoiler above the tailgate may not have been welded correctly. This could result in parts of the spoiler detaching from the vehicle.
Risk and remedy
Risk
If the spoiler detaches while driving, it can become a road hazard, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the rear spoiler and replace it, if necessary, free of charge. The recall began October 23, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020090006.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2020 GLB 250 vehicles. Water may enter through the wheel well area into the front occupant foot wells, potentially damaging certain electrical components. This may result in the instrument cluster going blank, or an engine stall while driving without the ability to restart the vehicle.
Risk and remedy
Risk
Either a blank instrument cluster display or an engine stall can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will seal the vehicle body in the wheel well area and inspect the front foot wells for water intrusion, repairing as necessary, free of charge. The recall began July 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020070009.
Owner complaints
54 complaints3 involved a crash3 injuries
What owners report most
Latest complaints
- Electrical system · Structure › Body
SUBJECT: URGENT: Safety Recall Campaign 26V481 / XXX– Unreasonable Remedy Delay and Economic Hardship (VIN: [XXX]). I am formally logging a safety complaint regarding the unreasonable delay by Mercedes-Benz in providing a remedy for NHTSA Recall 26V481 (Mercedes Campaign XXX), affecting my vehicle…
SUBJECT: URGENT: Safety Recall Campaign 26V481 / XXX– Unreasonable Remedy Delay and Economic Hardship (VIN: [XXX]). I am formally logging a safety complaint regarding the unreasonable delay by Mercedes-Benz in providing a remedy for NHTSA Recall 26V481 (Mercedes Campaign XXX), affecting my vehicle (VIN: [XXX]). The manufacturer reported this critical defect to the NHTSA on XXX. Despite months having passed, and with owner notifications scheduled for XXX, the remedy remains unavailable. My local authorized dealerships (Mercedes-Benz of West Palm Beach and Delray) have canceled my service appointments, stating they have zero parts allocation from corporate and cannot perform repairs. This vehicle is a commercial asset utilized for peer-to-peer car sharing on the Turo platform. Because this recall involves a severe rollaway risk due to a defective door lock microswitch, Turo has automatically unlisted and deactivated my vehicle to comply with safety regulations. Mercedes-Benz’s failure to distribute parts is causing severe, compounding financial damages due to lost rental revenue, leaving me stranded with an unsafe vehicle that is legally and commercially inoperable. I request that the NHTSA intervene to hold the manufacturer accountable and expedite parts allocation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Latches/locks/linkages
The contact owns a 2020 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign: 26V481000 (Latches/Lock/Linkages); however, the part for the recall repair was not available. The contact stated that while attempting to Park the vehicle, the parking brake independently engaged. The…
The contact owns a 2020 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign: 26V481000 (Latches/Lock/Linkages); however, the part for the recall repair was not available. The contact stated that while attempting to Park the vehicle, the parking brake independently engaged. The ABS warning light was illuminated. The vehicle was taken to a local dealer and the failure was confirmed. The failure mileage was approximately 70,000.
- Power train · Steering · Suspension
I am submitting this complaint because I believe the repair performed under NHTSA Recall 21V990 / Mercedes-Benz Campaign 2022070009 in May 2024 failed to adequately correct the safety defect identified in the recall.When driving my axle snapped causing my tire to pop out and me to loose control of…
I am submitting this complaint because I believe the repair performed under NHTSA Recall 21V990 / Mercedes-Benz Campaign 2022070009 in May 2024 failed to adequately correct the safety defect identified in the recall.When driving my axle snapped causing my tire to pop out and me to loose control of the car causing a crash into the curb. I have since been without a vehicle with Mercedes Benz of Augusta denying my vehicle after having it towed. They refused to even look at it seeing the axle issue. The recall specifically states: “Mercedes-Benz AG has determined that on certain Model Year 2019–2021 A-Class and GLB-Class vehicles, the corrosion protection of the integral carrier of the front axle might not be sustained over the lifetime of the vehicle. Under specific environmental influences, corrosion of the integral carrier of the front axle might occur after several years. As a result, depending on the intensity and location of the corrosion, an impairment of the structural durability of the integral carrier as well as the connection to other components cannot be ruled out. In this case, vehicle steering might be affected which could potentially increase the risk of a crash.” My 2020 Mercedes-Benz GLB 250 received the recall repair in May 2024. Despite the recall repair being completed, the vehicle subsequently experienced a serious front-end/steering-related mechanical failure involving components connected to the front axle, resulting in an accident and loss of steering control.I am particularly concerned because the failure occurred in the same general front-axle area addressed by Recall 21V990, and the recall itself specifically identifies the possibility that deterioration of the integral carrier and its connections can affect steering and increase the risk of a crash.I am requesting that NHTSA investigate whether the May 2024 recall remedy was properly performed and whether the recall remedy adequately addresses the underlying safety defect in this vehicle.
- Engine · Fuel/propulsion system
Diagnostics performed and found electrical/component fault and possible wire damage to fuel pump. NECC to drain tank and inspect replace fule pump if necc. Oringally took one week prior and diagnostics led to the possiblility that the cylinder head was malfunctioning, which was a manufacturing defect and covered under an extended warranty, but now advised otherwise. Quote $2200.00. Mileage on vehicle 23,660.
- Structure › Body
I am submitting this formal complaint regarding a serious safety incident involving my 2020 Mercedes-Benz GLB, which directly reflects the defect outlined in Recall 20V-480 (Rear Spoiler Detachment). Although my VIN is not officially included in the affected range, the exact failure described in…
I am submitting this formal complaint regarding a serious safety incident involving my 2020 Mercedes-Benz GLB, which directly reflects the defect outlined in Recall 20V-480 (Rear Spoiler Detachment). Although my VIN is not officially included in the affected range, the exact failure described in the recall occurred on my vehicle. On or about June 16, 2025, at approximately 3:00 p.m., I was driving and I noticed an object in my rearview mirror that had become airborne and was causing vehicles behind me to swerve to avoid it. Moments later, two separate vehicles pulled up alongside me, and the drivers began waving their arms to get my attention. I exited the roadway and pulled into the Walmart parking lot, where a couple in a pickup truck approached me and informed me that the rear spoiler of my vehicle had flown off. I got out to inspect the vehicle, and indeed, the spoiler was completely gone. I returned to the area where I first saw the airborne object, attempting to locate the detached part, but was unsuccessful in recovering it. I contacted Mercedes-Benz USA and my local dealership on June 17, 2025, and was told that because my vehicle’s VIN is not listed under the recall, I would be responsible for the full cost of inspection and repair. Frankly, that position is unacceptable for the following reasons: - Recall 20V-480 describes a defect involving improperly welded rear spoilers on 2020 GLB250 models, which can detach while driving. That is exactly what happened to my vehicle under normal conditions. - The spoiler detached while the vehicle was in motion, creating a dangerous road hazard—just as outlined in the recall. - The vehicle has never been involved in a collision or sustained rear-end damage. It has not been subjected to outside interference. - My VIN has been included in at least five previous recalls, underscoring that my vehicle was part of broader quality issues during that production period.
- Structure › Body
See attached document for complaint.
- Equipment · Service brakes, hydraulic
The contact owns a 2020 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign Number: 23V732000 (Service Brakes, Hydraulic, Equipment); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of…
The contact owns a 2020 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign Number: 23V732000 (Service Brakes, Hydraulic, Equipment); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
- Suspension
Front and rear suspension/control arms appears to have squeaky noises when approaching a turn or going a speed bump.
- Steering · Suspension · Wheels
CV joint axle. This car does not maintain its lane. Drives misaligned and sounds like there is a cracking noise like something is breaking under driverside steering wheel. Attention assist comes on often. This issue appeared shortly after purchasing 05/24. The vehicle had been inspected multiple…
CV joint axle. This car does not maintain its lane. Drives misaligned and sounds like there is a cracking noise like something is breaking under driverside steering wheel. Attention assist comes on often. This issue appeared shortly after purchasing 05/24. The vehicle had been inspected multiple times by Mercedes. Supposedly there were looks bolts underneath that were tightened. Problem persists every-time vehicle is driven.
- Power train · Vehicle speed control
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while the vehicle was at a stop light, the accelerator pedal was depressed however, the vehicle lunged backward. There was no warning light illuminated. The contact depressed the brake pedal to stop the vehicle. The vehicle was…
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while the vehicle was at a stop light, the accelerator pedal was depressed however, the vehicle lunged backward. There was no warning light illuminated. The contact depressed the brake pedal to stop the vehicle. The vehicle was restarted; however, the failure recurred. The vehicle was taken to the dealer but was not diagnosed or repaired. The contact was informed by the dealer that the failure could not be duplicated. The manufacturer was made aware of the failure. The approximate failure mileage was 50,307.
- Engine
Car constantly cuts out and loses power as well as occasionally shuts off for no reason. Causing very hazardous driving conditions. I have noticed that this is a common issue stated in online forums with this particular car as well. It is more times than not an issue with the engine head and valves.
- Structure › Body › Hatchback/liftgate
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while driving 45 MPH, the rear spoiler detached from the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was determined that the spoiler needed to be replaced. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 47,000.
- Unknown or other
Power Liftgate (via key fob – SmartKey). Mercedes GLB250. Was told by Mercedes employees that all cars operate the same. oSensor that automatically stops liftgate if it detects an obstruction does not retract to allow someone reaching in the trunk to safely exit the trunk. oThe liftgate stops, but…
Power Liftgate (via key fob – SmartKey). Mercedes GLB250. Was told by Mercedes employees that all cars operate the same. oSensor that automatically stops liftgate if it detects an obstruction does not retract to allow someone reaching in the trunk to safely exit the trunk. oThe liftgate stops, but it does not do so until it has hit/touched the objection or obstruction. oWhen you press the trunk button on the key fob, the liftgate only raises slightly (maybe 2 inches). oIf you press the key fob again, the liftgate just continues to go up and down within those few inches and continues to hit/touch the object/obstruction each time you press the button. Half of my body was trapped in the trunk. Suffered injury to shoulder and hand. oI was taking grocery bags out of the trunk and had the key fob in my pocket. oAn item fell out of the bag so I reached into the trunk to grab it. oAs I leaned in, the body of the car must have come into contact with the key fob and the trunk came down (closed). oI did not have time to exit the trunk and ½ of my body became trapped in the trunk. oI had just enough space to move my right hand to take the key out of my pocket. oI pressed the trunk button, but the liftgate did not fully retract. It went up slightly and came back down hitting/touching my body. oI did not have enough room to get out of the trunk. oI was in a garage where no one could hear me scream for help. oI had to push up with my left hand and use excessive force with my back and right shoulder to lift the heavy trunk. Mercedes inspected the car and said nothing is wrong. Letter provided. oSeveral Mercedes employees at the dealership were present when I demonstrated the issue. They had no explanation. oSales manager stated that he tested the trunk (cars located at the dealership) and they do retract but understood my concerns as it only retracts slightly. oNo one seems to understand that serious risk this possesses, unless they were to be trapped i
- Structure
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while opening the liftgate, the rear spoiler above the liftgate became loosened while raising and scratched the roof of the vehicle. The contact stated that the rear spoiler had not detached. The vehicle was taken to the dealer, and…
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while opening the liftgate, the rear spoiler above the liftgate became loosened while raising and scratched the roof of the vehicle. The contact stated that the rear spoiler had not detached. The vehicle was taken to the dealer, and the contact was informed that the failure was caused by external factors, unrelated to NHTSA Campaign Number: 20V480000 (Structure), which had previously been performed. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 40,000.
- Engine
The engine made a knocking sound and i pulled over on the side of the road took the car to MB dealership to get the recall fixed but i was told the recall cannot be fixed until the engine is fixed. MBUSA refuses to replace the engine even though it is fully covered under warranty. Thus because i…
The engine made a knocking sound and i pulled over on the side of the road took the car to MB dealership to get the recall fixed but i was told the recall cannot be fixed until the engine is fixed. MBUSA refuses to replace the engine even though it is fully covered under warranty. Thus because i cannot get a recall done for my safety unless i get an engine replaced. This is absolutely horrible. MB knows they produced a bad engine and are forcing us to pay out of our pocket then they will fix the recall on the car.
- Engine
Engine failure. Engine has no compression which is causing injection fueler to fail. The head engine has gone bad at 50,000 miles. Head engine must be replaced and is on back order per Mercerdes Benz. After research on the issue I’ve noticed the Year/Make/Model this is issue is common at the…
Engine failure. Engine has no compression which is causing injection fueler to fail. The head engine has gone bad at 50,000 miles. Head engine must be replaced and is on back order per Mercerdes Benz. After research on the issue I’ve noticed the Year/Make/Model this is issue is common at the 40k-50k mile mark. This is a manufactured issue that Mercerdes needs to fix if so common within the car and also unsafe. Not okay for a new car to have engine failure this early
- Fuel system, gasoline
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated that there was an abnormal fuel odor inside the cabin of the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer on three occasions however, the dealer was unable to determine the cause of the…
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated that there was an abnormal fuel odor inside the cabin of the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer on three occasions however, the dealer was unable to determine the cause of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that there were no recalls on the VIN. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was approximately 45,000.
- Service brakes · Unknown or other
Since the beginning of the vehicle purchase, we heard fine metal rattling sound on the front driver side tire. Had it checked with the dealer and they recommended no repair. Now driven about 35K miles and started very loud metal scratching sound when wheels turned to right. Inspection showed…
Since the beginning of the vehicle purchase, we heard fine metal rattling sound on the front driver side tire. Had it checked with the dealer and they recommended no repair. Now driven about 35K miles and started very loud metal scratching sound when wheels turned to right. Inspection showed bent brake cover that was wearing tire uneven. Dealer claims that we went over a large bump that bent the brake cover but no such thing happened and this location is where we have been hearing this fine rattling since buying new. Raising a possibility that the manufacturing and securing process of parts around this area was not done fully and eventually cause inappropriate contact induced brake covering damage and tire wear.
- Electrical system
My GLB250 does not fall under recall 2020070009 however after taking it through the car wash the entire display instrument went out and car will not turn on and off. They are telling me the car had water damage and it is on me to fix?
- Structure
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while opening the trunk of the vehicle, the rear spoiler detached from the vehicle. The vehicle was taken to the dealer, where it was diagnosed that the rear spoiler needed to be replaced. The vehicle was not repaired. The contact…
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while opening the trunk of the vehicle, the rear spoiler detached from the vehicle. The vehicle was taken to the dealer, where it was diagnosed that the rear spoiler needed to be replaced. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 20V480000 (Structure) however, the VIN was not included. The manufacturer was notified of the failure and a case was filed. The failure mileage was approximately 35,000.
- Electrical system · Lane departure › Blind spot detection · Vehicle speed control
There's a recall on the display monitor the screen will go black sometimes come back on sometimes never come back on there was a update to fix the issue if the update doesn't work they will have to change the display module or computer that controls it when I brought it to the dealer they want to charge me to replace the display or computer , I called the manufacturer and they refused to fix the recall problem
- Unknown or other
Gap between frame and windshield causing unbearable squealing noise when driving above 75 mph. Unable to hear exterior surroundings and the squealing is causing aggravation to the ear drums of all passengers. Video provided to Mercedes dealer technician and issue has been inspected and confirmed…
Gap between frame and windshield causing unbearable squealing noise when driving above 75 mph. Unable to hear exterior surroundings and the squealing is causing aggravation to the ear drums of all passengers. Video provided to Mercedes dealer technician and issue has been inspected and confirmed by dealer. I am the 2nd owner of the vehicle and it was purchased around October/November 2022. The issue was noticed during a road trip from Jacksonville to Orlando, FL in December of 2022. There are no warning lamps or messages. However, there appeared to be a minor leak when the heat was turned on but that was not addressed when viewed by the technician. Currently, a timeframe has not been provided by Mercedes when a new windshield will be available from Germany. So at this time, I am still driving the vehicle enduring the noise since that is my only means of transportation.
- Electrical system · Unknown or other
My car has a recall from May 2021, I purchased my car Oct 2022. When asked about the recall the finance manger at Mercedes Benz of South San Francisco, Rapheal Chin stated it was no open recalls on the car. When I pointed out the repair order didn’t match the car fax, it was explained by the…
My car has a recall from May 2021, I purchased my car Oct 2022. When asked about the recall the finance manger at Mercedes Benz of South San Francisco, Rapheal Chin stated it was no open recalls on the car. When I pointed out the repair order didn’t match the car fax, it was explained by the salesman that it was completed. But NHTSA says that it was not fixed. When trying to get it fixed my car sat at the dealership for 8 days with no understanding of how to fix my car. This is clear neglect on the manufacturer and is causing me grief! My car says no updates needed, my Mercedes Benz Me App, says no updates needed but yet this recall is still open over a year later. I’ve called customer care 12 times in one day with no help. It seems as though no one throughout the Mercedes Benz company can assist me.
- Unknown or other
I had this safety recall done already why is it not removed it was done at the dealer
- Fuel system, gasoline
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while driving at approximately 30 MPH the vehicle had started shaking as if the engine was going to stall. The contact stated the check engine light was illuminated. The contact pulled over and stopped the vehicle, when she restarted…
The contact owns a 2020 Mercedes-Benz GLB250. The contact stated while driving at approximately 30 MPH the vehicle had started shaking as if the engine was going to stall. The contact stated the check engine light was illuminated. The contact pulled over and stopped the vehicle, when she restarted the vehicle it had stopped shaking. The contact stated that the vehicle failure had been intermittent but had become a recurring failure and the vehicle had stalled several times. The contact had taken the vehicle to a local dealer, where it was diagnosed and determined that the fuel injectors and a gas cap needed to be replaced. The vehicle had not been repaired. The manufacturer had been informed of the failure. The contact had researched online and related failure NHTSA Campaign Number: 21V961000 (Fuel System, Gasoline). The failure mileage was approximately 54,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008878Complaint Customer complains of wind noises. Cause The cause is being clarified. Remedy If wind noises can be clearly attributed to the roof railing, create a TIPS case with the following information: Detailed pictures of the roof railing in the actual state Detailed pictures of the roof railing in the taped-up state List of the work to pinpoint the cause Result of test to see whether the component part moves -> establish there is no rattle
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003208Complaint Noise can be heard coming from the air conditioning system at higher blower motor speeds. Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Instructions for the installation of Retrofit Kit TOP598-MFA2 Bermuda foam for model series X243/X247 A2478351400 Sealing frame A2478351500 Sealing frame A2478351600 Sealing frame A2478351700 Sealing frame A2478351800 Sealing frame A2478351900 Sealing frame A2478300104 Housing cover A2478320200 Drainage fitting Steps: 1- Remove windshield wiper as per work instructions: AR82.30-P-6100MFA 2- Remove water baffle cover as per work instructions:AR83.10-P-1411MFB 3- Thoroughly clean body/body-in-white at marked positions and remove plastic cover to air inlet. Then extract air filter. 4- Attach body-in-white foam A2478351600 to cutout at body-in-white. If necessary, fix part in place with light pressure. 5- Attach foam mat A2478351400 to previously cleaned part of body-in-white. Ensure that hole of foam mat is over the hole in the body-in-white. 6- Attach sealing frame A2478351800 along edge as shown in picture. Ensure that the plastic strip is inserted flush with the offset in the previously attached foam mat. 7- Attach sealing frame A2478351700 as shown in the picture. Take care here as the strip should be attached flush to the foam strip positioned lengthwise and must run vertically on the body-in-white downward in the direction of the seam. 8- Attach sealing frame A2478351900 as shown in the picture. Ensure that the foam strip must run along the seam and must be curved outward along the running direction at the end. (As a guide, the curvature should run so that there is a space of approx. 1 cm between the foam strip and the threaded hole). Alternatively, if the corresponding foam in the right picture is present, place the sealing frame A2478351900 along the foam as shown in the picture. 9- Insert drainage fitting A2478320200. When doing so, ensure that the foam flap is aligned in the direction of the fender as shown in the picture and does not fold upward during insertion. Insert fitting with light pressure until it audibly engages. 10- Attach sealing frame A2478351500 to water baffle as in the picture and insert inlet sieve A2478300104 (see picture). 11- Insert water baffle. When doing so, ensure that sealing frame A2478351600 does not fall out of position. Also ensure that the foam frames A2478351700, A2478351800 and A2478351900 run between the body-in-white and the water baffle (see picture). 12 - Clean out the water drains of any debris and ensure proper water flow away from the blower area. 13- Reinstallation of water baffle and windshield wiper (see step 1).
- 11000596Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.
- 10253715Check engine light active and FC P146364 Temp. and pressure sensor B4/7 is stored in Engine control unit and Fuel pump control unit. Software parameter in Fuel pump control unit. Perform software update for Fuel System Control Module (FSCM) N118. New software is A0009026661.
- 10253708In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10253706IMPORTANT EMISSION EXTENDED WARRANTY INFORMATION In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the Fuel System Control Module (FSCM) software in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the FSCM software for the fuel pressure sensor and fuel temperature plausibility check may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ("MIL") might illuminate. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P146264 The sensor Low fuel pressure and fuel temperature has a malfunction. There is an implausible signal. -and/or- P146364 This error code can be ignored and erased. 'OR' Sensor Low fuel pressure and fuel temperature has a malfunction during calculation of the fuel pressure. There is an implausible signal. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 47045 90 Control Unit, Fuel Pump - Software Parts (Software): A0009026661 Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty. No part replacement is covered by this extended warranty.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10251118After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
- 10249731Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2021 GLA and GLB (247 platform) vehicles, the identification plate on the B-pillar does not correspond to current specifications.MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the identification plate on the B-pillar.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249537Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
Every Mercedes-Benz Glb 250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.