2022 Mercedes-Benz GLS 450 4MATIC
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › GLS 450 4MATIC › 2022
These records cover every 2022 Mercedes-Benz GLS 450 4MATIC. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
10 recalls name the 2022 Mercedes-Benz GLS 450 4MATIC. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2023-2024 GLE 350, 2020-2024 GLE 450, 2020-2023 GLS 580, GLE 580, 2019-2023 GLS 450, 2021-2023 Maybach GLS 600, AMG GLS 63, 2021-2024 AMG GLE 53, AMG GLE 53 Coupe, and AMG GLE 63 S vehicles. A 48-Volt ground connection under the passenger seat may not be secured properly, resulting in the ground…
Risk and remedy
Risk
An overheated ground connection can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the 48-Volt ground connection as necessary, free of charge. Owner notification letters were mailed on May 3, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2024040002.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2023 GLE 450 and GLS 450 vehicles. The transmission may not fully downshift in certain conditions, causing the engine to stall.
Risk and remedy
Risk
An engine stall increases the risk of a crash.
Remedy
Dealers will update the transmission control unit software, free of charge. Owner notification letters were mailed March 29, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2024 GLE, GLS, C-Class, E-Class, S-Class, SL, GLC, CLS, AMG GT, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, causing a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 28, 2024. Owner notification letters will be mailed in phases, on February 23, 2024, April 19, 2024, June 28, 2024, August 9, 2024, October 1, 2024, and December 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 23V-445.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2023 C-Class, E-Class, S-Class, CLS, SL, GT, GLC, GLE, GLS, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle details. The fuel pump may shutdown, which can result in a loss of drive power.
Risk and remedy
Risk
A loss of drive power can increase the risk of a crash.
Remedy
Dealers will replace the fuel pump, free of charge. Owner notification letters were mailed on June 14, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2023070012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 GLE350, GLE450, GLE580, GLS450, GLS580, Maybach GLS600, AMG GLE53, AMG GLE63 S, and AMG GLS63 vehicles. The rear door window trim bars may detach from the vehicle while driving.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed May 5, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of previous recall number 22V-680. MBUSA's number for this recall is 2023040011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021-2022 GLE350, GLE450, 2022 AMG GLE53, AMG GLE63, and GLS450 vehicles. The steering coupling locking screw may loosen and possibly detach from the steering gear, resulting in a loss of steering control.
Risk and remedy
Risk
A loss of steering control can increase the risk of a crash.
Remedy
Dealers will replace the steering coupling locking screw, free of charge. Owner notification letters were mailed January 27, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022120016.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2021 AMG GLS63, 2020-2022 GLS450 and GLS580 vehicles. Due to a manufacturing error, the locks on the third-row seatbacks may fail in the event of a crash.
Risk and remedy
Risk
A seat with a seatback lock failure may not properly restrain occupants, increasing the risk of injury during a crash.
Remedy
Dealers will inspect and replace the third-row seatback, as necessary, free of charge. Owner notification letters were mailed November 18, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022100011.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE350, GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, and 2021 GLE400e, AMG GLS63, AMG GLE63 S, and Maybach GLS600 vehicles. Due to a manufacturing error, the rear door window trim bars may detach.
Risk and remedy
Risk
Detached trim bars may cause a road hazard and increase the risk of a crash or injury.
Remedy
Dealers will inspect and secure the rear window trim bars, as necessary, free of charge. Owner notification letters were mailed November 1, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090010.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2022 GLE450, GLS450, 2021-2022 AMG GLE53, 2020-2021 GLE580, GLS580, 2021 AMG GLE63, Maybach GLS600 and AMG GLS63 vehicles. A ground cable bolt for the 48V ground connection under the front passenger seat may not be secured properly, which can cause the electrical cable to overheat.
Risk and remedy
Risk
An overheated electrical cable can increase the risk of a fire.
Remedy
Dealers will inspect and tighten the ground cable bolt, as necessary, free of charge. Owner notification letters were mailed July 8, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040017.
Owner complaints
17 complaints2 involved a crash1 involved a fire
What owners report most
Latest complaints
- Unknown or other
My car was part of a recall campaign in 2022/2023 (22V68000 and [XXX]). The car was inspected and it was determined that no repair was needed at the time. Earlier this year, XXX, the rear window trim fell off while I was driving on the freeway ([XXX] near [XXX]). I reported this to Mercedes Benz…
My car was part of a recall campaign in 2022/2023 (22V68000 and [XXX]). The car was inspected and it was determined that no repair was needed at the time. Earlier this year, XXX, the rear window trim fell off while I was driving on the freeway ([XXX] near [XXX]). I reported this to Mercedes Benz of [XXX]. On XXX, they charged me $969.36 to replace the window trim. There was no mention of the previous recall, and no deep investigation was done as to why the trim fell off. On XXX less than 3 months after the replacement, the same piece of window trim fell off again while I was driving on the freeway ([XXX] in [XXX]). My attempts to speak with a service manager were not responded to. I emailed the General Manager, [XXX], who called me 2 days later. She said they would replace the trim for free. Upon reviewing my paperwork from previous service appointments, I found the information regarding the recall campaign. I brought this to [XXX]'s attention, and requested both a thorough investigation of the car door and window to assure the proper repair, and also a refund of what I was illegally charged in XXX for the replacement of a known recalled issue. I told her that I would not bring my car in for a simple trim replacement piece as the car still poses a safety hazard. She did not, and still has not, responded to my request. The only warning/symptom of this issue is that I originally reported hearing wind through the closed window at my 10,000 mile service. This complaint is dated 9/08/2022 on the paperwork that I have, but my mileage was recorded as 12,145. The service technician stated that they could not replicate the sound during evaluation. it is clear that the original inspection for the recall campaign was not carried out properly. Additionally, Mercedes is ignoring my request to re-open the recall on my car and repair it thoroughly to avoid another freeway incident of flying trim. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Fuel/propulsion system · Power train · Unknown or other
The vehicle suffered a total internal transfer case mechanical failure at 22,909 miles, which was documented during a factory-scheduled Service B check. The dealership attempted a fluid flush, which immediately resulted in an active 4MATIC system failure warning on the dashboard. Complete…
The vehicle suffered a total internal transfer case mechanical failure at 22,909 miles, which was documented during a factory-scheduled Service B check. The dealership attempted a fluid flush, which immediately resulted in an active 4MATIC system failure warning on the dashboard. Complete mechanical failure of this 4MATIC component causes extreme drivetrain binding and wheel hopping during low-speed maneuvers, presenting a major vehicle control hazard and a high risk of sudden loss of propulsion while driving on public roads.
- Service brakes
I am writing to formally log an urgent Safety-Critical Incident Report regarding a complete brake system failure on my 2022 Mercedes-Benz GLS450 (VIN: [XXX]). Incident Details: Date & Time：［XXX］ Vehicle Mileage: Approximate 30k miles Occupants: 5 family members (including 3 children)…
I am writing to formally log an urgent Safety-Critical Incident Report regarding a complete brake system failure on my 2022 Mercedes-Benz GLS450 (VIN: [XXX]). Incident Details: Date & Time：［XXX］ Vehicle Mileage: Approximate 30k miles Occupants: 5 family members (including 3 children) Maintenance History: Fully and regularly maintained according to manufacturer schedules. What Happened: While driving with my family on the highway, the brake pedal suddenly went completely soft and lost braking power, creating an extremely dangerous, life-threatening situation. The dashboard did not display any advance warning before the failure occurred. Fortunately, I was able to safely coast the vehicle to the shoulder using emergency deceleration. Inspection under the vehicle indicated a severe brake fluid leak/hydraulic pressure loss. The vehicle had to be towed directly to an authorized dealership Enterprise Motorcar [XXX] Our Demands & Requests: As a 2022 model with low mileage and proper maintenance, a sudden failure of a fundamental safety component like the hydraulic braking system—without prior sensor warning—is completely unacceptable and points to potential manufacturing or material defect. I request MBUSA to take the following actions immediately: Open a Formal Safety Case: Assign a dedicated Case Manager to investigate this failure. Comprehensive Diagnostic Report: Coordinate with the dealership to conduct a full root-cause analysis on why the hydraulic line/system ruptured and why no warning light was triggered beforehand. Full Warranty / Defect Coverage: Ensure all repair costs, parts replacements, and associated towing expenses are 100% covered by Mercedes-Benz. Loaner Vehicle / Mobility Support: Provide a comparable loaner vehicle for our family while our vehicle is under inspection and repair. Please confirm receipt of this email and provide me with a MBUSA Safety Case Number at your earliest convenience. Sincerely INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C
- Forward collision avoidance › Automatic emergency braking · Lane departure › Assist
I have been receiving errors that visibility is reduced. Lane departure system is not working and car has brake suddenly in moderate traffic despite not being close to vehicle ahead of me.
- Visibility › Sun/moon roof assembly
The contact owns a 2022 Mercedes-Benz GLS450. The contact stated that while driving at an undisclosed speed, there was an abnormally loud sound coming from the roof of the vehicle. The vehicle was pulled over to the shoulder lane and the contact discovered that the sunroof glass had shattered. No…
The contact owns a 2022 Mercedes-Benz GLS450. The contact stated that while driving at an undisclosed speed, there was an abnormally loud sound coming from the roof of the vehicle. The vehicle was pulled over to the shoulder lane and the contact discovered that the sunroof glass had shattered. No warning lights were illuminated. A dealer was contacted, and the dealer suggested that the insurance provider be contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 50,000.
- Forward collision avoidance › Automatic emergency braking
Car has been auto braking even though there is nothing in front of the car. This is extremely dangerous and could lead to serious rear end collisions. There are many similar complaints on online forums and Mercedes (and their lawyers) do nothing. Link to video: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Unknown or other
The vehicle caught fire while parked and running in the driveway of my home. There were no modifications, no accident, and no external cause. The fire occurred without warning and posed a serious safety risk to occupants and property. The vehicle was under manufacturer warranty at the time of the…
The vehicle caught fire while parked and running in the driveway of my home. There were no modifications, no accident, and no external cause. The fire occurred without warning and posed a serious safety risk to occupants and property. The vehicle was under manufacturer warranty at the time of the incident. The fire caused damages to my house too. There were no warning lamps or messages. Benz has not done an investigation yet.
- Forward collision avoidance › Adaptive cruise control · Forward collision avoidance › Automatic emergency braking · Vehicle speed control
The car has on 5+ occasions had the collision avoidance system shut down (photos of dash showing this are available and have been shared with the dealer). There were no weather incident at the time. Lane following........ same type of thing also shared with dealer. Most disturbing is on multiple…
The car has on 5+ occasions had the collision avoidance system shut down (photos of dash showing this are available and have been shared with the dealer). There were no weather incident at the time. Lane following........ same type of thing also shared with dealer. Most disturbing is on multiple occasions, with the speed control engaged driving on the interstate at 65 to 70 mph, the speed limit indicator on the dash changed to 40 (no speed limit change) and the car went into hard breaking mode until I disengaged the system. (also reported to dealer) Each time the car went into the shop, they "checked the systems" and found no faults and made no repair except on one occasion, they "flashed" the software. The car went into the dealer with 67,000 miles on June 3, 2025 with a promise that they would get to the bottom of this issue. The car was returned after a full "testing" and for good measure, one software update and the replacement of a forward facing camera lens. For each item submitted, they reported no history of any faults and found nothing wrong with the car. The car was returned [XXX] at [XXX]. On [XXX] going 60 mph in traffic, the speed limit indicator jumped to 80 mph and the car immediately and rapidly accelerated until I shut the system down. I took a photo of the dash showing the 80 MPH indication. There are NO locations in Virginia that have an 80 mph speed limit. Also, on several occasions, an alert comes up the the car has been in an accident..... when parked in my garage and a bogus date. Other software glitches happen on a periodic basis INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Engine · Fuel/propulsion system · Power train
Vehicle lost power while driving on a busy freeway and came to a complete stop and would not restart resulting in it being struck by a vehicle in the rear. More information available in the collision center pre estimate scan and full estimate.
- Electrical system · Power train · Service brakes
While backing out of steep driveway, the car computer screen blinked saying "updating" then screen went blank, lost power, I could not brake. We have a row of trees at the back of our driveway that stopped the car ( with damage) or else we would have rolled into our neighbors basement all. Tree…
While backing out of steep driveway, the car computer screen blinked saying "updating" then screen went blank, lost power, I could not brake. We have a row of trees at the back of our driveway that stopped the car ( with damage) or else we would have rolled into our neighbors basement all. Tree limbs poked a hole in bumper, cracked left tail light, and damaged the back hatch. Mercedes is saying User fault. I have been driving for 45 years without a ticket, wreck or causing an accident, and I am not a liar. If this blanking of the computer screen happened on a highway , a whole family could be killed, or caused a MULTI-car accident. I am concerned about OTHERS welfare. sent 8/17/2024
- Electrical system · Engine · Vehicle speed control
As I approached a red light and removed my foot from the gas pedal to brake, my dashboard displayed several alarming messages: “Active Brake Assist Functions Limited See Owner's Manual,” “Active Blind Spot Assist Inoperative,” “To Deselect P or N Depress Brake and Start Engine,” and “Traction…
As I approached a red light and removed my foot from the gas pedal to brake, my dashboard displayed several alarming messages: “Active Brake Assist Functions Limited See Owner's Manual,” “Active Blind Spot Assist Inoperative,” “To Deselect P or N Depress Brake and Start Engine,” and “Traction Control Inoperative See Owner's Manual.” Subsequently, all dashboard lights illuminated, the engine turned off, and the car shifted into neutral from drive, preventing me from restarting it. Despite turning on my hazard lights, I was stuck in the middle lane while the light turned green. My husband recorded the event on his phone. Eventually, the car restarted, and we continued to his doctor’s appointment. After the appointment, which lasted approximately 45 minutes, I noticed the check engine light was still on when we got into the car. Despite this, I drove home and then to the dealership, where I explained the situation and showed the video to the service writer. Later that day, our service writer informed me via text that there were “No faults in system that would indicate issue that would cause vehicle stalling” and suggested a transmission update recall might be related. I requested the code for the check engine light but was told “no code stored for check engine light.” Given these circumstances, I have several pressing concerns: My car turned off in the middle of a busy street and wouldn’t restart immediately, creating a hazardous situation. This incident poses a significant safety risk. What if this had occurred on a freeway or my daughters were driving my car? The dealership's assertion that no issues were found is hard to believe given the clear malfunctions and present check engine light. Mercedes-Benz's response has not addressed my concerns about the vehicle's safety. A car should not "just turn off while actively driving." I am not at all comfortable with the dealership’s statement that “sometimes this can just happen.” This should NEVER happen
- Power train
While driving it goes to neutral by it self
- Forward collision avoidance › Warnings · Unknown or other · Wheels
The car radar system apparently had a glitch and locked up the wheels while I was driving 25 mph. Yes, it is available for inspection. We are afraid to drive the car, it is just sitting. The car locked up so suddenly it made the rear wheel come off and rear of car fell to the ground. I was bruised…
The car radar system apparently had a glitch and locked up the wheels while I was driving 25 mph. Yes, it is available for inspection. We are afraid to drive the car, it is just sitting. The car locked up so suddenly it made the rear wheel come off and rear of car fell to the ground. I was bruised by the seatbelt from the sudden stop. The dealer acted like they were unable to inspect it, I had the car towed there since it is under warranty. They said it had been in an accident. It had not been in an accident. I had to have policemen direct traffic until the tow truck arrived since the car was literally stopped in the middle of the street. We had an independent shop verify the issue and replace the tire and wheel that had fallen off. The car has had multiple warning messages about active brake assist inoperable, engine overheating, etc. The dealer has not been responsive at all. Seems they are trying to dodge responsibility.
- Unknown or other
I heard a very loud boom. It scared me. The sunroof exploded. I did not see anything in the road or any object flying toward me. Then I heard cracking and the sunroof started falling in above me. Thankfully, the fabric cover kept the glass from falling on me. Otherwise, the glass would have…
I heard a very loud boom. It scared me. The sunroof exploded. I did not see anything in the road or any object flying toward me. Then I heard cracking and the sunroof started falling in above me. Thankfully, the fabric cover kept the glass from falling on me. Otherwise, the glass would have fallen on me. I could see pieces of glass. I pulled over and looked at the glass. I started towards my home and the shattered glass started flying off behind me and towards the car behind me. I did not want it to cause issues for them so I slowed down to about 30 mph so the glass would not continue to crack and fly off behind me and put on my hazard lights. My daughter called within 30 sec to a minute after it happened. She said when I clicked on the phone (through the car speaker) she heard me say a few words and the cracking of the glass. She called at 4:17 on May 24th, 2023. It was a clear sunny day. When my husband looked at the sunroof and noticed the glass coming up as opposed to caving in. So he said something did not fall through it it had to explode. We did call the dealership and they said they did not have an appointment until June 6th. My husband said we would have to clean up and take most of the glass out to be able to drive it. We did that and put cardboard over it so bugs could not get it. There was no damage to any other part of the windshield or car.
- Engine
Car went into limp mode which causes loss of acceleration on major highway. This same issue of going into limp mode happened August of 2022 when the vehicle has less than 1000 miles. The car has 5750 miles and the temperature gauge showed yellow. Then the the yellow engine light came on and then the car went into limp mode where the engine loses power.
- Electrical system · Unknown or other
I had been driving the car for about ten minutes when the 48v battery malfunction light came on. Within seconds, another warning appeared that said coolant was too hot, and the acceleration stopped accelerating and then went to a complete stop in the middle of the road. I didn't have time to pull…
I had been driving the car for about ten minutes when the 48v battery malfunction light came on. Within seconds, another warning appeared that said coolant was too hot, and the acceleration stopped accelerating and then went to a complete stop in the middle of the road. I didn't have time to pull over. It was dark and we were completely stalled. I turned the car off, put my hazards on, and waited a minute. When I restarted the car, it worked fine and I was able to make it home. If this had happened on the interstate, I would not have had time to make it to the side of the road. The car only has 25,000 miles on it.
- Electrical system · Vehicle speed control › Accelerator pedal
The contact owns a 2022 Mercedes-Benz GLS450. The contact stated that while his wife was driving approximately 35 MPH, the vehicle lost motive power and stalled. Additionally, the power steering was inoperable. There were several unknown warning lights illuminated; in addition to the check engine…
The contact owns a 2022 Mercedes-Benz GLS450. The contact stated that while his wife was driving approximately 35 MPH, the vehicle lost motive power and stalled. Additionally, the power steering was inoperable. There were several unknown warning lights illuminated; in addition to the check engine warning light being illuminated. The driver was able to pull over safely stop after coasting the vehicle. The vehicle was restarted; however, the check engine warning light remained illuminated. The vehicle was driven to the dealer. The dealer diagnosed the failure with the accelerator pedal, pin connector, and an unknown electrical failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 200. The VIN was not available.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010970Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY21-25 C-Class, CLA, EQB, EQE, EQS, G-Class, GLA, GLB, GLC, GLE, GLS, GT, S-Class, and SL (206, 118, 243, 294, 296, 465, 247, 254, 167, 192, 223, and 232 platform) vehicles, the MBUX multimedia system does not correspond with the latest series production configuration. The MBUX multimedia system control unit will receive an OTA software update. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010744Complaint Engine cooling fan running for an extended time after switching off vehicle. Cause Optimized thermal management in latest PTCU software. Remedy This is a normal function in the latest PTCU software. Engine fan will operate for up to 20 minutes after ignition is switched off. Note: Repair work should only be performed if a clear malfunction is identified
- 11010652Complaint One or more of the seats in the second or third row cannot be folded over when the switch group in the trunk is used. Cause Under analysis. Remedy Please thoroughly check the physical layer such as operating switches, lines, and pins to make sure that they are not the reason for the fault. Verify the switches are showing correct actual values with the Xentry. Verify the seats fold properly when using other switches. After this, create a TIPS case and attach a control unit log for the corresponding control unit along with a CAN trace from the body CAN that documents the problem.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11010450Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy Update of head unit A26/17 to the new software: E504.5 (A 297 904 09 01)
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11010437Complaint Automatic window raising function of side window inoperative. Cause Denormalization of the window lifter system. Remedy Update the software in the affected door control unit (N69/x). This requires the door control unit (N69/x) to be commissioned. (Path: XENTRY -> Control units view -> DCU-XX (N69/x) -> Adaptations -> Commissioning) SW item numbers of the repair software: A1679023716 for the door control units on the front doors (N69/1 and N69/2) A1679023816 for the door control units on the rear doors (N69/3 and N69/4)
- 11009550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Do NOT remove the expansion valve from the evaporator prior to being advised to in a TIPS case. 2. Initial Quick Test 3. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 4. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 5. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 6. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 7. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 8. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 9. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008882Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : Remedy 1 (Only applies to vehicles produced during or prior to June 2023) 1. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 2. Clear picture of VIN on B-pillar. 3. Ensure that the rest of the AC system has been thoroughly checked for leaks before condemning the evaporator. Remedy 2 (Applies to all 167's produced after June 2023) 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with RO that shows the VIN clearly in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007969Complaint When using the offroad display in the MBUX, the "Transparent hood" function cannot be activated using the camera symbol. Cause MBUX FUP5 software: E504.3 (A 297 904 97 00) E504.4 (A 297 904 03 01) Remedy The remedy is currently being developed.
- 11007857Complaint Customer concern of Air Conditioning not cooling. Note: For vehicles produced during or prior to June 2023, a TIPS case is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. ALL steps, with the exception of videos, should be documented and uploaded with the claim submission. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. Open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. "NO TIPS case needed on vehicles during or prior to June 2023"
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11007673Complaint Damage or discoloration to paint protection films on vehicle. Cause Chip protection films are a wear item that may need to be replaced over the life of the vehicle. They are typically not covered by vehicle warranty. Remedy To properly install a paint/chip protection film, please follow the below guidelines: #1 - Utilize a solution that is 0.2% soap solution (1,000ml of water + 2ml of liquid soap). #2 - Clean the paint surface and ensure it is dust-free. #2a - When cleaning, you can utilize isopropyl alcohol (Rubbing Alcohol) to assist with cleaning. #2b - We recommend a lint-free rag for secondary dusting. #3 - Wet hands with the soapy water solution to protect the adhesive surface. #4 - Remove the backing paper from the film completely. #5 - Moisten the vehicle surface with the soapy water. You can also lay the protective film with adhesive side out onto the wetted surface to also cover the adhesive layer in the soapy water solution. #6 - Remove film and flip over to gently place adhesive side against the paint surface. #7 - Working from the center out, use a squeegee to press the soapy water solution out from under the film. Use sufficient pressure to firmly press the film into the paint surface, but not an excessive amount to damage or stretch the film. #8 - Allow film and paint to "cure" until all of the moisture has evaporated. At this time the adhesive should be dried and cured enough for sufficient hold to release the vehicle.
- 11006678Complaint Head-up display permanently or sporadically unavailable - with warning message in driver display Head-up display permanently or sporadically unavailable - without warning message in driver display Display permanently or sporadically discolored and out of focus Cause Previous N133/1 - Instrument cluster (IC) control unit software. Remedy Update the N133/1 - Instrument cluster (IC) software.
- 11006550Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. Ensure that a full vacuum is pulled on the system for at least 30 minutes after replacement Condenser replacement is NOT authorized as a suitable repair in lieu of the dryer not being available.
- 11005347Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy If other fault codes related to engine fan are present, process these first. Replace engine fan with part as specified in XENTRY parts information. Group 50/015. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005334Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy Test Procedure: Perform an initial quick test with freeze frame data. Save the N179 - Hand detection system (HE) and N62/4 - Driver assistance system (SG-FAS) control unit logs. Note the fault frequency of fault codes set. Delete the N179 and N62/4 fault memory. Using both hands, "scan" the steering wheel all the way round, including the chrome molding at 6 o'clock (see Picture 1). Read out fault memory and follow steps below for any faults set. Remedy: Vehicles with control unit N179 - Hand detection system (HE): B1E7614: Check contacts and wiring harness in steering wheel by carrying out a visual check for damage, pinched areas, loose connections, etc. (examples in Figs. 2 and 3); If no damage is noted replace the N135 - Steering wheel electronics (LRE) and reassess. If fault code returns replace the steering wheel. Please check the wires and connections in the steering wheel. Afterwards, please check whether the complaint is caused by over torqued screws on steering wheel trim pieces. To do this, please loosen the screws slightly and reevaluate the situation. (Picture 4). P164456: Perform SCN coding. P1CA000: Perform an initial start-up on the N179 hand detection control unit. Faults in N62/4 - Driver assistance system (SG-FAS) control unit with U186B29, U0429E0, U042941, U042929, U042902, U0429E1: If no fault is stored in the N179 control unit: Scan steering wheel as indicated in the test procedure and check whether the fault is reproducible. If no fault code is stored in the hand detection control unit, the fault codes in the driver assistance systems control unit are precautionary messages. Software for the N62/4 - Driver assistance system (SG-FAS) is in preparation to reduce erroneous messages in the driver display.
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11003211Complaint The following event codes are logged in control unit IDC213 - N62/4 (Intelligent Drive control unit): U0401FC and U0401FD. Cause Under analysis. Remedy Neither of the two event codes is relevant for the functioning of control unit IDC213 - N62/4 (Intelligent Drive control unit) and can be ignored.
- 11003094Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures : 1. Initial Quick Test 2. Create a short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (Instructions in Attachments) 5. Video recording of the leak being found via sniffer at the R/F AC drain after removing the under dash panel. (see attached videos) 6. If the evaporator is found to be leaking via sniffer, another video needs to be uploaded (or a continuation if only making the video after checks), showing the expansion valve being checked for leaks. 7. If no leaks are found with the sniffer at the expansion valve, spray soapy water mix on the expansion valve and check for leaks. Upload a video showing the spray test and VIN. 8. If the vehicle is produced AFTER June 2023, a TIPS case is required for replacement. Please open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" with all attachments. 9. For vehicles produced during or prior to June 2023, a TIPS is not necessary. However, parts from repairs on such vehicles may be requested back for analysis at the QEC. Therefore, please follow parts disposition in NetStar. Repairs where parts are not returned per parts disposition instructions, or parts found to be NTF (no trouble found) are subject to debit. NOTE: Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. All documents, with the exception of videos need to be uploaded for the warranty claim. Videos are only needed if a TIPS case is opened. The dryer must be replaced when there is a leak in the AC system.
- 11003092Complaint Seats cannot be adjusted Seats cannot be folded Seats in the 2nd seat row cannot be locked or unlocked Normalization cannot be performed in its entirety using XENTRY Cause Various Remedy *Make sure a battery charger is connected to vehicle while performing all testing* Please perform the following checks that help to resolve most concerns: #1 - Make sure seat control units have latest software installed on them. #2 - For seat folding concerns, pay careful attention to the lock mechanism and ensure it is fully releasing. If the locking mechanism is short-stroking, please replace associated Bowden cables. #2a - Seat folding concerns can also be related to binding of the seat frame. To remedy, loosen torque off bolts holding seat frame to car. Shift seat frame and ensure there is no binding. Re-torque bolts securing seat frame to car and re-test. #2b - For 3rd row seats, you can remove the backrest cushion to expose the folding latch motor/mechanism. If the springs are loose/not-captured, then you must replace this assembly. If the assembly is not available by itself, the seat frame must be replaced (as the assembly is included in new one). #3 - For seats showing unlocked in the IC when fully locked, please check seat frame carefully for small microswitches that can be damaged. #4 - For seats moving forward but not folding upward (2nd row), please ensure the 4 small clips are still located on the inner and outer rails of the seat. If they are broken (example being passenger kicking them), the seat will not fold up.
- 11000618Customer concern of Air Conditioning not cooling. Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case in the HV/LV inbox labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000610Complaint 1. Cracking noises from the area of the rear axle 2. or a message in the instrument cluster "ESP, ABS failed". Cause Anti-cracking disk at the external joint of the side shaft at the rear axle is broken. Remedy Customer complaint due to noises: A test drive must be performed. For a precise noise analysis (localization of the noise), make use of the NVH/PICO. If the joint of the side shaft can be clearly identified as the cause (source of the noise), the following work must be performed: 1. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 2. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Customer complaint due to display message "ESP, ABS failed" in the instrument cluster: Read out the fault memory; if a rotational speed sensor of the rear axle is stored in the fault memory, the following work must be performed: 1. Check the rotational speed sensor of the affected side for damage and replace if necessary. 2. Remove the side shaft, check the anti-cracking disk, and remove the anti-cracking disk if it is broken, 3. then process the external joint as per LI35.30-P-058566 and reinstall the side shaft. After the processing is complete, an anti-cracking disk is no longer required. Note: It is not necessary to replace the side shaft.
- 11000606Complaint Message in Instrument Cluster: "Active Brake Assist function restricted". The driver assistance systems are temporarily unavailable. Note: Please note the listed fault code! Cause Rarely, it may be the case that communication is interrupted due to a brief interruption in the power supply to the LRR (B92/12) or A108 (Active Brake Assist). Remedy Perform new SCN coding at BC_R (N10/8).
- 11000597Complaint Customer concern of Air Conditioning not cooling. Cause Possible refrigerant leak at the evaporator. Remedy Perform the following measures and open a TIPS case labeled "167 Evaporator Suspected of Leaking" In the case, please include the following: 1. Attach the Initial Quick Test 2. Short video of the actual pressures via AC machine, showing the engine running, and hold a copy of the VIN/RO in view as well. 3. Picture of the forming gas check being performed with VIN/RO in view. 4. OBS recording of XENTRY AC actual values of compressor request to be on and current value. (s 5. Video recording of the leak being found via sniffer and location. Note - Please see the list of WIS documents for forming gas leak check, AC flushing and recharging of the system. The dryer must be replaced when there is a leak in the AC system.
- 11000542High-frequency interference noise may be heard from the speakers while driving. This complaint only occurs when "voice amplification" is active. Coupling noise of microphone signal in voice amplification. Intermediate remedy: The interference noise can be remedied by deactivating voice amplification: "Home" -> "Settings" -> "System" -> "Audio" and de-select "Voice amplification to rear" to switch off the function (see attachment). Note: To activate or deactivate the function, the ignition must be switched on, seat belts (at rear and front) must be fitted and the doors, windows and roof must be closed. Permanent solution: Perform software update of MBUX multimedia system (A26/17) to E419.5 (available from 06/19) or greater. Deactivate the voice amplification feature. Inform customer of function and effects of additional sounds caused by driving over bumps or uneven road surfaces.
Every Mercedes-Benz GLS 450 4MATIC model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.