2013 Mercedes-Benz GLK250
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLK250 › 2013
These records cover every 2013 Mercedes-Benz GLK250. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
6 recalls name the 2013 Mercedes-Benz GLK250. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 GLK250 vehicles equipped with 4-cylinder diesel engines. The incorrect type of transmission fluid filter and overflow pipe may have been installed during a service repair, which could result in a transmission fluid leak or control module failure.
Risk and remedy
Risk
A transmission fluid leak can increase the risk of a fire. In addition, a transmission control module failure could result in a vehicle stall, increasing the risk of a crash.
Remedy
Dealers will replace the overflow pipe and transmission fluid filter, free of charge. Owner notification letters were mailed on September 3, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of…
Risk and remedy
Risk
A loss of steering can increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
6 complaints
What owners report most
Latest complaints
- Unknown or other
Driving home mid morning Thursday , March 5, 2026 on smooth paved rural road, 50MPH, sunny, temp was 40 degrees, no vehicles anywhere near us, our Panoramic Sunroof shattered on our 2013 Mercedes GLK 250. We heard a loud "BANG", but had no idea what it was. I slowed down, pulled over and while…
Driving home mid morning Thursday , March 5, 2026 on smooth paved rural road, 50MPH, sunny, temp was 40 degrees, no vehicles anywhere near us, our Panoramic Sunroof shattered on our 2013 Mercedes GLK 250. We heard a loud "BANG", but had no idea what it was. I slowed down, pulled over and while looking up, I noticed the sunroof had completely shattered and cracks were spreading as we sat watching it. I drove home short distance and parked the GLK in the garage. There are no visible signs of an impact to the glass exterior nor interior. To keep it from falling into the cab, I taped the inside and outside with clear packing tape. The vehicle is out of warranty and we don't have comp nor collision on it anymore due to it's age. While researching for glass replacements, I found that there are numerous Class Action Lawsuits for this issue. This is a very dangerous defect and safety issue as when the glass shattered, it was as loud as a shotgun blast and very unnerving. The vehicle is currently undriveable and unsafe.
- Power train
The contact owns a 2013 Mercedes-Benz GLK250. The contact received notification of NHTSA campaign number: 21V539000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact…
The contact owns a 2013 Mercedes-Benz GLK250. The contact received notification of NHTSA campaign number: 21V539000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced the failure. VIN tool confirms parts not available.
- Air bags
TL* the contact owns a 2013 mercedes-benz glk250. The contact received a recall letter for nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. An unknown mercedes dealer was contacted and confirmed that…
TL* the contact owns a 2013 mercedes-benz glk250. The contact received a recall letter for nhtsa campaign number: 19v010000 (air bags). The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. An unknown mercedes dealer was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was made aware of the issue and was not able to confirm when the parts were to become available. The contact had not experienced a failure. Vin tool confirms parts not available.*cw *dl
- Air bags
TL* the contact owns a 2013 mercedes-benz glk250. The contact stated that the vehicle was included in nhtsa campaign number: 18v043000 (air bags). Vonhousen automotive group (1810 howe ave, sacramento, ca 95825, 888-479-0451) stated that the part was not available. The manufacturer was not…
TL* the contact owns a 2013 mercedes-benz glk250. The contact stated that the vehicle was included in nhtsa campaign number: 18v043000 (air bags). Vonhousen automotive group (1810 howe ave, sacramento, ca 95825, 888-479-0451) stated that the part was not available. The manufacturer was not contacted. The vehicle was not repaired. The contact had not experienced a failure. Vin tool confirms parts not available. *bf*jb
- Unknown or other
Adblue def heater and nox sensors . My def fluid / adblue heater developed a code at 113K miles and and the same time a nox sensor code. The dealer replaced the nox sensors for $2500 and the def heater code has come back. The vehicle IS highway driven and should not have these emission codes. The heater replacement will cost another $3000 or more
- Unknown or other
Driving 45-50 mph on the road alone and am startled by loud noise which resembled a gunshot. I immediately checked the dash to see if any warning lights were illuminated but saw nothing. after a few minutes I looked up and noticed my panoramic sunroof what shattered in tiny pieces. dealership…
Driving 45-50 mph on the road alone and am startled by loud noise which resembled a gunshot. I immediately checked the dash to see if any warning lights were illuminated but saw nothing. after a few minutes I looked up and noticed my panoramic sunroof what shattered in tiny pieces. dealership stated that "no outside source found causing damage" to the sunroof. car IS under and extended warranty and manufacture has refused to take responsibility for the issue.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10243308Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction The partial-load ventilation valve (a part of the intake line assembly) may not work as intended Performed guided test for fault code P052E71. Replace intake line assembly if necessary per results of the guided test. Do not perform software update of N3/10 Engine control unit at this time. This LI will be updated once the software solution is available. This LI is in relation to NCU dated 8/31/2023 "Emission Extended Warranty Intake Line Assembly".
- 10235978Recall Campaign announcement for Takata driver airbags.
- 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
- 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
- 10232319Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2012-2016 E-Class, GL-Class, GLE-Class, GLK-Class, and ML-Class (166, 204, 212 platforms) vehicles, the coding of the control units for selective catalytic reduction (SCR) and fully integrated transmission control (VGS) do not correspond to the specifications as part of the BlueTEC update diesel field measure. This could result in the CAL ID (Calibration ID) not being read out from the vehicle and re-documented in the relevant systems. This situation does not have any additional technical implications for the vehicle. What Were Doing MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the SCN coding for SCR and VGS on the affected vehicles.
- 10227152Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2013-2016 E/GLK/GLE/M-Class vehicles, the software for the water pump diagnostics may not correspond to current specifications. This issue has an extremely low rate of occurrence in the field and has no known emissions or fuel economy impact. However, in the rare instance this issue does occur in a vehicle, it may prevent the vehicle from passing certain state inspection requirements (e.g., California SMOG check). What Were Doing MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the software for the water pump diagnostics on the affected vehicles.
- 10219253Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) vehicles listed below, the particulate matter (PM) sensor could potentially fail and consequently activate the malfunction indicator light (MIL) with one of the fault codes mentioned below. As a result, the warranty for the PM sensor has been extended from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 10 years / 120,000 miles (whichever occurs first).
- 10219242Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2012-2016 GLK-Class, E-Class, ML-Class, GLE-Class, and GL-Class (204, 212 and166 platforms) vehicles, an incorrect NOx sensor, Diesel Particulate Filter (DPF), Selective Catalytic Reduction (SCR) catalyst and/or Particulate Matter (PM) sensor may have been installed, which may not correspond to the specifications set forth in the BlueTEC update Approved Emission Modification (AEM) program. The incorrect hardware may potentially result in increased exhaust gas emissions. What Were Doing MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will check and replace (if necessary), the necessary exhaust system hardware on the affected vehicles
- 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
- 10205265Outside mirror fogged.
- 10205248"SOS mbrace service not activated".
- 10205247Traffic information service and posibly the voice control, nonfunctional after navigation software update.
- 10205236"Metadata loss- Please reimport all media data".
- 10205233Mobile phone cotacts are not transferred completely.
- 10205225Headlamps fogged.
- 10205215Window lifter and outside mirror on passenger side malfunction after replacement of door control unit.
- 10195219modifying emissions control system on certain diesel vehicles
- 10187793Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software
- 10184797Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain Mercedes-Benz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or caused to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed.
- 10181195Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10167547Shift quality complaints and/or automatic transmission in limp-home mode in combination with one or more of the following fault codes: P060600, P072200, P072300, P072364, P072900, P073000, P073100, P073200, P073300, P073400, P073500, P076F00.
- 10167085Passenger side wiper arm strikes vent grille of water collector
- 10167040This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
- 10166977Engine diagnosis warning lamp lights up. The fault code (FC) P0101FA or P0101Fb or P0101FC is logged in the engine control unit.
- 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
- 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
- 10135598Engine diagnosis warning lamp lights up in instrument cluster, fault code U145400: "Implausible data were received from the ethanol sensor"
Every Mercedes-Benz GLK250 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.