2021 Mercedes-Benz Glb 250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › Glb 250 › 2021
These records cover every 2021 Mercedes-Benz Glb 250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
11 recalls name the 2021 Mercedes-Benz Glb 250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 CLA, 2019-2022 A-Class, 2022-2023 C-Class, 2024 CLE, 2020-2026 GLA/GLB, and 2023-2024 GLC vehicles. Please refer to MBUSA's recall report for specific model information. The micro-switch in the driver's door lock may corrode and fail to detect an open door, preventing the electronic parking brake…
Risk and remedy
Risk
A vehicle rollaway increases the risk of a crash or injury.
Remedy
Dealers will replace the driver's door lock, free of charge. Owner notification letters are expected to be mailed September 18, 2026. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Owners may contact MBUSA customer service at 1-800-367-6372. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning July 31, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLB250 vehicles. The Electronic Stability Program (ESP) unit may be damaged, which can result in disabled anti-lock brakes (ABS), disabled electronic stability control (ESC), and an electrical short circuit.
Risk and remedy
Risk
Disabled anti-lock brakes and electronic stability control can increase the risk of a crash or injury. An electrical short circuit increases the risk of a fire.
Remedy
Dealers will replace the ESP unit, free of charge. Owner notification letters were mailed October 28, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLB 250 vehicles. The level sensor linkage on the rear axle might not have been installed properly, which could affect the headlight leveling function. MBUSA's number for this recall is 2022050011.
Risk and remedy
Risk
Improperly leveled headlights may project a glare, which can impact other drivers and increase the risk of a crash.
Remedy
Dealers will inspect and repair the level sensor linkage, as necessary, free of charge. Owner notification letters were mailed June 10, 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 GLB 250 vehicles. These vehicles may be equipped with an incorrect front driver's air bag module.
Risk and remedy
Risk
An incorrect air bag module may not properly restrain an occupant during a crash. In addition, the air bag module could detach from the steering wheel during deployment. Either of these scenarios can increase the risk of injury in the event of a crash.
Remedy
Dealers will inspect and replace the front driver's air bag, as necessary, free of charge. Owner notification letters were mailed March 25, 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLB 250 and AMG GLB 35 vehicles. The driver-side window air bag may not have been mounted correctly to the lower area of the A-pillar. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 226, "Ejection Mitigation."
Risk and remedy
Risk
The driver-side window air bag may not function properly during a crash, increasing the risk of injury.
Remedy
Dealers will inspect the mounting of the driver-side window air bag and repair it as necessary, free of charge. Owner notification letters were mailed December 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 GLB35 AMG, and 2020-2021 GLB250 vehicles. The side spoilers on the tailgate might not have been installed correctly, allowing them to detach.
Risk and remedy
Risk
Detached spoilers can create a road hazard, increasing the risk of a crash or injury.
Remedy
MBUSA will notify owners, and dealers will inspect and, if necessary, replace the side spoilers, free of charge. Owner letters were mailed July 2, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021050009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 GLB250 vehicles. The wheel arch covers on the front fenders might not have been installed correctly, allow them to detach.
Risk and remedy
Risk
Detached wheel arch covers can create a road hazard, increasing the risk of a crash or injury.
Remedy
MBUSA will notify owners, and dealers will check the installation of the front wheel arch covers and correct them as necessary, free of charge. Owner letters were mailed May 21, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021040015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Owner complaints
29 complaints
What owners report most
Latest complaints
- Structure › Body › Roof and pillars
The contact owns a 2021 Mercedes-Benz GLB250. The contact stated that the front stationary roof panel detached from the vehicle and shattered. The vehicle was taken to the dealer but was not diagnosed or repaired. The contact became aware of a recall with a similar failure; however, the VIN was not…
The contact owns a 2021 Mercedes-Benz GLB250. The contact stated that the front stationary roof panel detached from the vehicle and shattered. The vehicle was taken to the dealer but was not diagnosed or repaired. The contact became aware of a recall with a similar failure; however, the VIN was not included, and the model year was not included in a recall for the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 63,000.
- Unknown or other
Family and I were driving on the interstate and heard a loud bang (like a shotgun) followed by immediate glass everywhere. The panoramic sunroof exploded. We had to drive 4 hours like this - lucky we didn’t jerk the wheel on the interstate with the noise. Absolutely sickening that this is so prevalent and Mercedes won’t do anything about it.
- Engine · Unknown or other
When my car sits in the rain for long periods of time, while driving, it will automatically switch into neutral and give me a "transmission malfunction stop" & "service required do not shift gears visit dealer" sign on the dash. This has happened at least 7 times in 2 years since March 2024. The…
When my car sits in the rain for long periods of time, while driving, it will automatically switch into neutral and give me a "transmission malfunction stop" & "service required do not shift gears visit dealer" sign on the dash. This has happened at least 7 times in 2 years since March 2024. The latest time it happened was last week. I will get into my car after a day at work, when it has been raining, drive a few miles and the car will switch into neutral and display those signs. This is incredibly dangerous for my safety as the driver, any passengers and any other cars on the road. While going 55+ miles an hour, my car, without any warning shifts into neutral. I have taken it to my local dealership for inspection every time that it happens and they have repeatedly told me they cannot find a fix for it and do not know why it is happening besides a electrical problem due to water. They advised me to file a claim with corporate Mercedes but that was denied. I have photos and documentation from the dealership of when I have brought it in for inspection and they have confirmed the issue. They will not help with a solution for this problem. They have told me to pull over, turn the car on and back off to get it to go away but it continues to do the same repeated problem.
- Steering · Suspension · Unknown or other
The component that appears to have malfunctioned is the front axle integral carrier (front subframe) and the related front suspension geometry, as the vehicle now exhibits a persistent pull to the left and degraded steering stability after the dealer replaced the front lower control arms, engine…
The component that appears to have malfunctioned is the front axle integral carrier (front subframe) and the related front suspension geometry, as the vehicle now exhibits a persistent pull to the left and degraded steering stability after the dealer replaced the front lower control arms, engine mounts, and performed alignments; this area of the vehicle is fully available for inspection upon request. My safety and the safety of others were put at risk because the vehicle requires constant steering correction to avoid drifting left, creating a danger of unintended lane departure and loss of control, which aligns with the steering‑related risks described in NHTSA Recall 21V990 / MBUSA 2022070009, where failure of the integral carrier can impair steering and increase crash risk. The problem has been reproduced by me on every drive, though the dealer stated they “did not find anything,” despite alignment printouts showing front camber imbalance and lack of caster correction. The vehicle has been inspected twice by the authorized Mercedes‑Benz dealer, but they did not inspect or address the front axle integral carrier even though the recall documentation shows that corrosion or structural issues in this part can affect steering performance and connection to other components. There were no warning lamps or dashboard alerts; the symptoms began immediately after the dealer’s suspension and mount repairs, and the steering pull and unstable handling have continued ever since.
- Power train · Service brakes · Wheels
I purchased this vehicle in May 28 2025. I certified car. I took in for oil change Nov 17-2025. Found out they had lot of issues., left front bushing arm leaking. Rt engine mount leaking. Bad brakes battery low. Bad tire rt back passage side.front wheel axle and rear wheel axle is bad and screw on the engine mount is missing. Screw and leaking..?and the vehicle needed a alignment.
- Engine · Fuel/propulsion system
Engine locked up while driving out of state on the interstate. Vehicle lost all power and engine stopped functioning. Managed to pull over and stop the vehicle on the side of the interstate. Had truck towed to repair shop where they diagnosed connecting rod/crankshaft bearing failure, as well as…
Engine locked up while driving out of state on the interstate. Vehicle lost all power and engine stopped functioning. Managed to pull over and stop the vehicle on the side of the interstate. Had truck towed to repair shop where they diagnosed connecting rod/crankshaft bearing failure, as well as lifter and cylinder misfire/failure on cylinder 7. Metal shavings were discovered in the oil, and engine locked up and cannot be repaired. I am currently in the process of having the engine replaced, but yes currently an inspection can still be performed, and I can provide statements and diagnostics from the mechanic. This failure put myself and my family in a scary situation. The engine was shaking violently before it stopped functioning and this made the truck very difficult to steer, not to mention this was during rush hour and we were in heavy traffic moving at speeds of 70mph+. Luckily we managed to get off the road, and to a safer location, but this left us stranded on the side of the road for 2 hours waiting on a tow. The vehicle was inspected by a GMC dealership initially where they only diagnosed lifter and cylinder misfire/failure. Due to the price of their quote to repair that issue, I took the vehicle to a certified mechanic, and thats when we found there was also connecting rod/crankshaft bearing failure prior to repairing the lifter/cylinder misfire. There were no prior warnings to this happening. No check engine lights, no noises, and no noticeable changes in the vehicle. Everything seemed to be operating normally.
- Power train
It appears as if there IS an issue with the transmission. In this vehicle. When you come to a stop the transmission has a loud clunking noise coming from left side of vehicle. The clunking occurs when the vehicle downshifts. It clunks from D4 to D3, then D3 to D2 , and again at D2 to D1. I have…
It appears as if there IS an issue with the transmission. In this vehicle. When you come to a stop the transmission has a loud clunking noise coming from left side of vehicle. The clunking occurs when the vehicle downshifts. It clunks from D4 to D3, then D3 to D2 , and again at D2 to D1. I have taken it to the dealer numerous times to have it checked. The service mgr weny for s test drive with me and heard it. I was then told the clunking was " normal" . I purchased the vehicle as a certified used vehicle from the same dealer . this has been occuring since purchase in may 2024
- Visibility/wiper
Driving on north bound of Merritt Parkway between exit 17 and 18. Today 12/10/25 9:28 AM My panoramic sunroof exploded ! all catch on video, driver on the vehicle behind me , came to check on me; and told me the glass went over four feet up in the air and then hit his vehicle windshield, I call…
Driving on north bound of Merritt Parkway between exit 17 and 18. Today 12/10/25 9:28 AM My panoramic sunroof exploded ! all catch on video, driver on the vehicle behind me , came to check on me; and told me the glass went over four feet up in the air and then hit his vehicle windshield, I call Mercedes Benz customer service support to report the incident and open a case, they told me to drive to the closest dealer from the incident (Mercedes Benz of Fairfield) when I arrived and show the vehicle to the technician, he was trying to tell me that was my fault and he never heard such a thing of a sunroof explosion… and was looking for a reason to blame me, I told him I got all on video due to I have a dash camera that records the our side and the inside of the vehicle.. the outside temperature was 30 degrees Fahrenheit, and the inside temperature in the vehicle was set to 69 degrees… My speed was 55 to 56 miles per hour. Light to moderate traffic, the explosion sound like a gunshot, that was my first impression, some one shoot at me… The dealer, told me that I should call my insurance or Mercedes Benz and the only think they can do, is to tell me how much will cost to repair the damage.. and that they will park my car on a different building so don’t get rain on it, until I decided what I want to do.
- Engine
Engine showed signs of loss of power and excess noise. It was taken to dealership via MB roadside assistance. At the dealership, they diagnosed it with engine catastrophic failure due to metal parts found in the oil filter. At no time was the engine disassembled to ensure known defects and still…
Engine showed signs of loss of power and excess noise. It was taken to dealership via MB roadside assistance. At the dealership, they diagnosed it with engine catastrophic failure due to metal parts found in the oil filter. At no time was the engine disassembled to ensure known defects and still under warranty parts were not the cause. Dealer estimated the repair to cost in excess of $22K. MBUSA was contacted and they made no efforts to make the situation whole. The cost estimated was for the complete engine replacement. An engine that only has 53k miles. Although all routine maintenance have been conducted, engine failure was certainly pre-mature. Issues exhibited were excessive engine vibration, loss of power and excess noise.
- Steering · Suspension · Unknown or other
Escalating Safety Concern – Loud Clunking, Thumping, and Cracking from Front Axle at Low Speeds We are long-time loyal customers and currently own four identical Mercedes-Benz models. Unfortunately, one of our vehicles, a 2021 mb glb250 has recently developed severe clunking, thumping, and loud…
Escalating Safety Concern – Loud Clunking, Thumping, and Cracking from Front Axle at Low Speeds We are long-time loyal customers and currently own four identical Mercedes-Benz models. Unfortunately, one of our vehicles, a 2021 mb glb250 has recently developed severe clunking, thumping, and loud cracking noises originating from the front axle area, noticeable especially at low speeds. The problem appeared suddenly and is rapidly worsening. After researching the issue, we’ve discovered that many owners of the exact same model and model year report identical symptoms. This appears to be a widespread and recurring problem that raises serious safety concerns, particularly as it affects the front axle and is uncommon in other modern vehicles of this class and young age. Given the potential safety implications and the growing number of affected owners, we respectfully request that Mercedes-Benz investigate this issue promptly, acknowledge it as a known concern, and provide an appropriate inspection and repair at no cost to us. We love the brand and have always trusted its engineering and safety standards, which makes this experience especially distressing. We would greatly appreciate your immediate attention and a clear response on next steps.
- Unknown or other
While driving, the panoramic moonroof on my 2021 Mercedes-Benz GLB 250 (VIN: [XXX] ) suddenly shattered without any visible impact or prior damage. It sounded like an explosion, and glass rained down into the vehicle. This could have caused serious injury to myself or my child. There was no…
While driving, the panoramic moonroof on my 2021 Mercedes-Benz GLB 250 (VIN: [XXX] ) suddenly shattered without any visible impact or prior damage. It sounded like an explosion, and glass rained down into the vehicle. This could have caused serious injury to myself or my child. There was no indication that a rock or debris hit the vehicle. No vehicles were in front of me, and I have no history of impact damage. This seems to have happened spontaneously, and after researching the issue, I found it is a common problem across various Mercedes-Benz models. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine · Fuel/propulsion system · Power train
In April 2025, my 2021 Mercedes-Benz GLB 250 (81,000 miles) suffered repeated engine issues caused by a cylinder head failure. The dealer attempted a cylinder head replacement, but during their own test drive after repairs, the engine completely seized and failed again on their property. This…
In April 2025, my 2021 Mercedes-Benz GLB 250 (81,000 miles) suffered repeated engine issues caused by a cylinder head failure. The dealer attempted a cylinder head replacement, but during their own test drive after repairs, the engine completely seized and failed again on their property. This indicates a severe defect in the engine assembly that risks sudden power loss while driving, which could cause an accident. Prior to the failure, there were warning messages about misfires and rough idle. The problem has been confirmed by an authorized Mercedes-Benz dealer and the car has been kept at their shop since April, with no resolution. I am concerned this is a recurring safety defect affecting other GLB 250 vehicles. The vehicle is available for inspection and remains undriveable due to the failed engine. I request NHTSA to investigate for possible safety-related design or manufacturing defects that could cause sudden engine seizure and loss of power while driving.
- Seat belts
Seat belt failure.Driver side…mechanism… it feels unsafe…the retractor is not locking
- Engine · Unknown or other
Jerking and loud noise from the engine after attempting to accelerate from a red light stop. Vehicle is idling very roughly and almost sounds like a diesel engine. Check engine light came on. Inspection at the dealership found multiple faults for camshaft positions deviating from the specified…
Jerking and loud noise from the engine after attempting to accelerate from a red light stop. Vehicle is idling very roughly and almost sounds like a diesel engine. Check engine light came on. Inspection at the dealership found multiple faults for camshaft positions deviating from the specified value. When the oil filter was removed, the shop reported finding some metal particles in the oil. The conclusion was that a mechanical fault caused a metal part in the engine to brake and clog up the engine. The car did not run smoothly after the jerking sound and could have caused an accident if the car was in active motion. The recommendation now is that the engine needs to be replaced.
- Tires › Tread/belt
The contact owns a 2021 Mercedes-Benz GLB250 equipped with Continental Tires, Tire Line: ProContact GX SSR, Tire Line: 235/55/R18, DOT Number: A33LWXX41220. The contact stated while driving 70 MPH, the vehicle began to vibrate with a flapping sound coming from the vehicle. Despite the failure, the…
The contact owns a 2021 Mercedes-Benz GLB250 equipped with Continental Tires, Tire Line: ProContact GX SSR, Tire Line: 235/55/R18, DOT Number: A33LWXX41220. The contact stated while driving 70 MPH, the vehicle began to vibrate with a flapping sound coming from the vehicle. Despite the failure, the contact was able to drive the vehicle to the residence. The contact then drove the vehicle to an independent mechanic where three humps were discovered on the front driver’s side tire that had formed due to thread separation on the inside of the tire. The mechanic referred the contact to a dealer who then referred the contact to the Continental tire manufacturer. The manufacturer informed the contact that the tire should be sent to the headquarters for an inspection. The tire was replaced. The failure mileage was approximately 30,600.
- Unknown or other
Glass that’s in between the windshield and sunroof
- Engine
Cylinder Head gone bad at 35,000 miles
- Unknown or other
My fuel tank cover would not open. Car was under warranty so MB was able to replace the motor of the fuel cap release. Problem, there is no manual release for the fuel cap so if you are low on fuel and need to fill up, you would be stranded. They need a manual release for the fuel cap for safety.
- Air bags · Electrical system · Structure › Body
Entire electrical system went out while driving causing check engine light to come on after the failure of system; there was no dashboard working at all when the system went out; without the dashboard out it was not certain if the vehicle was safe to drive anymore; the dealer has not been able to…
Entire electrical system went out while driving causing check engine light to come on after the failure of system; there was no dashboard working at all when the system went out; without the dashboard out it was not certain if the vehicle was safe to drive anymore; the dealer has not been able to reproduce the problem; the vehicle has been with the dealer repair system for several weeks and have not been able to determine what happened; they have indicated that the vehicle had some type of water intrusion which short circuited the electrical system; the believes that the water entered into from the windshield area with a possible clogged water drain; there was no prior warning
- Visibility
The contact owns a 2021 Mercedes-Benz GLB250. The contact stated that the vehicle was parked in the garage; however, after driving out of the garage, the contact became aware of a crack on the windshield from the rear-view mirror ten inches downward. The contact stated that the crack seemed to be…
The contact owns a 2021 Mercedes-Benz GLB250. The contact stated that the vehicle was parked in the garage; however, after driving out of the garage, the contact became aware of a crack on the windshield from the rear-view mirror ten inches downward. The contact stated that the crack seemed to be on the inside over the sensors. The vehicle had not yet been diagnosed or repaired. The dealer nor manufacturer was notified of the failure. The failure mileage was 13,716.
- Electrical system
The horn randomly starts honking while driving posing a serious safety risk. it makes driving the vehicle seem like it is stolen.
- Unknown or other
The car has 29,000 miles and I took it on a two day trip across part of the country. It was driven hard but had a oil change before leaving. After arriving home it started to sputter and have no "energy". I had the cabin filter and engine filter changed and another oil change just in case. took…
The car has 29,000 miles and I took it on a two day trip across part of the country. It was driven hard but had a oil change before leaving. After arriving home it started to sputter and have no "energy". I had the cabin filter and engine filter changed and another oil change just in case. took it to deal as it continued to sputter, even worse, jerk forward. It blew a cylinder head. Checking the internet I find that this is a usual problem with this year and model car. Why isn't it in the recall if a lot of this model has this problem?
- Back over prevention · Electrical system
The contact owns a 2021 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time…
The contact owns a 2021 Mercedes-Benz GLB250. The contact received notification of NHTSA Campaign Number: 21V354000 (Back Over Prevention, Electrical System) however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that several unknown local dealers were contacted, and the contact was referred to the manufacturer for further assistance. The manufacturer was contacted, and a case was opened. The contact had not experienced a failure. Parts distribution disconnect. The contact stated that the manufacturer was able to complete the repairs necessary to fix the issue and no longer wishes to keep this complaint.
- Suspension
Front right ball joint separated from lower control arm with no advance warning and the drive shaft was disconnected from the vehicle body. I was travelling at about 15 mph in a straight line through an intersection on a flat surface with no potholes. Then I saw a warning of a transmission fault…
Front right ball joint separated from lower control arm with no advance warning and the drive shaft was disconnected from the vehicle body. I was travelling at about 15 mph in a straight line through an intersection on a flat surface with no potholes. Then I saw a warning of a transmission fault in my instrument cluster, followed by a loud grinding sound. My car then came to a stop and I was unable to move the vehicle in Forward or Reverse gear. I ignition cycled the vehicle and tried forward/reverse, then someone told me that my front right wheel had separated. Upon inspecting my car from the outside, I then saw the mechanical failure that had occurred. The ball joint separated from the lower control arm . The drive shaft from the front right wheel also separated from the vehicle body. I also noticed that a ring-connector for the drive shaft had been flung maybe 4 feet from my car. My car was in a non-driveable condition and I could not engage drive with the transmission, my car had to be towed from the scene. If this had happened on a busier street or at higher speeds this would have been a severe collision. My car was just delivered to a Mercedes Dealership after sitting in a tow yard for several days, they have not yet fully inspected the vehicle. My insurance has not yet sent a representative to see the vehicle. The indication I had was a "TRANSMISSION FAULT" displayed on my instrument cluster, but I did not notice any other telltales on the instrument cluster after coming to a stop. To the best of my knowledge I did not collide with any objects before the event. There is damage to the outside of my front right rim and tire in the photos, I believe this damage occurred as part of the mechanical failure and how the tire may have deformed and the rim contacted the ground.
- Unknown or other
On September 3, 2022 while traveling east on AL highway 110 the sunroof exploded as i was driving. Notified Montgomery county sheriff Department but they refuse to do a report because it wasn’t an accident. The dealership said something had to hit the sunroof for it to Shadder. Explained to the…
On September 3, 2022 while traveling east on AL highway 110 the sunroof exploded as i was driving. Notified Montgomery county sheriff Department but they refuse to do a report because it wasn’t an accident. The dealership said something had to hit the sunroof for it to Shadder. Explained to the service advisor that there were no other vehicles in the area when the incident happened, so what could have hit it. Was informed by the service advisor that the car didn’t have a recall for the sunroof on this particular model.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008878Complaint Customer complains of wind noises. Cause The cause is being clarified. Remedy If wind noises can be clearly attributed to the roof railing, create a TIPS case with the following information: Detailed pictures of the roof railing in the actual state Detailed pictures of the roof railing in the taped-up state List of the work to pinpoint the cause Result of test to see whether the component part moves -> establish there is no rattle
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005288Complaint Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, 247476 247747, 247646 247647 the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, 247751 247753, 274651 the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part.
- 11003208Complaint Noise can be heard coming from the air conditioning system at higher blower motor speeds. Cause Leaves/foreign objects have entered through the water drain grille in the water drain thereby causing an imbalance and noise in the blower wheel. Remedy Instructions for the installation of Retrofit Kit TOP598-MFA2 Bermuda foam for model series X243/X247 A2478351400 Sealing frame A2478351500 Sealing frame A2478351600 Sealing frame A2478351700 Sealing frame A2478351800 Sealing frame A2478351900 Sealing frame A2478300104 Housing cover A2478320200 Drainage fitting Steps: 1- Remove windshield wiper as per work instructions: AR82.30-P-6100MFA 2- Remove water baffle cover as per work instructions:AR83.10-P-1411MFB 3- Thoroughly clean body/body-in-white at marked positions and remove plastic cover to air inlet. Then extract air filter. 4- Attach body-in-white foam A2478351600 to cutout at body-in-white. If necessary, fix part in place with light pressure. 5- Attach foam mat A2478351400 to previously cleaned part of body-in-white. Ensure that hole of foam mat is over the hole in the body-in-white. 6- Attach sealing frame A2478351800 along edge as shown in picture. Ensure that the plastic strip is inserted flush with the offset in the previously attached foam mat. 7- Attach sealing frame A2478351700 as shown in the picture. Take care here as the strip should be attached flush to the foam strip positioned lengthwise and must run vertically on the body-in-white downward in the direction of the seam. 8- Attach sealing frame A2478351900 as shown in the picture. Ensure that the foam strip must run along the seam and must be curved outward along the running direction at the end. (As a guide, the curvature should run so that there is a space of approx. 1 cm between the foam strip and the threaded hole). Alternatively, if the corresponding foam in the right picture is present, place the sealing frame A2478351900 along the foam as shown in the picture. 9- Insert drainage fitting A2478320200. When doing so, ensure that the foam flap is aligned in the direction of the fender as shown in the picture and does not fold upward during insertion. Insert fitting with light pressure until it audibly engages. 10- Attach sealing frame A2478351500 to water baffle as in the picture and insert inlet sieve A2478300104 (see picture). 11- Insert water baffle. When doing so, ensure that sealing frame A2478351600 does not fall out of position. Also ensure that the foam frames A2478351700, A2478351800 and A2478351900 run between the body-in-white and the water baffle (see picture). 12 - Clean out the water drains of any debris and ensure proper water flow away from the blower area. 13- Reinstallation of water baffle and windshield wiper (see step 1).
- 11000596Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.
- 11000541Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-24 C-Class, CLA, EQB, EQE, EQS, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (118, 167, 192, 206, 223, 232, 243, 247, 254, 290, 294, 295, 296 and 297 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for a better entertainment experience. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10253715Check engine light active and FC P146364 Temp. and pressure sensor B4/7 is stored in Engine control unit and Fuel pump control unit. Software parameter in Fuel pump control unit. Perform software update for Fuel System Control Module (FSCM) N118. New software is A0009026661.
- 10253708In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10253706IMPORTANT EMISSION EXTENDED WARRANTY INFORMATION In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the Fuel System Control Module (FSCM) software in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the FSCM software for the fuel pressure sensor and fuel temperature plausibility check may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ("MIL") might illuminate. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P146264 The sensor Low fuel pressure and fuel temperature has a malfunction. There is an implausible signal. -and/or- P146364 This error code can be ignored and erased. 'OR' Sensor Low fuel pressure and fuel temperature has a malfunction during calculation of the fuel pressure. There is an implausible signal. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 47045 90 Control Unit, Fuel Pump - Software Parts (Software): A0009026661 Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty. No part replacement is covered by this extended warranty.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251176Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
- 10251118After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 10249740Dear Mercedes-Benz Owner: On behalf of Mercedes-Benz USA, LLC (MBUSA), thank you for being a part of the Mercedes-Benz family. We hope that youre enjoying your vehicle. Here at MBUSA, we are committed to delivering an exceptional ownership experience. In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you about an Over-the-Air (OTA) Service Campaign to update the Communication Module software on certain Model Year 2020-2023 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, and S-Class vehicles. This update will improve the system stability and allow for better accessibility of Mercedes me services. This OTA update will be provided free of charge and will be performed in the background. No action is needed on your behalf. Your vehicle does not appear to have an active Mercedes me connect subscription. In this case, the OTA update will be performed unless you choose to opt-out from receiving this OTA update. What will your Dealer do? NO DEALER ACTION IS NECESSARY for this OTA update. You do not need to visit a Mercedes-Benz dealer. Opting-out of this OTA Update: Customers who are not subscribed to the Mercedes me connect service may opt-out of this OTA update by emailing or by calling 1-800-FOR-MERCEDES. The opt-out period will start on January 5, 2024 and end on February 4, 2024. If you choose to opt-out, the described update will not be available for your vehicle as an additional workshop measure. No action is necessary for Opting-In. Once the opt-out period has closed on February 4, 2024, this OTA will be automatically downloaded and installed. Thank you for allowing us to continue taking care of your vehicle.
- 10249731Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2020-2021 GLA and GLB (247 platform) vehicles, the identification plate on the B-pillar does not correspond to current specifications.MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will replace the identification plate on the B-pillar.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249537Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
Every Mercedes-Benz Glb 250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.