2011 Mercedes-Benz ML550

Recalls

3 recalls name the 2011 Mercedes-Benz ML550. Newest first.

• Service brakes, hydraulic › Power assist › Vacuum

  Apr 26, 2024NHTSA 24V29800015,604 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML, GL, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.

  Risk and remedy

  Risk

  Reduced brake performance or brake failure can increase the risk of a crash.

  Remedy

  Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed on May 24, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MMUSA's number for this recall is 2024050001/2. This recall is an expansion of previous recall number 22V-315.

  Full recall details →

• Service brakes, hydraulic › Power assist › Vacuum

  May 9, 2022NHTSA 22V315000350,294 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML-Class, GL-Class, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.

  Risk and remedy

  Risk

  Reduced brake performance or brake failure can increase the risk of a crash.

  Remedy

  Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed June 30, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers for this recall are 2022050014, 2022050015 2022090006, & 2022090007.

  Full recall details →

• Air bags › Frontal › Driver side › Inflator module

  Feb 11, 2016NHTSA 16V081000711,159 vehicles

  Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350…

  Risk and remedy

  Risk

  In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

  Remedy

  MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.

  Full recall details →

Owner complaints

What owners report most

1. Exterior lighting3
2. Electrical system2
3. Air bags2
4. Wheels1
5. Service brakes1
6. Steering1
7. Visibility1

Latest complaints

• May 18, 2022NJ
  Service brakes

  The break line in the rear locate right above the gas tank is corroded by rust due to the clip is holding the break line allows the moisture to accumulate. The car will lose its break completely when this happens. There is no way for the car owner to inspect this problem until the car has no break power.

• Nov 15, 2017OK
  Air bags

  Takata recall...i have had a recall for a very long time on my air bags and have never been contacted by mercedes again after the initial recall. I am driving around with a potentially deadly device in my vehicle. I find this ridiculous especially since I am driving a mercedes which IS supposed to be one of the safest vehicles! Recall number 16v081. mfg recall number 2016020003

• Jan 14, 2017OK
  Air bags

  Takata recall. Have contacted dealership numerous times in the last year and half requesting when it would be fixed and are told it IS still pending. I would expect faster service on this potential danger with the defective driver side airbag.

• Dec 23, 2014TX50,000 mi
  Visibility › Sun/moon roof assembly
  Driving on a feeder road in light traffic at about 55 mph, we were startled by an enormous loud explosive sound on our sunroof of the ML 550, like a bomb sound. pulled over and slid the inside vented headliner/curtain back about 6 inches and saw a hole the size of two fists plus shattered glass.…

  Driving on a feeder road in light traffic at about 55 mph, we were startled by an enormous loud explosive sound on our sunroof of the ML 550, like a bomb sound. pulled over and slid the inside vented headliner/curtain back about 6 inches and saw a hole the size of two fists plus shattered glass. we recall that we weren't following behind any trucks. mercedes dealership estimated $2,777.00 to replace glass, drop headliner and remove broken glass shards/piece. mb did not offer any explanation as to defective sunroof glass. we owned numerous models of mercedes with sunroofs and never experienced such a frightening episode. *tr

• Sep 7, 2014CA2,047 mi
  Steering · Wheels
  The car would make loud noises even at a small speed, service mgr at smythe told me that mb had this defect and he stated he put loctite 648 per my notes o 8/24./2012 at 9N wheel bearing(s)! Mb should not have such a problem. My previous ML 500 also had a steering problem and mb never notified us…

  The car would make loud noises even at a small speed, service mgr at smythe told me that mb had this defect and he stated he put loctite 648 per my notes o 8/24./2012 at 9N wheel bearing(s)! Mb should not have such a problem. My previous ML 500 also had a steering problem and mb never notified us but fixed it after the warranty as they knew about it according to smythe svc mgr. I think mb must be proactive in rectifying such problems as we do not want them to cause problems after the warranty exp.! [xxx] information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6). *tr

• Aug 2, 2011CA8,000 mi
  Electrical system · Electrical system › Wiring · Exterior lighting › Back up lights · Exterior lighting › Brake lights · Exterior lighting › Tail lights
  Yesterday, I was driving our 2011 mercedes ml550 on a california highway, and suddenly lost my brake lights, turn signal lights and reverse lights, due to a rodent eating the wiring of the car. This IS the second time this year a rodent has eaten the wiring of this car. 4 months ago a rodent ate…

  Yesterday, I was driving our 2011 mercedes ml550 on a california highway, and suddenly lost my brake lights, turn signal lights and reverse lights, due to a rodent eating the wiring of the car. This IS the second time this year a rodent has eaten the wiring of this car. 4 months ago a rodent ate the main wiring loom and the repair cost $1000. We have owned 5 different mercedes benz models over the last 7 years. The wiring for each of these cars has been eaten by rodents more than once and caused us thousands of dollars worth of damage (obviously not covered under warranty). In most cases the cars were garaged. The cars were parked in various places around the country, including locations where no one else with other brand cars has had rodent damage. Every time we bring the cars in to be repaired the mercedes dealerships tells us "2 other people have brought their mercedes in today with rodent damage". I hear from one of the mb repairmen mercedes has chosen to use a material for the insulation of their wiring that IS attractive to rodents. Losing my lighting on a highway IS a safety issue for me. Being stuck responsible for paying for repairs that may be caused by a material choice mb has made seems unfair. *kb

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10248173Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) 2009-2012 GL-Class, ML-Class, R-Class, and S-Class (164/166, 251, 221 platforms) vehicles, the coding for the engine control unit does not correspond to the specifications as part of the BlueTEC update diesel field measure (aka Emission Modification). This could result in the VIN number not being read out from the vehicle. This could affect the vehicle smog check. MBUSA will conduct an Emission Service Campaign in which an authorized Mercedes-Benz dealer will update the SCN coding for the engine control unit on the affected vehicles.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10235996Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
• 10235978Recall Campaign announcement for Takata driver airbags.
• 10233794Why the warranty extension? On certain Model Year 2011-2016 CL/CLS/S/E/ML/SL/G/GL/GLE-Class vehicles with V8 engines, the exhaust valve assembly might not work properly and result in an engine misfire and potential illumination of the check engine Malfunction Indicator Lamp (MIL).
• 10205249No cooling output, fault code 9006 stored in air conditioning control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10205225Headlamps fogged.
• 10186145Creaking noise from fixed glass section of panoramic roof in area of rear passenger compartment grab handles
• 10186144Armrest In Center Console (Front) Only Opens On One Side Or Not At All - Model Series 167
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10167577Since 12/2012 (model 166) and since 06/2013 (model 242) the glass breakage loops are no longer in the side windows and rear window. Suitable interior protection ensures that the interior monitoring function continues to operate correctly.
• 10167572If it is necessary to replace an HV battery, the return will only be accepted with the filled-out ?Analysis Sheet for Transportability of High-Voltage Batteries Form? accompanied by: , the removed part, the quick test printout, the BMS control unit log printout, the repair documentation and with all required documentation listed in Section E of the Form.
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167561Xenon burner inoperative or flickers
• 10167488Engine rattling noise after engine start for several seconds
• 10167487Minor leaks at the oil duct of the left or right cylinder head of engines 157, 276 and 278. 1. Left cylinder head: Oil passage plug hole on left beside mechanical vacuum pump. 2. Right cylinder head: Oil passage plug hole below high-pressure pump housing.
• 10167040This Service Campaign has been initiated because Daimler AG (DAG), the manufacturer of Mercedes-Benz vehicles, has determined that the mbrace software does not correspond to current production configuration. An authorized Mercedes-Benz dealer will update the mbrace control module software at the next workshop visit.
• 10167007Engine diagnosis warning lamp active. Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.
• 10167006Engine diagnosis warning lamp active. Fault code 20BE1B and/or 20BD1B (The heating element of the AdBlue tank has a malfunction) is logged in the Blue-Tec control unit.
• 10167002Creaking noise when making vertical or longitudinal adjustment to electrical steering column
• 10166990Thumping noises from front axle when driving over bumps on road.
• 10166978Engine diagnosis warning lamp lights up - Fault code entry (FC) 14A600 or 14A700
• 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
• 10166975This Customer 1 Action has been initiated because certain mbrace subscribers were recently contacted by mbrace informing them that they need to have an i-button call performed to ensure their mbrace device has registered with the Verizon Telematics systems. If the i-button call failed or if the customer was unable to perform the i-button call, the mbrace agent instructed the customer to make an appointment with their dealer to have the issue corrected and/or i-button call performed. The vehicles impacted range from model year 2002 to 2014.
• 10166099Pneumatic comfort systems with insufficient performance, entirely inoperative or leaky.
• 10166088Noises from the mounting of the rear weight sensing system (WSS) sensors
• 10165850Side windows may make noises when closing and opening, or reverse direction when closing.

Every Mercedes-Benz ML550 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.