2016 Mercedes-Benz GLE450
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLE450 › 2016
These records cover every 2016 Mercedes-Benz GLE450. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
11 recalls name the 2016 Mercedes-Benz GLE450. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML550, 2012-2015 ML350, AMG ML63, 2015 ML250, ML400, 2016 GLE450, GLE300, 2016-2018 GLE350, GLE550, 2016-2019 GLE400, 2017-2019 AMG GLE43, and 2016-2020 AMG GLE63 vehicles. Water might accumulate in the spare tire wheel well and damage the fuel pump control unit, which could cause an engine…
Risk and remedy
Risk
An engine stall while driving increases the risk of a crash.
Remedy
Dealers will install a water drain plug, inspect for water intrusion, and replace the fuel pump control unit as necessary, free of charge. Owner notification letters were mailed February 15, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2023010002 and 2023010003.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012-2014 ML350 Bluetec 4Matic and ML550 4Matic, 2012-2015 ML63 AMG 4Matic and ML350 4Matic, 2013-2016 GL350 Bluetec 4Matic, GL550 4Matic and GL63 AMG 4Matic, 2017 GLS350d 4Matic, GLS450 4Matic, GLS550 4Matic and GLS63 AMG 4Matic, 2015 ML400 4Matic, 2016 GLE400 4Matic, GLE350 4Matic, GLE63 AMG 4Matic…
Risk and remedy
Risk
The leaking oil in the presence of an ignition source can increase the risk of a fire.
Remedy
MBUSA will notify owners, and dealers will correct the oil level as necessary and replace the reservoir sealing cap to prevent oil foam from leaking out, free of charge. The recall began August 30, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018070015.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 GLE350 4Matic, GLE350, GLE350 4Matic Bluetec, GL450 4Matic, and GLE450 Coupe 4Matic vehicles. In the affected vehicles, the bolt that connects the upper control arm and the axle stub may not have been properly tightened.
Risk and remedy
Risk
The loose bolt may cause improper wheel tracking, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the tightness of the bolt connecting the upper control arm and the axle stub on the affected vehicles, replacing the upper control arm if necessary, free of charge. The recall began March 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016-2017 GL350 4Matic Bluetec, GL550 4Matic, GLE350 4Matic, GLE43 AMG Coupe, GLE450 4Matic, 2016 GLE300d 4Matic, GLE350, GLE350d 4Matic, GLE400 4Matic, GLE550e 4Matic, GLE63 AMG, GLE63 AMG 4Matic, GLE63S AMG 4Matic Coupe, and 2017 GLS63 AMG vehicles manufactured April 23, 2014, to May 10, 2016.…
Risk and remedy
Risk
If the front passenger air bag does not deploy as necessary in the event of a crash, the front passenger has an increased risk of injury.
Remedy
MBUSA will notify owners, and dealers will update the OCS software, free of charge. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 GLE Coupe 450 AMG 4Matic vehicles manufactured July 11, 2015, to July 25, 2015. The affected vehicles may be equipped with rear head restraints that may not stay locked in the upright position at very low temperatures.
Risk and remedy
Risk
If the vehicle is involved in a crash in very low temperatures, the rear head restraints may not function as intended, increasing the risk of rearseat occupant injury.
Remedy
MBUSA will notify owners, and dealers will replace the rear head restraints, free of charge. The recall is expected to begin in October 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2015 ML250, ML350, ML350 4Matic, ML400 4Matic, ML63 AMG, and 2016 GLE450 AMG 4Matic vehicles manufactured from April 27, 2015, through May 19, 2015. The affected vehicles may have had the right rear seatbelt anchor bolt incorrectly installed.
Risk and remedy
Risk
In the event of a vehicle crash, the right rear seatbelt anchor bolt could fail to secure the passenger, increasing their risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect and, if necessary, correct the installation of the right rear seat belt anchor bolt, free of charge. The recall began on July 22, 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2016 GLE450 AMG 4Matic Coupe vehicles manufactured December 10, 2014, to June 6, 2016. An error within the engine control unit (ECU) software may allow the engine to shut-down while the vehicle is braking, possibly confusing the driver into thinking the shut-down was planned due to the ECO…
Risk and remedy
Risk
If the engine shuts down unintentionally, there may be an increased risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the ECU software, free of charge. The recall began August 2016. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2016 GLE450 AMG 4Matic coupes and GLE63 AMG S 4Matic coupes manufactured December 10, 2014, to April 29, 2015. The affected vehicles may be equipped with rear drive shaft bolt fasteners that may loosen and result in the rear drive shaft separating from the transmission or the rear axle…
Risk and remedy
Risk
If the drive shaft separates, the vehicle will stall, increasing the risk of a vehicle crash.
Remedy
MBUSA will notify owners, and dealers will inspect the bolt fasteners, tightening them as necessary, free of charge. The recall is expected to begin in mid-November 2015. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
25 complaints4 involved a crash2 injuries
What owners report most
Latest complaints
- Power train · Service brakes
Mercedes-benz corporate IS showing a complete disregard for me as a consumer and human! My brakes recently failed without warning (i lost my ability to brake) and it almost caused me to be involved in an accident. My life and safety was put in jeopardy and I am in shock. At their request I had my…
Mercedes-benz corporate IS showing a complete disregard for me as a consumer and human! My brakes recently failed without warning (i lost my ability to brake) and it almost caused me to be involved in an accident. My life and safety was put in jeopardy and I am in shock. At their request I had my vehicle towed in to mercedes-benz service and corporate escalation IS denying my claim and not providing me assistance in any way.
- Electrical system · Forward collision avoidance › Adaptive cruise control · Vehicle speed control
I was reversing the vehicle and it stopped and shfted into drive at a high speed unitl it stopped after hitting fence and tilted on its side
- Structure › Body › Roof and pillars
The contact owns a 2016 Mercedes-Benz GLE450. The contact stated while driving at an undisclosed speed, the front roof panel detached and flew off the vehicle. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact referenced an unknown recall; however, the…
The contact owns a 2016 Mercedes-Benz GLE450. The contact stated while driving at an undisclosed speed, the front roof panel detached and flew off the vehicle. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact referenced an unknown recall; however, the VIN was not included in the recall. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 104,620.
- Back over prevention › Sensing system › Camera
Mercedes Benz 2016 GLE450 AMG Coupe Backup Camera issue. The software problems cause backup camera to go blank /black screen. It does this randomly, it can worked for few weeks to a month, then suddenly just goes blank/black when the gear is in reverse (R). I have made complained to Mercedes Benz…
Mercedes Benz 2016 GLE450 AMG Coupe Backup Camera issue. The software problems cause backup camera to go blank /black screen. It does this randomly, it can worked for few weeks to a month, then suddenly just goes blank/black when the gear is in reverse (R). I have made complained to Mercedes Benz dealer when the issue first started and I was told that the year of my vehicle is not listed in the recall that was issued for the Mercedes Benz with backup camera issues, the recall was listed for 2019-2021. I was told that I have to wait until there is a recall for the 2016 GLE450 AMG Coupe.
- Engine
Gear Shift issue there are several forums with this issue car goes from park to neutral when trying to shift to drive. then goes straight to drive 3 stuck between drive 3 and drive 5 the very concerning issue is if the car does shift to drive 1 it throws itself into neutral while driving this is an…
Gear Shift issue there are several forums with this issue car goes from park to neutral when trying to shift to drive. then goes straight to drive 3 stuck between drive 3 and drive 5 the very concerning issue is if the car does shift to drive 1 it throws itself into neutral while driving this is an extremely dangerous issue ! mercedes has to know because of the complaints extremely upset that no recall has been issued ...
- Engine
There is a known issue With this vehicle with the shifting(hard shifting) there's a glitch when shifting to drive it automatically shifts to neutral then to drive 3 ! the glitch is that its not transmitting correctly to the transmission . if the car does shift to drive 1 it throws itself into…
There is a known issue With this vehicle with the shifting(hard shifting) there's a glitch when shifting to drive it automatically shifts to neutral then to drive 3 ! the glitch is that its not transmitting correctly to the transmission . if the car does shift to drive 1 it throws itself into neutral while driving that's dangerous !! there are several forums with this issue and I am very surprised there has been no recall this is very upsetting!
- Back over prevention › Warnings · Electrical system · Forward collision avoidance › Warnings
While parking and putting my car in park. Hello, my car needs a recall. August 31, 2024 While parking and putting the car in park. my car shifted into Neutral and lunged forward causing me to hit a sign and maneuver away from a wall. My car is dangerous. Please help!! My car lunged forward and i ran into a bush. I am injured. This car malfunction jumping gears. Not shifting properly the car is dangerous.
- Fuel/propulsion system · Structure › Body
In May 2023 I took my 2016 GLE 450 AMG into "Park Place Motor Cars Mercedes" (Dallas) for the (MBUSA 2023010002 and 2023010003) "Water that could Leak into the Spare Tire area, Impacting the Fuel Pump" recall. Park Place stated that they didn't locate any signs of water in the trunk area and would…
In May 2023 I took my 2016 GLE 450 AMG into "Park Place Motor Cars Mercedes" (Dallas) for the (MBUSA 2023010002 and 2023010003) "Water that could Leak into the Spare Tire area, Impacting the Fuel Pump" recall. Park Place stated that they didn't locate any signs of water in the trunk area and would place a water drain plug in the spare tire area to drain water, incase water entered the area. In January 26, 2024, while driving, my GLE 450 loss propulsion without warning causing me to almost get rear ended. Unbeknownst to me, that this was related to the recall from 2023, I had the vehicle towed to a local "certified repair shop". The shop stated that i would need to replace the fuel pump units. Approximately 2 months later while my daughter was driving the GLE 450, the vehicle loss propulsion without warning once again causing my daughter to be stranded at a "Stop sign" 30 miles from home at approximately 1245 am. I had the vehicle towed to "Park Place Motorcars". Service advisor informed me that the Fuel pump unit had failed due to water entering into the trunk and they would have to determine where the water was coming from. I then asked to speak to manager and I remembered that a recall describing this situation had been conducted less than a year prior to this incident (2x). After approximately 1 month the service advisor messaged me and stated that the repair(s) wouldn't be covered under the recall warranty due to the fact that debris was found underneath the vehicle, causing the drain plug to be blocked. I am terrified to allow my family to continue driving this vehicle with the current remedy that Mercedes has chosen to use (drain plug), that did NOT fix the problem specified in the defective issue within the recall paperwork. The REMEDY should be to determine how the water is entering into the vehicle. The water has caused 2 fuel pump incidents within 1 year leading to the loss of propulsion without warning and increasing the risk of a serious crash.
- Steering
The contact owns a 2016 Mercedes-Benz GLE. The contact stated that while driving at approximately 20 MPH, the steering wheel stopped operating and the vehicle crashed into a guard rail. The warning message "power steering" failure was displayed after the crash. No air bags were deployed and no…
The contact owns a 2016 Mercedes-Benz GLE. The contact stated that while driving at approximately 20 MPH, the steering wheel stopped operating and the vehicle crashed into a guard rail. The warning message "power steering" failure was displayed after the crash. No air bags were deployed and no injuries were sustained. The vehicle was taken to a repair shop where it was diagnosed with a failed electric power steering and control module. The vehicle was not repaired. The vehicle was taken to the dealer where the power steering failure was confirmed. The vehicle was not repaired. The contact discovered the NHTSA Campaign Number: 17V241000 (Steering), however, the contact was not notified of the campaign. The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 110,000.
- Fuel/propulsion system · Suspension
Front upper control arm sway bushings cracking after being replaced. Strained vehicle Noise when going over numbs or dips. Unstable suspension. Also output shaft is leaking oil.
- Electrical system · Fuel/propulsion system · Structure › Body
My 2016 Mercedes GLE 450 AMG was running perfectly but stalled while I was making a left turn onto a major roadway and I was inches from a catastrophic accident. My car was towed to Mercedes Benz dealership and the technician informed me that the trunk seal was not sealing properly causing water to…
My 2016 Mercedes GLE 450 AMG was running perfectly but stalled while I was making a left turn onto a major roadway and I was inches from a catastrophic accident. My car was towed to Mercedes Benz dealership and the technician informed me that the trunk seal was not sealing properly causing water to get in through the trunk and shorted out a fuel pump module. My trunk was not wet and only indication of water was when the rear compartment was lifted near the spare tire area so I was not aware of a possible leak. My car is mostly garage kept unless I am at work where it’s exposed to weather. It had been raining for several days in our area. After doing online research, it appears to be an existing problem for Mercedes owners. I’m concerned because I could have lost my life due to this issue and someone may not be so fortunate if the problem goes unresolved.
- Electrical system · Engine · Power train
Electrical - Drivers lock does not lock/unlock with remote, with door lock. Have to physically lock/unlock drivers door. if you do not you will not get in door and you will not open from inside. If you do not lock manually your door will be open even though the other doors locked. Power Train -…
Electrical - Drivers lock does not lock/unlock with remote, with door lock. Have to physically lock/unlock drivers door. if you do not you will not get in door and you will not open from inside. If you do not lock manually your door will be open even though the other doors locked. Power Train - transmission is clucking between gear especially at slow speeds, Transmission in L1-5 sometimes does not shift up or down. sometimes does not go into drive from manually shifting from L gears. some downhills the tranny does not slow vehicle on down hills. Engine - valves and lifters are noisy at startup. Sounds like 1 or two cylinders. Suspension - Rear stock suspension bottoms easily also excessive motion up and down.
- Steering
The contact owns a 2016 Mercedes-Benz GLE450. The contact stated that while driving approximately 40 MPH, the vehicle lost power steering functionality. The contact stated that excessive force was needed to maneuver the vehicle. The power steering malfunction warning light was illuminated. The…
The contact owns a 2016 Mercedes-Benz GLE450. The contact stated that while driving approximately 40 MPH, the vehicle lost power steering functionality. The contact stated that excessive force was needed to maneuver the vehicle. The power steering malfunction warning light was illuminated. The contact had not taken the vehicle to a certified mechanic to be diagnosed or repaired. The contact stated that the failure was related to NHTSA Campaign Number: 17V241000 (Steering). The manufacturer was made aware of the failure and informed the contact that the Year/Make/Model was not included in the recall. The approximate failure mileage was 110,000.
- Electrical system · Fuel/propulsion system · Vehicle speed control
Shifter and speed control car goes into nuetral instead of drive. The car excessively breaks when not necessary. Car stalling and locking steering wheel constant clicking after driving coming from the fuel tank. I use premium gas always the best quality. Problems with the control modules saying…
Shifter and speed control car goes into nuetral instead of drive. The car excessively breaks when not necessary. Car stalling and locking steering wheel constant clicking after driving coming from the fuel tank. I use premium gas always the best quality. Problems with the control modules saying transmission not in park will roll away but car is in park the car automatically going into modes without prompt showing on dash. Tow engaging without print. It’s ver scary. Please fix these glitches. My car was off the road by and in safe driver as I got back into the road m. Thus is hie The accident Happened my car locked and cut off ion the road and when I tried to turn my steering wheel I was hit. My car stalled and steeering wheel locked.
- Electrical system · Unknown or other
The passenger side door won't open or lock automatically
- Electrical system · Engine
Battery and antitheft device malfunction causing inability to shift out of neutral and can roll of the road. I left car immediate due to the risk of rolling into traffic without control called for help and secured with blocks. Not confirmed yet by dealer....no warning prior to failure....car is…
Battery and antitheft device malfunction causing inability to shift out of neutral and can roll of the road. I left car immediate due to the risk of rolling into traffic without control called for help and secured with blocks. Not confirmed yet by dealer....no warning prior to failure....car is secured waiting for tow for 2 days to the dealership...the keys dont work ..it was a very dangerous situation and other mercedes have encountered this problem noted on line the mercedes dashboard ..
- Structure › Body
TL* the contact owns a 2016 mercedes-benz gle450 AMG. The contact stated that the front wheel well liner pin/screw on both the driver and passenger sides were loose, which caused the wheel liner to make contact with the tires while driving the vehicle. The vehicle was not diagnosed or repaired.…
TL* the contact owns a 2016 mercedes-benz gle450 AMG. The contact stated that the front wheel well liner pin/screw on both the driver and passenger sides were loose, which caused the wheel liner to make contact with the tires while driving the vehicle. The vehicle was not diagnosed or repaired. Mercedes-benz of buckhead (2799 piedmont rd ne, atlanta, ga) and the manufacturer were notified of the failure. The failure mileage was 30,001.
- Engine · Steering · Suspension
I am experiencing issues with my active curve system, that other mb models of the same year and class are experiencing. some of the 2016 gle's have been recalled for this particular issue, but my vehicle/vin has not been included in the recall. I receive this error message when turning a curve.…
I am experiencing issues with my active curve system, that other mb models of the same year and class are experiencing. some of the 2016 gle's have been recalled for this particular issue, but my vehicle/vin has not been included in the recall. I receive this error message when turning a curve. my vehicle IS under warranty and mb will not pay for this with my cpo warranty. The dealership has quoted me $6984.00 to fix the issue. please investigate this matter because I think that my vehicle/vin should have been included with the current recall campaign number 18v27200. my active curve system has been leaking oil. I am concerned as this IS a fire hazard and safety issue. I can smell the oil burning as well as see it foaming from the fluid canister.
- Engine · Fuel/propulsion system
Car stalled on the highway then towed to the dealership. Dealership stated the fuel line was flooded with water. The service manager stated that I let the trunk open in the rain, but I did no such thing. There was also no water in the trunk of the car. This seems to be a defect when the vehicle IS…
Car stalled on the highway then towed to the dealership. Dealership stated the fuel line was flooded with water. The service manager stated that I let the trunk open in the rain, but I did no such thing. There was also no water in the trunk of the car. This seems to be a defect when the vehicle IS exposed to normal rainy conditions. There IS no way water should be able to get to the fuel line because it should be insulated against moisture. Corporate thought there was flooding in the area, but there IS no flooding in dallas, texas. Mb conducts quality testing in different climates so I do no see why they would not consider it to be a product defect. someone can potentially die from the car stalling on the highway. This IS something that should not be overlooked by mb.
- Structure › Body
My sunroof exploded spontaneously while I was driving. There was no signs of damage to the glass. The glass flew back on road and the glass remaining on too appeared bowed.
- Power train
Car lurches forward during braking causing the car to shutter and buckle forward without control.issues occurs in all modes of drive, including eco, sport, sport+ and comfort. When approaching a stop the car jerks forward while brakes are applied. Rpm's boost up without any motion on the gas pedal…
Car lurches forward during braking causing the car to shutter and buckle forward without control.issues occurs in all modes of drive, including eco, sport, sport+ and comfort. When approaching a stop the car jerks forward while brakes are applied. Rpm's boost up without any motion on the gas pedal and subsequent motion on the brake. Car lunges forward causing whiplash and loss of control at speeds under 20 mph. Car has had this specific transmission issues since purchase in 9/2016 and dealership has dealt with this issue on the same make and model without avail. Car has been in for service since 11/2/2017 without any update, 30+ days in state of california (automatic lemon law applies). Car needs a software fix that hasn't been issued yet, and will not be issued until the earliest mid-january 2018. when first brought in for service (4 weeks after purchase) dealer stated the car was "breaking in", I had to tell the dealership that I wouldn't pay them for scheduled maintenance if they could not fix the transmission issue they kept the car and still have it .mercedes north america - special reference to the west coast referral manager has been uncooperative in responding to requests for information and does not respond to any communications.
- Steering
TL* the contact owns a 2016 mercedes-benz gle450. The contact received notification of nhtsa campaign number: 17v241000 (steering); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The…
TL* the contact owns a 2016 mercedes-benz gle450. The contact received notification of nhtsa campaign number: 17v241000 (steering); however, the part for the recall repair was unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called critz BMW buick GMC mercedes-benz of savannah who informed them that the part was not available. The manufacturer informed the contact that they would receive a second notice once parts were available. The contact had not experienced a failure. Vin tool confirms parts not available.
- Electrical system
TL* the contact owns a 2016 mercedes-benz gle450. After the vehicle was repaired per nhtsa campaign number: 16v440000 (electrical system), the vehicle experinced a failure. When the contact depressed the brake pedal, the vehicle completely shut off. The contact restarted the vehicle, but the…
TL* the contact owns a 2016 mercedes-benz gle450. After the vehicle was repaired per nhtsa campaign number: 16v440000 (electrical system), the vehicle experinced a failure. When the contact depressed the brake pedal, the vehicle completely shut off. The contact restarted the vehicle, but the failure recurred. The vehicle was taken to walter mercedes in riverside, california, but the cause of the failure could not be diagnosed. The manufacturer stated that the recall was repaired and could not be duplicated. The approximate failure mileage was 18,407.
- Engine
Eco start/stop feature IS unsafe. driver could misinterpret when vehicle IS in eco stop mode vs off in park. this could cause the vehicle to start and lurch forward when the driver takes their foot off the brake when they assume it IS off in park. unsafe.
- Wheels
Continental tire failure. With about 500 miles from taking delivery tire developed a bubble on the outside. Creating high probability of failure in florida heat. tire replaced by mercedes.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010750Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to FIN vehicle identification end number. If vehicle falls outside of FIN range, create a TIPS case. Model series 192: xxx xxx xx 002 876 Model series 232: xxx xxx xx 022 312 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11010644Complaint Paint damage on door paneling in area of door handle (see picture 1). Cause Possible tolerance complaint regarding the door handle Remedy 1. Paint the affected area of the door paneling using the spot repair procedure in accordance with the manufacturer's specifications. 2. Replace door handle, ensuring that the door handle bearing bracket is installed correctly (see picture 2). Note: The optimized door handles are marked as shown in the illustration (see picture 3).
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11009036Complaint "Active Emergency Stop Assist Currently Unavailable" and "Active Steering Assist Inoperative" instrument cluster messages along with Tire Pressure Light on in Instrument Cluster. Cause Both systems are temporarily unavailable due to low tire pressures. An active tire pressure monitor light may result in some assistance features being temporarily unavailable until tire pressures are corrected. Remedy Check/adjust tire pressures and reset monitoring through the instrument cluster.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008070Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause Contact area between wheel bearing and steering knuckle. Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present, perform Operation A again. 3. If noise is still present after re-testing, perform Operation B. Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing and steering knuckle with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). Operation B: 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10208744Complaint The touchpad dimming function does not work and the search lighting is either at maximum brightness or fully off (dependent upon dimming signal). Note: The dimming functions of the instrument cluster and head unit display are not affected and remain fully functional. Cause Touchpad (A105) hardware Remedy The serial numbers of the potentially affected parts can be found in the attached list. The serial number can be found on the touchpad itself or in Vedoc (Vedoc -> control units -> TPAD -> serial number). If the serial number listed in VeDoc or on the part (these numbers should be identical) matches one of the serial numbers in the attachment and the described complaint is present, then the touchpad may be replaced.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205835Model series 167 noise on B/C/D pillars.
- 10205819Important new emission service campaign information.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205256Correct torque front left and right torsion bar linkage nut.
- 10205251Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205250Engine fan runs continuously, a/c inoperable or, engine light illuminates sporadically.
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205154Gasket may settle causing a slight oil leak.
- 10205147Ticking or pulsing noise from high-pressure pump and/or fuel injectors.
- 10202531Touch pad: Search lighting does not dim or does not turn on.
- 10199774Launch NCU 2021070020- Perform SCN coding in powertrain control unit
- 10195220For plug in hybrid and electric variants: Complaints about the electric range
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
- 10184798Replace charge air hose between charge air cooler and turbocharger
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
Every Mercedes-Benz GLE450 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.